Dana Spicer
Showing 1–48 of 57 results
-
Replacement Axle Shafts
Dana Spicer Dana 50-Dana 60 Replacement Front Outer Axle Shaft – 2002692
- 99-04 Ford F-250/F-350
- Front axle
- Outer
- 30 spline
- 9.31 inches overall length
- Uses SPL55-3X and SPL55-4X
- Micro-alloy material improves strength of shaft
- Statistically controlled heat treatment ensures proper hardness
SKU: D/S2002692 -
Dana 44 Complete Assemblies
Dana Spicer Jeep JK Ultimate Dana 44 Front Axle Assembly 4.88 Ratio – 10010521
Dana 44 Complete AssembliesDana Spicer Jeep JK Ultimate Dana 44 Front Axle Assembly 4.88 Ratio – 10010521
- 2 and 4-door models
- 4.88 Genuine Spicer® Gears
- 5/16″ thick axle tubes for improved strength, rigidity and durability
- Redesigned and thicker brackets
- Spicer® chromoly axle shafts
- Spicer Life Series® (SPL®) 1350 u-joints with triple lip seals and full-circle clips
- Performance differential cover and Spicer® performance gasket
- Selectable electronic locking differential (harness sold separately, part number D/S10021771)
- Improved caster angle and pinion angle optimized for lifted Jeeps
- Increased gross axle weight rating
- Dana recommends using military tested and approved 75W-140 synthetic lube (not included)
SKU: D/S10010521 -
Dana 44 Drive Yokes and Flanges, Differential Pinion Shaft Nut
Dana Spicer Dana 30/44 Output Shaft Yoke Nut – 30185
Dana 44 Drive Yokes and Flanges, Differential Pinion Shaft NutDana Spicer Dana 30/44 Output Shaft Yoke Nut – 30185
- Fits 1987 to 2006 Wrangler, Rubicon and Unlimited with Dana 30
- Fits 1972 to 1975 and 1986 CJ with Dana 30 and Dana 44
- Fits 1987 to 2000 XJ Cherokee with Dana 30
- Fits 1986 to 1992 MJ Comanche with Dana 30
- Fits 1973 to 1991 SJ Full Size and J-series truck Dana 44
- Front
- Thread size .750-16
- Hex size 1.125
- Thickness 0.563
- For use with washer part D/S30186
SKU: D/S30185 -
Front Axle U-Joints
Dana Spicer Dana 60 Heavy Duty Axle U-Joint – SPL55-3X
- Dana 60
- Heavy Duty Forged Cross
- Perma-lube Improved Seals For Long Service Life
- O.E.M Replacement
- Inside Snap Ring
- Cup Size= 1.375in.
- Snap Ring To Snap Ring= 3.00in.
- This U-joint Replaces The Discontinued D/S5-806X
SKU: D/SSPL55-3X -
Driveshaft Flange Yoke
Dana Spicer 1310 Series Flange Yoke – 2-2-1379
- For Use With 1310 Series U-Joint
- Fits 1310 Series Flange Yokes
- Adapts Drive Shaft To Flat Flange Pinion Yokes
- 4.250in. Bolt Circle
- 2in. Female Pilot
- 19 deg Joint Angle
- 1.625in. Flange FaceTo Center Line
- 12MM bolts
- No Hardware Included
SKU: D/S2-2-1379