Select your vehicle

G2 Dana 80 Ford Super Duty Master Ring and Pinion Installation Kit – 35-2080A

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Master installation kit with bearings for a Dana 80 rear axle
  • Written for Ford Super Duty applications
  • Part number G/235-2080A
  • Includes shim kit, pinion nut, crush sleeve and seals

Description

Overview

The G2 Axle and Gear Dana 80 master installation kit, part G/235-2080A, is made for the rear Dana 80 axle used in Ford Super Duty trucks.

The kit covers a full ring and pinion install on a Dana 80 rear, including the bearings and the shims that set gear depth. Use it with a matching G2 gear set.

Key features

  • Master kit with carrier and pinion bearings
  • Deluxe shim kit for setting pinion depth
  • Pinion seal, pinion nut and crush sleeve
  • Ring gear bolts, silicone sealer, Loctite and gear marking compound

Setting gear depth and preload

A master kit is only as good as the setup that follows. Pinion depth sets where the pinion sits relative to the ring gear, and carrier preload sets how the bearings sit under load. Both are set with shims and a crush sleeve, so the shim stack is measured and adjusted rather than installed once and forgotten.

Gear marking compound shows the contact pattern on the ring gear teeth. A pattern that is too high, too low or toward one edge means the depth or backlash needs adjusting before the axle carries load. Once the setup is right, finish the ring gear bolts and sealer as the job calls for.

  • Match the kit to the gear set before starting
  • Replace the crush sleeve rather than reusing it
  • Keep shims in order for reassembly

Specifications

Brand G2 Axle and Gear
Part number G/235-2080A
Axle location Rear
Axle type Dana 80
Kit type Master kit with bearings

Vehicle fitment

Make sure your truck’s year and axle match before buying.

Installation notes

Dana 80 pinion depth and carrier preload have to be set with the new gears in place. Use the included gear marking compound to check the contact pattern before the axle is loaded.

What’s included

Carrier bearings, pinion bearings, shim kit, pinion nut, crush sleeve, pinion seal, ring gear bolts, silicone sealer, Loctite and gear marking compound.

Not included: the Dana 80 ring and pinion gears, which the kit does not supply.

Questions & Answers

Will this Dana 80 master kit fit a Ford Super Duty?

The kit is made for the rear Dana 80 axle, and its name points to Ford Super Duty trucks. Confirm fit for your truck's year, model and axle before ordering.

Does the kit include the gears?

No. It is an install kit only, so a ring and pinion gear set for the Dana 80 must be bought separately and matched to the axle before the kit's shims and bearings are used.

Which items are in the kit?

It includes bearings, a shim kit, pinion nut, crush sleeve, pinion seal, ring gear bolts, silicone sealer, Loctite and gear marking compound for setting gear depth and checking the mesh.

What is this kit used for?

It is used to install a new ring and pinion in a Dana 80 rear axle. The shims and bearings in the kit are the parts that set gear depth and preload for the new gears.

Can the old pinion bearings be reused with new gears?

It is usually better to replace them. Pinion and carrier bearings are reset when new gears are fitted, and a worn bearing can change the preload that the new setup depends on. Inspect any reused bearing for roughness, play or discoloration first.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon