Ford 9-inch vs Ford 8.8: how the two axles differ in gearing, pinion support and shaft retention, and why the 31-spline 8.8 is the…
Ring and pinion installation kits supply the bearings and hardware needed to set up a new ring and pinion gear set in a differential. This drivetrain branch lists master and minor kits for Dana 30, Dana 35, Dana 44, Dana 80, Ford 8.8 and 9 inch, GM 9.25 and Chrysler 8.25 axles. Brands include G2 Axle and Gear, Eaton and Rough Country. Compare kit contents on each product page, then compare the products below.
Ring and Pinion Installation Kits
Showing 1–12 of 216 resultsSorted by popularity
-
Ring and Pinion Installation Kits
Rough Country Dana 44 Rear Axle Master Install Kit – 54400031
- Master installation kit with bearings for a Dana 44 rear axle
- Written for the Dana 44 JK rear axle
- Part number 54400031
- Includes bearings, deluxe shim kit, pinion seal and sealing compounds
SKU: R/C54400031 -
Ring and Pinion Installation Kits
Rough Country Dana 30 Master Install Kit Jeep Wrangler JK – Front Axle – 53000011
Ring and Pinion Installation KitsRough Country Dana 30 Master Install Kit Jeep Wrangler JK – Front Axle – 53000011
- Master installation kit with bearings for a Dana 30 front axle
- Written for the Jeep Wrangler JK front axle
- Part number 53000011
- Includes carrier and pinion bearings, shims, seal and sealing compounds
SKU: R/C53000011 -
Ring and Pinion Installation Kits
G2 GM 9.25 Inch IFS Late Master Ring and Pinion Installation Kit – 35-2096A
Ring and Pinion Installation KitsG2 GM 9.25 Inch IFS Late Master Ring and Pinion Installation Kit – 35-2096A
- Master installation kit with bearings for a GM 9.25-inch independent front suspension axle
- Late-style 9.25-inch IFS kit
- Part number G/235-2096A
- Includes bearings, shims, pinion nut and seals
SKU: G/235-2096A -
Ring and Pinion Installation Kits
G2 Ford 9″ 2.96″ Bore With Daytona Pinion Master Ring and Pinion Installation Kit – 35-2011D
Ring and Pinion Installation KitsG2 Ford 9″ 2.96″ Bore With Daytona Pinion Master Ring and Pinion Installation Kit – 35-2011D
- Master installation kit with bearings for a Ford 9-inch axle with a Daytona pinion
- Written for the 2.96-inch bore housing
- Part number G/235-2011D
- Includes shims, pinion nut, crush sleeve and seals
SKU: G/235-2011D -
Ring and Pinion Installation Kits
G2 Ford 9″ 2.96″ Bore Master Ring and Pinion Installation Kit – 35-2011A
Ring and Pinion Installation KitsG2 Ford 9″ 2.96″ Bore Master Ring and Pinion Installation Kit – 35-2011A
- Master installation kit with bearings for a Ford 9-inch rear axle
- Written for the 2.96-inch bore housing
- Part number G/235-2011A
- Includes shims, pinion nut, crush sleeve and seals
SKU: G/235-2011A -
Ring and Pinion Installation Kits
G2 Ford 8.8″ 09 Up Late Master Ring and Pinion Installation Kit – 35-2013A
Ring and Pinion Installation KitsG2 Ford 8.8″ 09 Up Late Master Ring and Pinion Installation Kit – 35-2013A
- Master installation kit with bearings for a Ford 8.8-inch rear axle
- Written for the late-style 8.8-inch axle from 2009 onward
- Part number G/235-2013A
- Includes shims, pinion nut, crush sleeve and seals
SKU: G/235-2013A -
Ring and Pinion Installation Kits
G2 Dana 80 Ford Super Duty Master Ring and Pinion Installation Kit – 35-2080A
Ring and Pinion Installation KitsG2 Dana 80 Ford Super Duty Master Ring and Pinion Installation Kit – 35-2080A
- Master installation kit with bearings for a Dana 80 rear axle
- Written for Ford Super Duty applications
- Part number G/235-2080A
- Includes shim kit, pinion nut, crush sleeve and seals
SKU: G/235-2080A -
Ring and Pinion Installation Kits
G2 Dana 44 JK Rubicon With ARB Air Locker Master Ring and Pinion Installation Kit – 35-2051ARB
Ring and Pinion Installation KitsG2 Dana 44 JK Rubicon With ARB Air Locker Master Ring and Pinion Installation Kit – 35-2051ARB
- Based on the product title and description, fits the Dana 44 front axle of Jeep Wrangler JK models from 2007 to 2018
- Master installation kit with bearings for an ARB Air Locker equipped axle
- Part number G/235-2051ARB
- Includes shims, pinion nut, crush sleeve, seals and bearings
SKU: G/235-2051ARB -
-
Ring and Pinion Installation Kits
G2 Dana 30/44 JK 5.13 Ring and Pinion Minor Installation Kit – 4-JK-513M
Ring and Pinion Installation KitsG2 Dana 30/44 JK 5.13 Ring and Pinion Minor Installation Kit – 4-JK-513M
- Based on the product title and description, fits Jeep Wrangler JK models from 2007 to 2018
- 5.13 ratio, front and rear gear sets with minor installation kits for both axles
- Part number G/24-JK-513M
- Covers Dana 30 front and Dana 44 rear
SKU: G/24-JK-513M -
Ring and Pinion Installation Kits
G2 Dana 30 Master Ring and Pinion Install Kit with Eaton E-Locker – 35-2050L
Ring and Pinion Installation KitsG2 Dana 30 Master Ring and Pinion Install Kit with Eaton E-Locker – 35-2050L
- Master install kit for Dana 30 ring and pinion gears, part G/235-2050L
- Includes Timken bearings, ring gear bolts, shims and a pinion seal
- Eaton E-Locker offered with this kit
- No vehicle models are named; match the Dana 30 axle before choosing
SKU: G/235-2050L
What an install kit contains
When you regear an axle, the gears are only part of the job. The differential needs the right bearings, seals, shims and hardware to set the gear mesh correctly. An installation kit collects those parts so you can rebuild the differential with fresh wear items.
