Select your vehicle

Trail Gear Samurai Rock Assault Axle Housing Kit – 141038-3-KIT

Trail Gear

Shop Suzuki Samurai Axle Housing on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Toyota-width front axle housing offset for a Samurai transfer case
  • Press formed 1/4 in. plate steel center section with 3/4 in. of added clearance
  • Fits the 1986–1995 Suzuki Samurai in Base, JA, JL, JS, JX and JX SE trims
  • Includes the Differential Stud Eliminator Kit

Description

Overview

The Trail Gear Samurai Rock Assault Axle Housing Kit (part 141038-3-KIT) is a front axle housing for the 1986–1995 Suzuki Samurai, in Base, JA, JL, JS, JX and JX SE trims. It uses Toyota IFS width and is offset to line up with the Samurai transfer case, so the driveline stays in line.

The center section is press formed from 1/4 in. plate steel and shaped for at least 3/4 in. of added clearance under the differential. The axle tubes are 1/4 in. thick DOM steel with a 3 in. outer diameter, offset above the housing centerline, which adds 3/8 in. of ground clearance under the tubes.

Key features

  • Toyota-width housing offset to line up with the Samurai transfer case
  • Center section press formed from 1/4 in. plate steel
  • Differential mounting surface of 1/2 in. plate steel
  • Differential Stud Eliminator Kit included
  • Outer offset flanges of 4130 Chromoly
  • Offset 1/4 in. DOM axle tubes, 3 in. outer diameter
  • Custom length Chromoly axle shaft

Housing setup and clearance

A front axle housing sets the geometry for steering, braking and driveline angles, so the rest of the front end must be checked after it goes in. Measure the pinion angle, confirm the axle shafts reach the hubs without binding, and look at steering clearance at full lock. Offset housings can change how the driveline sits, so check U-joint angles once the vehicle is at ride height.

The differential cover area and axle tubes take the most stress off road, so welds and mounts are worth a look after the first trail trips. Use thread-locking compound where the hardware calls for it, and recheck bolts after a few runs. Paint or seal the bare steel once it is clean and dry to slow rust.

  • Check pinion angle after install
  • Confirm full steering lock clearance
  • Inspect welds and mounts after trail use

Specifications

Brand Trail Gear
Part number 141038-3-KIT
Front or rear Front
Housing type Toyota IFS width, offset for Samurai transfer case
Overall length 51 1/2 in. flange to flange
Axle tube 1/4 in. thick DOM steel, 3 in. outer diameter
Outer offset flanges 4130 Chromoly
Center section 1/4 in. press formed plate steel
Differential mounting surface 1/2 in. plate steel
Differential Toyota 8 in.
Ground clearance gain 3/8 in. under the axle tubing
Axle shaft Custom length Chromoly
Finish Arrives unpainted and lightly oiled

Vehicle fitment

It fits the 1986–1995 Suzuki Samurai in Base, JA, JL, JS, JX and JX SE trims.

The housing is built for the Suzuki Samurai. Although it uses Toyota-width dimensions and Toyota-style brake parts, Toyota Pickup, 4Runner and Wrangler models are not among the vehicles it is sold for.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The housing arrives unpainted and lightly oiled to prevent rust. Trail Gear recommends degreasing the housing inside and out before installation and painting it.

The housing uses a custom length Chromoly axle shaft that Trail Gear makes for it, and the brake backing plates and assemblies must be 1986–1995 Toyota Pickup or 4Runner type, stock or aftermarket.

An optional fill and inspection cap can be added to the housing.

What’s included

The housing with its Differential Stud Eliminator Kit.

Not included: The optional fill and inspection cap, and a steering ram mount, which the kit is listed without.

Fitment

VehicleYearsTrims
Suzuki Samurai1986–1995Base, JA, JL, JS, JX, JX SE

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the Trail Gear 141038-3-KIT fit a Suzuki Samurai?

Yes. It fits 1986–1995 Suzuki Samurai models in Base, JA, JL, JS, JX and JX SE trim. The housing is offset to line up with the Samurai transfer case.

Will this housing fit a Toyota 4Runner or Pickup?

It is made for the Samurai. The housing takes stock or aftermarket 1986–1995 Toyota Pickup or 4Runner brake backing plates and assemblies, so those brake parts are needed.

Does the housing come with a differential stud eliminator?

Yes. It comes with the Differential Stud Eliminator Kit, which keeps the differential from pulling out of the housing. The fill and inspection cap is an optional extra.

Does a housing swap require new brakes?

Brake parts often change with a housing swap. The brake backing plates and assemblies need to match the housing's hub and flange layout, so confirm them before final assembly. Check line length and routing once the axle is installed.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Suzuki Samurai Axle Housing on Amazon