G2 Axle and Gear
Showing 529–576 of 1013 resultsSorted by popularity
-
Wheel Spacers and Adapters
G2 5x4.5 Inch Bolt Pattern with 1.25 Inch Offset Wheel Spacers (Black) – 93-65-125
Wheel Spacers and AdaptersG2 5x4.5 Inch Bolt Pattern with 1.25 Inch Offset Wheel Spacers (Black) – 93-65-125
- G2 Axle and Gear 93-65-125 wheel spacer for a 5 on 4.5 bolt pattern
- 1.25 inch thickness, aluminum with a black anodized finish
- Includes pre-installed wheel studs, lug nuts and thread locker compound
- Supplied in pairs
- Listed by G2 as universal fit; check hub pattern and clearance
SKU: G/293-65-125 -
-
-
Third Member Assemblies
G2 Toyota 8 Inch 5.29 High Pinion Third Member With Detroit Locker – 7-2043-529RL
Third Member AssembliesG2 Toyota 8 Inch 5.29 High Pinion Third Member With Detroit Locker – 7-2043-529RL
- G2 Toyota 8 inch high pinion third member, 5.29:1 gear ratio
- Detroit Locker differential listed
- High pinion layout aimed at ground clearance and driveshaft angles
- No Toyota years or models are listed
SKU: G/27-2043-529RL -
Third Member Assemblies
G2 Toyota 8 Inch Third Member 5.29 Ratio With Detroit Locker – 7-2043-529L
- G2 Toyota 8 inch third member, 5.29:1 gear ratio, part 7-2043-529L
- Heavy duty V6 third member case with standard pinion
- Auburn limited slip differential
- No Toyota model years are listed
SKU: G/27-2043-529L -
Dana 44 Axle Shafts
Dana 44 JK 35 Spline Rear Placer Gold Rear Chromoly Axle Shaft
- Rear axle shaft for Dana 44 JK, 35 splines, right or left side
- Forged 4340 chromoly steel, made in the USA
- Includes wheel studs and wheel bearings
- For use with 35 spline aftermarket lockers
- Fits 2007–2014 Jeep Wrangler JK models
SKU: G/2195-2052-35 -
Dana 44 Axle Shafts
G2 Placer Gold Series Dana 44 JK Rubicon Rear Axle Shaft (Passenger Side) – 195-2052-322
Dana 44 Axle ShaftsG2 Placer Gold Series Dana 44 JK Rubicon Rear Axle Shaft (Passenger Side) – 195-2052-322
- Rear passenger side axle shaft for Dana 44 JK Rubicon
- Forged 4340 chromoly steel, made in the USA
- Dual bolt pattern flange for 5 x 5 and 5 x 5.5
- For use with 32 spline aftermarket lockers
- Fits 2007–2014 Jeep Wrangler JK Rubicon
SKU: G/2195-2052-322 -
Dana 44 Axle Shafts
G2 Placer Gold Series Dana 44 JK Rubicon Rear Axle Shaft (Driver Side) – 195-2052-321
Dana 44 Axle ShaftsG2 Placer Gold Series Dana 44 JK Rubicon Rear Axle Shaft (Driver Side) – 195-2052-321
- Rear driver side axle shaft for Dana 44 JK Rubicon
- Forged 4340 chromoly steel, made in the USA
- Dual bolt pattern flange for 5 x 5 and 5 x 5.5
- For use with 32 spline aftermarket lockers
- Fits 2007–2014 Jeep Wrangler JK Rubicon
SKU: G/2195-2052-321 -
-
Ring and Pinions
G2 Dodge 10.5 Inch 14 Bolt 3.73 O.E.M. Ratio Ring and Pinion – 1-2097-373
- G2 Axle and Gear 3.73 O.E.M. series ring and pinion for the Chrysler 10.25 inch AAM rear axle, part 1-2097-373
- Rear axle location
- Universal fit listed by axle type
- Cooler and quieter running than aftermarket gears.
SKU: G/21-2097-373 -
Ring and Pinions
G2 GM 9.25 Inch IFS 3.73 O.E.M. Ratio Ring and Pinion – 1-2096-373
- G2 Axle and Gear 3.73 ratio O.E.M. series ring and pinion for the GM 9.25 inch IFS front axle, part 1-2096-373
- Front axle location
- Universal fit listed by axle type
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2096-373 -
Ring and Pinions
G2 GM 9.25 Inch IFS 3.42 O.E.M. Ratio Ring and Pinion – 1-2096-342
- G2 Axle and Gear 3.42 ratio O.E.M. series ring and pinion for the GM 9.25 inch IFS front axle, part 1-2096-342
- Front axle location
- Universal fit listed by axle type
- Quieter and cooler running than aftermarket gears.
SKU: G/21-2096-342 -
Ring and Pinions
G2 GM 8.25 Inch IFS 3.73 O.E.M. Ratio Ring and Pinion – 1-2095-373
- G2 Axle and Gear 3.73 ratio O.E.M. series ring and pinion for the GM 8.25 inch IFS front axle, part 1-2095-373
- Front axle location
- Universal fit listed by axle type
- Built to run cooler and quieter than aftermarket gears.
SKU: G/21-2095-373 -
Ring and Pinions
G2 GM 8.25 Inch IFS 3.42 O.E.M. Ratio Ring and Pinion – 1-2095-342
- G2 Axle and Gear 3.42 ratio O.E.M. series ring and pinion for the GM 8.25 inch IFS front axle, part 1-2095-342
- Front axle location
- Universal fit listed by axle type
- Cooler and quieter running than aftermarket gears.
SKU: G/21-2095-342 -
Ring and Pinions
G2 GM 7.25 Inch IFS 3.73 O.E.M. Ratio Ring and Pinion – 1-2094-373
- G2 Axle and Gear 3.73 ratio O.E.M. series ring and pinion for the GM 7.25 inch IFS front axle, part 1-2094-373
- Front axle location
- Universal fit listed by axle type
- Quieter and cooler running than aftermarket gears.
SKU: G/21-2094-373 -
Ring and Pinions
G2 GM 7.25 Inch IFS 3.42 O.E.M. Ratio Ring and Pinion – 1-2094-342
- G2 Axle and Gear 3.42 ratio O.E.M. series ring and pinion for the GM 7.25 inch IFS front axle, part 1-2094-342
- Front axle location
- Universal fit listed by axle type
- Cooler and quieter running than aftermarket gears.
SKU: G/21-2094-342 -
Ring and Pinions
G2 GM 7.25 Inch IFS 3.08 O.E.M. Ratio Ring and Pinion – 1-2094-308
- G2 Axle and Gear 3.08 ratio O.E.M. series ring and pinion for the GM 7.25 inch IFS front axle, part 1-2094-308
- Front axle location
- Universal fit listed by axle type
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2094-308 -
-
-
-
-
-
-
-
Ring and Pinions
Chrysler 9.25in. Front 3.73 O.E.M. Ratio Loaded Carrier
- G2 Axle and Gear 3.73 ratio O.E.M. loaded carrier for the Chrysler 9.25 inch front axle, part 1-2026-373L
- Front location.
- Universal fit listed by axle type, not by vehicle
- O.E.M. series, made under contract with original equipment manufacturers
SKU: G/21-2026-373L -
-
Ring and Pinions
G2 GM 11.5 Inch AAM 14 Bolt 4.11 O.E.M. Ratio Ring and Pinion – 1-2024-410
- G2 Axle and Gear 4.11 ratio O.E.M. series ring and pinion for the 11.5 inch AAM rear axle, part 1-2024-410
- Fits the Chrysler 11.5 inch housing.
- For use with all ratio carriers
- O.E.M. series, made under contract with original equipment manufacturers
SKU: G/21-2024-410 -
Ring and Pinions
G2 GM 8.5 Inch 10 Bolt 3.42 O.E.M. Ratio Ring and Pinion – 1-2021-342
- G2 Axle and Gear 3.42 ratio O.E.M. series ring and pinion for GM 10 bolt 8.5 inch and 8.6 inch axles, part 1-2021-342
- Front and rear locations listed
- O.E.M. series, made under contract with original equipment manufacturers
- Built to run cooler and quieter than aftermarket gears.
SKU: G/21-2021-342 -
Ring and Pinions
G2 GM 8.5 Inch 10 Bolt 3.08 O.E.M. Ratio Ring and Pinion – 1-2021-308
- G2 Axle and Gear 3.08 ratio O.E.M. series ring and pinion for GM 10 bolt 8.5 inch and 8.6 inch axles, part 1-2021-308
- Rear and front locations listed
- O.E.M. series, made under contract with original equipment manufacturers
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2021-308 -
Ring and Pinions
G2 GM 8 Inch IFS 4.10 O.E.M. Ratio Ring and Pinion – 1-2017-410
- G2 Axle and Gear 4.10 ratio O.E.M. series ring and pinion for the GM 10 bolt 8.0 inch IFS axle, part 1-2017-410
- Front and rear locations listed
- O.E.M. series, made under contract with original equipment manufacturers
- Designed to run cooler and quieter than aftermarket gears.
SKU: G/21-2017-410 -
Ring and Pinions
G2 GM 7.5 Inch 10 Bolt 3.73 O.E.M. Ratio Ring and Pinion – 1-2015-373
- G2 Axle and Gear 3.73 ratio O.E.M. series ring and pinion for the GM 10 bolt 7.5 inch rear axle, part 1-2015-373
- Rear axle location
- O.E.M. series, made under contract with original equipment manufacturers
- Designed to run cooler and quieter than aftermarket gears.
SKU: G/21-2015-373 -
Ring and Pinions
G2 GM 7.5 Inch 10 Bolt 3.42 O.E.M. Ratio Ring and Pinion – 1-2015-342
- G2 Axle and Gear 3.42 ratio O.E.M. series ring and pinion for the GM 10 bolt 7.5 inch rear axle, part 1-2015-342
- Rear axle location
- O.E.M. series, made under contract with original equipment manufacturers
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2015-342 -
Ring and Pinions
G2 Ford 8.8 Inch 3.08 O.E.M. Ratio Ring and Pinion – 1-2013-308
- G2 Axle and Gear 3.08 ratio O.E.M. series ring and pinion for the Ford 8.8 inch rear axle, part 1-2013-308
- Rear axle location
- O.E.M. series, made under contract with original equipment manufacturers
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2013-308 -
Ring and Pinions
G2 GM 9.5 Inch 14 Bolt 4.10 O.E.M. Ratio Ring and Pinion – 1-2010-410
- G2 Axle and Gear 4.10 ratio O.E.M. series ring and pinion for the GM 14 bolt 9.5 inch rear axle, part 1-2010-410
- Rear axle location
- O.E.M. series, made under contract with original equipment manufacturers
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2010-410 -
Ring and Pinions
G2 GM 9.5 Inch 14 Bolt 3.73 O.E.M. Ratio Ring and Pinion – 1-2010-373
- G2 Axle and Gear 3.73 ratio O.E.M. series ring and pinion for the GM 14 bolt 9.5 inch rear axle, part 1-2010-373
- Rear axle location
- O.E.M. series, made under contract with original equipment manufacturers
- Runs cooler and quieter than aftermarket gears.
SKU: G/21-2010-373 -
-