Master kit versus minor kit
- Master kit: includes a full set of bearings, races and seals, along with shims, crush sleeve or other hardware for the pinion and carrier. It is the thorough choice for a complete rebuild.
- Minor kit: includes the pinion bearings and hardware, but not the carrier bearings, and is used when the carrier bearings are in good condition and suitable for reuse.
Some kits also include a locker or limited-slip differential, or pair with an air locker. Read the listing to see what is included, and whether the kit is described for a front or rear axle.
Matching the kit to the axle
Axle models vary, and even within the same family there are version differences, such as spline counts, ring gear diameter, pinion style and carrier type. A Dana 30, 35, 44 or 80 each uses a different set of parts, and Ford 8.8, Ford 9 inch, GM 9.25 and Chrysler 8.25 axles are not interchangeable. Confirm the exact axle, the ratio of the gear set and whether the vehicle is a JK, WJ or another model. Check for features like IFS axles, which use different parts from solid axles.
Installation notes
Setting up gears requires measuring pinion depth, backlash and bearing preload with specialized tools, and a small error can cause noise, heat and early failure. Because of the tolerances involved, professional installation is strongly advised unless you have experience. Use the correct gear oil, follow the torque specifications for the ring gear bolts and carrier caps, and use a thread locker where specified. Check the contact pattern, and follow the manufacturer's break-in procedure after installation, including an early fluid change.
Fitment
Kits are made for specific axle models and model years. Confirm fitment for your exact year, make, model and axle, and check the manufacturer's specifications before choosing a part number.
Choosing a gear ratio and planning the build
A new gear set is usually chosen to restore performance after fitting larger tires, and the ratio should match the tire size, engine power and transmission. Numerically higher ratios, such as 4.88 or 5.13, improve acceleration and crawl control with big tires, but raise engine speed on the highway. Front and rear ratios must match on a four-wheel-drive vehicle, or the transfer case and axles can bind. Plan to regear both axles together, and decide whether to add a locker or limited-slip while the differential is open. Replace worn carrier parts and check the axle shafts, seals and housing for damage. After the job, a speedometer recalibration may be needed, and early fluid changes help remove break-in metal. Keep notes of the settings you measured for future service.
Common mistakes include reusing crush sleeves or old bearings, ignoring the manufacturer's pinion nut torque, mixing gear sets from different makers, and not verifying the carrier fits the new ratio. Gear sets are matched, so keep the ring and pinion together as supplied.
Related guides
- Is the Legendary Ford 9-Inch Overrated? Why Modern 4X4s Are Switching to the 8.8
Popular Ring and Pinion Installation Kits brands
- G2 Axle and Gear (197)
- Alloy USA (7)
- Eaton (5)
- Rough Country (2)
- Mountain Off Road Enterprises (2)
- Omix-Ada (1)
- Crown Automotive (1)
- Auburn Gear (1)
Ring and Pinion Installation Kits FAQ
What is the difference between master and minor install kits?
A master kit has a complete set of bearings and seals for both the pinion and the carrier. A minor kit covers only the pinion side and is used when carrier bearings can be reused. Check the contents list.
Can I install a ring and pinion myself?
It is possible, but it requires measuring pinion depth, backlash and preload with the right tools. Mistakes cause noise and damage, so many owners have a qualified shop do it. Follow the manufacturer's instructions.
How do I know which axle I have?
Check the axle tag, the cover shape and bolt count, the ring gear diameter, or the build sheet for your vehicle. Axle family and spline count matter, so identify yours carefully before choosing a kit.
Do I need new bearings with new gears?
It is common practice to install new bearings and seals with a new gear set, because used bearings may no longer match the wear pattern and can fail early. A kit is a convenient way to get these parts.



