Select your vehicle

Axle Housing, under Performance Axle Components, covers the fabricated housings and housing parts for built axles: Trail Gear Rock Assault front housings with offset tubes and 3-link brackets for Toyota Pickup, 4Runner, Tacoma and Samurai, Trail Nine housings and bearing pockets, G2 CORE 44 Dana 44 housings for the Wrangler JK, Dynatrac ProRock 44 fronts for the TJ and XJ, Currie RockJock Dana 60 rear housings, and inspection hole and seal housing kits.Match the housing to your drivetrain and link setup, then compare the products below.

Showing 1–12 of 24 resultsSorted by popularity

When a stock housing is the weak link

A factory axle housing was designed for factory tires and factory power. Add 37 inch tires, a locker, low gears and a few years of hard landings, and the tubes bend, the center section cracks and the stock bracketry is in the wrong place for the suspension you now run. At that point a fabricated housing is the foundation of a durable axle: thicker DOM tubes, a stronger center section, forged inner knuckles and brackets set up for a link suspension. The parts here are housings and housing components only; gears, lockers, shafts, brakes and knuckles are chosen separately.

What is on offer

  • Toyota and Samurai housings from Trail Gear, for the 1979 to 1995 Pickup, 1984 to 1995 4Runner, 1995 to 2004 Tacoma and 1986 to 1995 Samurai. Built with 3 inch, 5/16 inch wall 1020 DOM tubes, forged 1035 steel knuckle balls, a 1/4 inch plate center section and offset tubes that add about 3/8 inch of ground clearance under the tubes. Options include right-hand drop, 3-link bracketry and a Toyota width housing offset for a Samurai transfer case.
  • Dana 44 housings for Jeeps: the G2 CORE 44 rear for the 2007 to 2016 JK with forged bearing caps, 3 inch by 5/16 inch tubes and 3/8 inch brackets, and the Dynatrac ProRock 44 front as a direct replacement for the TJ and XJ.
  • Dana 60 housings from Currie for the JK, with brackets welded in place for a bolt-in installation.
  • Trail Nine housings built around the Ford 9 inch center with 3 inch by 3/8 inch wall tubes, plus the matching seal housings and bearing pockets.
  • Housing parts: weld-on 4340 chromoly bearing pockets, a threaded inspection hole kit with an aluminum cap for checking gear pattern, and billet seal housing kits.

Specs that matter

Compare tube diameter and wall thickness first; 3 inch by 5/16 inch is a common strong combination for a trail rig, 3/8 inch wall for a one-ton build. Then width, measured wheel mounting surface to wheel mounting surface, which the Toyota housings list at 59 inches, and the position of the center section, since offset and right or left drop must match your transfer case output. Bracket placement for links, track bar and shocks should match your suspension or be left off for a custom setup. Finally, check the ring gear size the housing is built around and whether forged bearing caps or adjusters are included, as on the G2 CORE 44.

Building on a new housing

A bare housing goes to a competent axle shop or fabricator. Set-up includes checking the housing for straightness, installing the carrier and gears with correct pattern and backlash, pressing in the knuckle balls or inner Cs, welding any brackets that are not already attached, and verifying pinion angle in the vehicle. Weld-on bearing pockets and seal housings require the housing to be trued after welding. Bolt-in housings like the Currie JK Dana 60 and the Dynatrac ProRock 44 save that fabrication but still need gear set-up and brakes, and Dana 60 swaps change the bolt pattern to eight lug and require new wheels.

Legal and safety notes

Axles are steering and braking components. Have the finished axle inspected by someone qualified, torque everything to specification, and recheck after the first trips. Trail Gear notes a disc brake kit is required with its rear bearing pockets; plan the brake system alongside the housing rather than after it.

Popular Axle Housing brands

Axle Housing FAQ

Does a new axle housing include gears, lockers or shafts?

No. The housings here are the empty structure, sometimes with brackets, bearing caps or knuckle balls fitted. Ring and pinion, carrier or locker, axle shafts, brakes, knuckles and hubs are all chosen separately and installed by an axle shop during set-up.

What does offset tubes mean on a Trail Gear housing?

The axle tubes are positioned higher relative to the center section than stock, which raises the lowest point of the tubes and adds about 3/8 inch of ground clearance under them. The center section and differential still hang at their normal height.

Is a Dana 60 housing a bolt-in on a Wrangler JK?

Housings like the Currie RockJock Dana 60 III arrive with the JK brackets welded in place, so the housing bolts to the factory suspension mounts. You still need gears, shafts, brakes and eight lug wheels, since the Dana 60 bolt pattern differs from the stock five lug.

How thick should axle tubes be for a trail rig?

A 3 inch diameter tube with a 5/16 inch wall is a common strong choice for a trail rig on 35 to 40 inch tires, and 3/8 inch wall is used on one-ton and competition builds. Tube strength works together with a truss and good welds; thickness alone is not the whole story.