Differentials and carriers for 4×4 axles, including air-locking, selectable, and limited-slip designs. ARB Air Lockers, Eaton, Power Trax, and Auburn Gear supply units for Dana, GM, Chrysler, and Nissan axles, among others. Spline count, axle type, and ratio must all match. Use the product pages for these details, then compare the products below.
Differentials
Showing 1–12 of 40 resultsSorted by popularity
-
Differentials
Power Trax GM 8.5/8.6 Inch 30 Spline 2.73 Carrier and Up Grip LS Traction System – LS201030
DifferentialsPower Trax GM 8.5/8.6 Inch 30 Spline 2.73 Carrier and Up Grip LS Traction System – LS201030
- Fits GM 8.5-inch and 8.6-inch 10-bolt axles
- Limited-slip assembly with 30 axle splines
- Lists Silverado 1500, Sierra 1500, Tahoe, Suburban, Yukon and Escalade
- Carbon-fiber and steel friction plates
- Part number PTXLS201030
SKU: PTXLS201030 -
Differentials
Power Trax Ford 9 Inch 28 Or 31 Spline No Couplers Lock Right Locker – 1810-LR
- Automatic Lock Right locker that replaces the differential case
- Ford 9-inch rear axle, 28 or 31 spline axles
- Ring and pinion setup is not altered.
- Installs in the front, rear or both axles
- Part number PTX1810-LR
SKU: PTX1810-LR -
Differentials
Power Trax Ford 8.8 Inch 31 Spline Grip LS Traction System – LS108831
- Fits Ford F-150 (1983–2014), Explorer (1991–2010), Bronco (1983–1996) and Econoline vans
- Limited-slip assembly for the Ford 8.8-inch rear axle, 31 splines
- Carbon-fiber and steel friction plates in a fully machined case
- Comes fully assembled and can be rebuilt
- Part number PTXLS108831 with 10 ring gear bolts
SKU: PTXLS108831 -
Differentials
Power Trax Ford 8.8 Inch 31 Spline .875 Cross Pin Trac-Loc Case No-Slip – 9206883128
- Power Trax No-Slip Trac-Loc unit for a rear Ford 8.8-inch axle (part number 9206883128)
- Combines limited slip smoothness with locking traction
- Synchronized locking, no ratcheting sounds.
- Confirm the axle’s spline count before ordering.
SKU: PTX9206883128 -
Differentials
Power Trax Ford 8.8 Inch 28 Spline .750 Cross Pin Open Case No-Slip – 9206882807
- Power Trax No-Slip automatic locker for a Ford 8.8-inch axle with 28 splines (part number 9206882807)
- Synchronized locking with no ratcheting sounds.
- No ring and pinion setup required
- No special tools or oils needed
SKU: PTX9206882807 -
Differentials
Power Trax Dana 60 4.56 Carrier and Up 35 Spline Grip LOK Traction System – LK446035
- Power Trax Grip LOK traction system for a Dana 60 rear axle with 35 splines and 4.56 carrier and up (part number LK446035)
- Automatic mechanically actuated locking traction
- Fully machined case with 12 ring gear bolts
- Use 80W-90 GL-5 petroleum gear oil; no friction modifiers
SKU: PTXLK446035 -
Differentials
Power Trax Dana 35 27 Spline 3.54 Carrier and Up Grip PRO Traction System – GT443527
- Power Trax Grip PRO traction system for a Dana 35 rear axle with 27 splines and 3.54 carrier and up (part number GT443527)
- Progressive, throttle-controlled traction from 3×2 spiral gears
- Fully assembled; no friction plates or friction modifier
- Use 80W-90 GL-5 petroleum gear oil, not friction modifiers
SKU: PTXGT443527 -
-
Differentials
Ox Locker Dana 35 27 Spline 3.55 Up Air Selectable Locker – D35-355-27-AIR
- Air selectable locker for a Dana 35 rear axle with 27 splines and 3.55 and up gears (part number OXLD35-355-27-AIR)
- Open for street driving, full spool when engaged
- Forged cover with an integral air cylinder
- External air source required and not included
SKU: OXLD35-355-27-AIR -
Differentials
Ox Locker Dana 30 27 Spline 3.73 Up Air Selectable Locker – D30-373-27-AIR
- Air selectable locker for a Dana 30 axle with 27 splines and 3.73 and up gears (part number OXLD30-373-27-AIR)
- Open for street driving, full spool on demand
- Forged cover with an integral air cylinder
- Front or rear axle location listed; air source not included
SKU: OXLD30-373-27-AIR -
Differentials
Ox Locker Chrysler 8.25 Inch 27 Spline Air Selectable Locker – C825-273-27-AIR
- Air selectable locker for a Chrysler 8.25-inch rear axle with 27 splines (part number OXLC825-273-27-AIR)
- Open mode for street driving and full spool mode for maximum traction
- Forged cover with an integral air cylinder
- Requires an external air source, not included
SKU: OXLC825-273-27-AIR -
Differentials
Eaton Toyota 7.5″ IFS ELocker4 Locking Differential – 14220-1
- Electronic ELocker4 selectable locker for a Toyota 7.5-inch IFS front axle (part number 14220-1)
- Four pinion gear design for strength and capability
- Engages in 0.14 seconds
- Universal fit by axle type; no vehicle listed
SKU: EAT14220-1
Why upgrade a differential
An open differential sends power to the wheel with the least resistance, so a tire in the air or on loose ground can stop the vehicle while the other tire sits still. Locking and limited-slip differentials fix this. Off-roaders upgrade for better traction on climbs, in mud, and over ruts, while others replace a worn or damaged carrier after a rebuild.
