Select your vehicle
-13%

Rough Country Dana 30 Master Install Kit Jeep Wrangler JK – Front Axle – 53000011

Rough Country

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Master installation kit with bearings for a Dana 30 front axle
  • Written for the Jeep Wrangler JK front axle
  • Part number 53000011
  • Includes carrier and pinion bearings, shims, seal and sealing compounds

Description

Overview

The Rough Country Dana 30 master install kit, part 53000011, is an all-in-one set for installing a new ring and pinion in a Dana 30 front axle. Based on the product title and description, it is written for the Jeep Wrangler JK front axle, 2007–2018.

The kit collects the bearings, shims, seals and compounds that a gear swap needs, so the install does not depend on tracking each part down separately. The included shim kit makes it easier to set the correct shim amount for a clean gear mesh.

The kit is written for the front Dana 30 on JK models, so the bearings and seals are sized for that housing and the shim kit sets depth for the new gears. Check the 2007–2018 Jeep Wrangler JK fitment on your truck before ordering.

Key features

  • Carrier bearings and races, and pinion bearings and races
  • Deluxe shim kit for setting pinion depth
  • Pinion seal, ring gear bolts and pinion nut
  • Crush sleeve, oil baffle and slingers on select models
  • Thread locking compound, marking compound, brush and gasket sealing compound

Before you start

A gear swap in a Dana 30 front axle is a precise job. Pinion depth sets the mesh between the ring and pinion gears, and backlash sets the clearance between teeth. Both depend on shim choice and measurement, so take the time to measure before final assembly. Clean the housing thoroughly, since small metal chips in the bearing area can damage new bearings quickly.

Parts in a master kit are usually replaced as a group, so bearings, seals and sealing compound are installed with the gears rather than reused. Check the carrier and pinion bearings for fit, and confirm the front differential fluid level once the install is complete. A low-speed test drive afterward helps confirm the gears run quietly and the axle stays sealed.

  • Measure pinion depth before final assembly
  • Set backlash carefully before final assembly
  • Clean the housing and bearing bores fully
  • Replace seals along with the gears
  • Check fluid level after the first drive

Specifications

Brand Rough Country
Part number 53000011
Axle location Front
Axle type Dana 30
Kit type Master kit with bearings

Vehicle fitment

Based on the product title and description, this kit is for the front Dana 30 axle of 2007–2018 Jeep Wrangler JK models.

Wranglers from 2018 on, such as the JL, are not covered by these years. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Set the pinion depth with the deluxe shim kit, then use the marking compound to check the tooth contact before the front axle is put back into use.

What’s included

Carrier bearings and races, pinion bearings and races, pinion seal, ring gear bolts, deluxe shim kit, pinion nut, crush sleeve (select models), oil baffle and slingers (select models), thread locking compound, marking compound, brush and gasket sealing compound.

Not included: the ring and pinion gear set.

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2018All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will this Dana 30 master kit fit a 2007–2018 Jeep Wrangler JK?

Based on the product title and description, yes, for the front Dana 30 axle. Confirm your year, model and trim before ordering, since Wranglers from 2018 on are not covered by these years.

Does the kit include the gears?

No. It is an install kit, so a ring and pinion gear set for the front Dana 30 is needed separately, and the kit's shims are used to set pinion depth for those gears.

Are the crush sleeve and oil slingers always included?

Not always. The crush sleeve and oil baffle and slingers are included on select models only, so check the parts inside the box against your axle before starting the install.

What compounds come with the kit?

Thread locking compound, marking compound, brush and gasket sealing compound are included, so the install has the sealants and the contact-pattern marker needed for the front Dana 30.

Should the pinion seal and pinion nut be reused?

Replacing them is the usual approach, since a worn seal can leak and a reused nut may not hold torque as it did before. The kit includes both, so use the included parts during the gear swap.

What does a tooth contact check show?

The contact pattern shows where the gear teeth meet under load. A pattern that sits too high, too low or too close to one edge points to a shim or depth adjustment, so recheck before the axle is put into service.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon