Differential Crush Sleeves under Differential Parts covers the collapsible spacers and solid spacers that set pinion bearing preload during a gear setup. G2 Axle and Gear supplies crush sleeves for the Dana 30, GM 8.5 inch 10 bolt, Ford 7.5 and 9 inch and solid pinion spacers for Toyota 8 inch axles; Dana Spicer covers the Dana 35, Dana 50 and the JK rear Super 44; and Crown Automotive, Omix-ADA and Jeep supply factory sleeves for the Dana 30 KJ and Chrysler 9.25 inch. Match the axle below.
Differential Crush Sleeves
Showing 1–12 of 20 resultsSorted by popularity
-
Differential Crush Sleeves
Dana Spicer Dana 44 Crush Sleeve – 43916
- Dana Spicer crush sleeve for Dana 44 rear axles (part number D/S43916)
- Maintains proper pinion bearing preload
- Direct replacement for late model factory crush sleeves
- Aluminum sleeve for late model factory-style ring and pinions
SKU: D/S43916 -
Differential Crush Sleeves
Omix-ADA Dana 30/44 JK KJ Crush Sleeve – 16512.65
- Pinion bearing crush sleeve for Dana 30 JK and Dana 44 JK front axles
- Fits 2002-2012 Jeep Liberty KJ and 2015 Wrangler JK
- Also fits 2003-2006 Wrangler TJ Rubicon
- Omix-Ada part number 16512.65, UPC 804314134105
SKU: OAI16512.65 -
-
-
-
-
-
-
Dana 44 Miscellaneous Parts
Crown Automotive Dana 35 and Dana 44 Differential Crush Collar – 5183525AA
Dana 44 Miscellaneous PartsCrown Automotive Dana 35 and Dana 44 Differential Crush Collar – 5183525AA
- Differential crush collar for Dana 35 (186 mm) and Dana 44 (226 mm) rear axles.
- Fits 2007 to 2018 Jeep Wrangler JK and 2006 to 2008 Jeep Grand Cherokee WK, two- and four-door models.
- Sets pinion bearing preload when the pinion nut is tightened.
- Part number 5183525AA, UPC 849603001195.
SKU: CRO5183525AA -
-
What a crush sleeve does
The pinion gear in a differential rides on two tapered roller bearings that must be squeezed together to a precise preload, enough to remove play without overheating. A crush sleeve is a thin steel collar between the bearings that collapses a measured amount as the pinion nut is tightened; once it yields, the nut is turned until the pinion's rotating torque reaches the specification, usually a range of inch-pounds measured with a beam-type torque wrench. It is a one-time part. Any time the pinion nut is loosened, whether for a seal, a yoke or new gears, the sleeve has already collapsed and a new one is required. That is why these are consumables in every gear install.
Crush sleeve or solid spacer
- Crush sleeve: the factory method on the Dana 30, 35, 44 and 50, the Chrysler 9.25, the GM 8.5 inch 10 bolt and the Ford 7.5 and 9 inch. It is simple and forgiving on the first assembly, but it cannot be reused, and if the nut is over-tightened past the preload window there is no going back without a new sleeve.
- Solid spacer: a rigid spacer with a set of shims that replaces the crush sleeve. Preload is set by changing shim thickness, which takes more measuring but can be repeated and holds preload under hard use. The G2 solid pinion spacers for the Toyota 8 inch and 8 inch V6 axles are the kind used on rock crawlers and heavy trucks where big tires and shock loads can pound a crush sleeve into looseness.
For a daily-driven truck a crush sleeve is fine and is what the factory used. For a trail rig on 37s, or any axle you expect to open again, a solid spacer saves a sleeve each time and keeps preload consistent.
Matching the sleeve to the axle
Sleeves are specific to the axle housing and pinion, and sometimes to the generation. The listings here name the Dana 35 rear, the Dana 50 front, the JK rear Super 44, the Dana 30 KJ front on the Liberty, JK and Nitro, the Dana 30 TJ and reverse-rotation Dana 30, the Chrysler 9.25 rear on Dakota, Durango and Ram, the GM 8.5 inch, and the Ford 7.5 and 9 inch. The Dana 30 in a Liberty KJ is a different housing from the Dana 30 in a TJ, and their sleeves do not swap. Identify the axle from its tag, cover shape and the vehicle, and if a listing gives a height, like the 5/8 inch Super 44 sleeve, compare it with the old one before choosing.
Setting preload correctly
Install the pinion with new bearings and races, oil the bearings, and tighten the pinion nut in stages while checking rotating torque with the carrier out of the housing. The nut torque to collapse a sleeve is high, often several hundred foot-pounds, and the preload window afterward is narrow, so stop as soon as the pinion turns within specification. Too little preload lets the pinion walk and whine; too much cooks the bearings. Set pinion depth and backlash with the right shims, check the pattern with marking compound, and use a new pinion seal and nut. Gear setup is precision work with safety consequences; if you do not have a dial indicator, a case spreader where needed and the service manual specifications, have a differential shop do it. Confirm the part matches your exact axle and application before choosing.
Popular Differential Crush Sleeves brands
Differential Crush Sleeves FAQ
Can I reuse a crush sleeve if I only replaced the pinion seal?
No. Once the sleeve has collapsed it cannot provide preload again. Some mechanics mark the nut and reinstall it to the same position for a seal job, but that is a shortcut with risk. Fit a new sleeve or convert to a solid spacer whenever the pinion nut comes off.
What is the advantage of a solid pinion spacer?
Preload is set with shims and can be checked, adjusted and repeated. It holds up to shock loads from large tires and lockers better than a thin collapsed sleeve, and it saves buying a new sleeve each time the pinion comes out. It takes more measuring during setup.
How do I know what preload to set?
Use the specification in the factory service manual for your axle, given as rotating torque in inch-pounds for new bearings, measured with the carrier removed and a beam or dial type inch-pound torque wrench on the pinion nut. Used bearings have a lower specification. Values differ by axle, so look it up.
Are Dana 30 crush sleeves all the same?
No. The Dana 30 in a Liberty KJ, the Dana 30 in a TJ and the reverse-rotation Dana 30 use different pinion dimensions and sleeves, and the listings name them separately. Match the sleeve to the exact axle and vehicle, not just the Dana 30 name.