Types of differentials
- Selectable lockers: locked by air, electric, or cable control only when you want it, then open for normal driving. ARB Air Lockers are an example of an air-operated type.
- Automatic lockers: engage on their own under power and release in turns, often with some noise or tire chirp.
- Limited-slip units: use clutches or gears to shift torque to the wheel with grip, giving a milder, always-on effect.
- Open carriers: a replacement for a damaged stock carrier or a base for a rebuild.
Fitment details
Differentials are very specific. Start with the axle model, such as a Dana 60, GM 14-bolt, Chrysler 8.25, or Nissan M226, and note whether it is front or rear. Then check the number of axle spline counts, which must match your axle shafts, and the ratio range the carrier covers. Many carriers are designed for a gear ratio range, such as 4.10 and numerically higher, so the ring gear and carrier break need to line up. For locking units that use air or electric actuation, confirm the housing style, since extra plumbing, wiring, and switches are part of the install.
Installation guidance
Installing a differential means setting up the ring and pinion, which includes adjusting backlash, pinion depth, and bearing preload. This demands special tools and experience, and a bad setup can destroy the gears quickly. Professional installation is strongly recommended unless you have done this work before. Replace worn bearings and seals at the same time, fill the axle with the fluid type the manufacturer calls for (some limited-slip designs need a friction modifier), and follow any break-in procedure.
Think about how a locker changes behavior. A locked axle can reduce steering and stress axle shafts, so drive carefully and disengage on pavement. Strong axle shafts are a good companion upgrade for any locker. Always confirm fitment for your exact year, make, model, and axle with the manufacturer's specifications.
Related parts and mistakes to avoid
A locker raises the load on the axle shafts, so many owners upgrade to stronger shafts and check the U-joints and the ring and pinion condition at the same time. Match the carrier to the housing's bearing size and the vehicle's gear ratio, and do not reuse worn carrier bearings. Be careful with air-operated units, since an air line leak or a poorly placed compressor can leave the locker unable to engage, and the lines need to be routed away from heat. Do not install a locker in a front axle without learning how it affects steering. Keep a record of the setup measurements for later service, and recheck the axle fluid level periodically.
Popular Differentials brands
- Eaton (11)
- ARB 4x4 Accessories (10)
- Power Trax (7)
- Dana Spicer (5)
- Auburn Gear (4)
- Ox Locker (3)
- Genuine Packages (1)
Differentials FAQ
What is the difference between a locker and a limited-slip?
A locker mechanically ties both wheels together for equal drive, either on demand or automatically. A limited-slip uses clutches or gears to bias torque to the wheel with grip. Lockers are more aggressive, while limited-slips are subtler.
How do I know my axle spline count?
The spline count is the number of splines on the axle shaft end. It is listed in axle specifications or can be counted when the shaft is removed. Many carriers are sold by spline count, so confirm before choosing.
Do I need to regear when installing a differential?
Not always, but the carrier must suit your ring gear and ratio, and installing a differential means resetting the gear pattern. Many owners replace gears and the carrier together to save labor.
Can I drive with a locker on the street?
Selectable lockers are driven open on the street, as designed. Automatic lockers can be noisy and affect handling in turns. Follow the maker's instructions and consider how the unit behaves on slippery pavement.










