Trail Gear
Showing 337–384 of 417 resultsSorted by popularity
-
Drive Shaft Spacer
Trail Gear Longfield Driveline Spacer – 301698-1-KIT
- Driveline spacer for a driveshaft that runs too short after a lift
- Trail Gear Longfield spacer in 1 inch and 1.5 inch sizes, with bolts
- Part number 301698-1-KIT, UPC 700006929991
- Universal fit; confirm year, model and trim
SKU: TGI301698-1-KIT -
Hydraulic Steering Mounting Bracket
Trail Gear Hydro Assist Brackets – 130054-1-KIT
- Trail Gear hydraulic steering ram mounting brackets, part 130054-1-KIT
- Brackets have a 5/8-inch bolt hole and are formed from 3/16-inch steel
- Designed for a 1.25-inch tie rod on a Toyota solid front axle
- Welding required for installation
SKU: TGI130054-1-KIT -
Steering Knuckle
Trail Gear Fully Loaded Six Shooter Knuckle Kit – 130052-1-KIT
- Two knuckles, two steering arms and shims for 1984–1995 Toyota 4Runner and 1979–1995 Toyota Pickup
- Two studs in each steering arm; thicker knuckle housing than stock
- High steer and cross over steering compatible
- Trail Gear part number 130052-1-KIT, UPC 70000621506
SKU: TGI130052-1-KIT -
-
-
-
-
D-Ring Shackle
Trail Gear Bolt-On D-Ring Mount – 303386-2-KIT
- Universal application bolt-on D-ring mount, part number 303386-2-KIT
- Mounting plate of 3/8” thick steel with a 1” thick D-ring mount section
- Designed for Trail Gear ¾” D-rings
- Includes ½” laser cut hardware
- Available in 3 x3 and 3 x3.5 mounting patterns
SKU: TGI303386-2-KIT -
-
-
-
-
-
Differential Drop Spacer Kit
Trail Gear Differential Drop Kit – 300814-1-KIT
- Trail Gear front differential drop kit, part number 300814-1-KIT
- Includes aluminum spacers, zinc-plated Grade 8 hardware and zinc-plated Class 8.8 bolts
- Direct Fit front application; confirm vehicle fit before ordering
SKU: TGI300814-1-KIT -
Drive Shaft Universal Joint
Trail Gear Creeper Toyota U Joint – 100065-1-KIT
- Trail Gear Creeper U-joint 100065-1-KIT, forged body
- Made for 1979-1995 4WD Toyota applications
- Tested to 4,700 ft-lbs of torque
- Includes four install clips and Zerk grease fitting
- Will not fit a CV head
SKU: TGI100065-1-KIT -
-
Rock Sliders and Guards
Trail Gear Rock Slider Mount Kit (Bare Steel) – 120007-1-KIT
- Six-leg rock slider mount kit with 3/16 in plate steel
- Plates weld to the frame; the rock slider welds to the plate
- Bare steel finish, welding required
- Confirm fit for your vehicle before ordering
SKU: TGI120007-1-KIT -
-
-
Steering Knuckles & Components
Trail Gear Magnum Knuckle Stud – 140171-1-KIT
- Trail Gear Magnum knuckle stud, part 140171-1-KIT, with an 8mm hex head
- Made from ARP 2000 material and hardened to 220,000 PSI
- Longer than stock to accommodate aftermarket steering arms
- Designed to be stronger than stock replacement Toyota knuckle studs
SKU: TGI140171-1-KIT -
-
-
-
Limiting Strap
Trail Gear 14 Inch Rock Assault Axle Limit Strap – 111277-KIT
- Trail Gear 14 in Rock Assault axle limit strap with 6-ply nylon webbing
- Part number 111277-KIT; 4130 Chromoly Steel buckles, zinc-plated
- Rated 9,000 lb test; minimal stretch to limit shock extension
- Universal fit, sold individually
SKU: TGI111277-KIT -
-
-
-
-
Spindle Seal
Trail Gear Trail Safe Toyots 8 Inch Knuckle Ball Wiper Seals – 140327-1-KIT
- Trail Gear Trail Safe Toyota 8 inch knuckle ball wiper seal kit, 140327-1-KIT
- Double-sided polyurethane seal keeps grease in and dirt out
- Includes 2 ball seal wipers, 2 rock rings, 16 ring bolts and 16 M6 lock washers
- Direct fit
SKU: TGI140327-1-KIT -
-
Spindle Nut And Washer Kit
Trail Gear Spindle Nut Kit – 140424-1-KIT
- Trail Gear spindle nut kit, part 140424-1-KIT
- Includes 2 nuts, a star washer and a flat index washer
- Covers one side of a front Toyota 8-inch axle
- No vehicle models or model years listed; confirm fit before ordering
SKU: TGI140424-1-KIT -
Weld In AN Threaded Bungs
Trail Gear Threaded Tube Adapter – 110074-1-KIT
- Weld-in threaded tube adapter (bung) with a 1.25 in. -12 right-hand thread
- Designed for Heim and Johnny Joints with a minimum tube ID of 1 inch
- Jam nut not included
- Universal fit, not tied to a specific vehicle
SKU: TGI110074-1-KIT -
-
-
-
Tubing Clamp
Trail Gear Tube Clamps – 180126-KIT
- Trail Gear O.D. tube clamp kit, code 180126-KIT, for 1.75 inch tubing.
- Two clamp halves with zinc plated screws; 1020 steel.
- Clamping force up to 8,600lbs, per Trail Gear.
- Attaches brackets to tubing without welding.
- No vehicles are named; confirm tube size before ordering.
SKU: TGI180126-KIT
