Select your vehicle
-13%

JEEP JK FRONT CORE 44 METRIC HOUSING ADDED CASTER 4″-UP LIFT

G2 Axle and Gear

Shop Jeep Wrangler JK Axle Housing on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Front axle housing for 2007 and newer Jeep JK Wrangler, part 67-2051JKFL
  • Added caster for lifts of 4-inch and higher
  • High-pinion Dana 44 design with forged inner C-ends
  • Metric carrier bearings allow the factory air locker

Description

Overview

The G2 CORE 44 front axle housing, part number 67-2051JKFL, is a bolt-in front replacement for the Jeep JK Wrangler with added caster for lifts of 4 inches and higher. It is a high-pinion Dana 44 housing for 2007 and newer JK Wranglers, designed to handle loads that would normally bend a stock Dana 30 or a Rubicon Dana 44.

The housing accepts stock Dana 44 ring and pinion sets, axle shafts and aftermarket lockers. Its metric carrier bearings allow the factory air locker to be used, and the forged inner C-ends are part of the front bracketing.

Key features

  • Front bolt-in replacement housing
  • High-pinion Dana 44 gear design
  • Added caster for 4-inch and higher lift kits
  • Metric carrier bearings that allow use of the factory air locker
  • Massive forged inner C-ends and heavy-duty forged bearing caps
  • Three-inch tubing with a heavy-duty wall and CNC-formed brackets
  • Spanner nuts for backlash adjustment and an adjuster nut system for carrier pre-load

Caster and driveline angles

Caster and pinion angle are tied to lift height. Adding a lift changes the driveline angles, and a housing built for added caster sets the front axle to suit a raised front end. After installation, check alignment, the front driveshaft angles and the steering geometry, since these shift once the suspension is raised.

A bare housing is the start of a front axle build. Gears, shafts, lockers and brakes must be fitted before the housing is bolted in, and the correct carrier and bearings matter for long service life. Consider the steering components, including tie rod ends and ball joints, because a lift and added caster can load them sooner than stock.

  • Set driveline angles after the lift is installed
  • Inspect front U-joints for wear
  • Check steering components after the first off-road trip

Specifications

Brand G2 Axle and Gear
Part number 67-2051JKFL
UPC 631410119763
Position Front
Housing type CORE 44, high pinion, Dana 44
Caster Added caster for 4-inch and higher lift
Tube diameter 3 inches, heavy-duty DOM tubing
Installation Bolt-in

Vehicle fitment

It fits 2007 through 2018 Jeep JK Wranglers. Wrangler TJ, LJ and JL models are not covered by this front housing, and JK models with lifts under 4 inches should use the stock-caster version.

Wrangler TJ, LJ and JL models are not covered by this front housing, and a JK with lifts under 4 inches should use the stock-caster version. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The housing is a bolt-in front replacement, but it comes bare, so the ring and pinion, axle shafts and lockers are fitted before it goes on. Because the caster is set for a lift of 4 inches and higher, the alignment and driveline angles should be checked after installation.

What’s included

One bare front axle housing with the added-caster brackets, part 67-2051JKFL.

Not included: the ring and pinion gears, axle shafts, lockers and brakes, which are fitted separately.

SKU: G/267-2051JKFL Category:

Specification

Shipping weight 224.00 lbs
Package dimensions 77.30 × 23.50 × 20.30 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2018All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the G2 67-2051JKFL fit a 2012 Jeep Wrangler JK with a 4-inch lift?

Yes, for a 2007 and up JK Wrangler. The housing is built with added caster for lifts of 4 inches and higher, and the stated fit runs through 2018. Check your year, body style and lift height before ordering.

Is this the stock caster version?

No. The stock caster version is a separate G2 part for lifts up to 4 inches, while this housing has added caster for 4-inch and higher lifts.

Does this housing accept the factory air locker?

Yes. Its metric carrier bearings allow the factory air locker to be used, and the housing takes stock Dana 44 ring and pinion sets.

Do I need a new front driveshaft with this housing?

It depends on the lift and the driveline. A new housing changes the pinion angle, and a lift already moves it, so measure the angle once the housing is in. If the angle is off, a correction part or a new front driveshaft may be needed to keep the joints working smoothly.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler JK Axle Housing on Amazon