Drivetrain & Differential
Showing 49–60 of 1036 resultsSorted by popularity
-
Differential Guards
Rancho Rear Dana 44 Glide Plate – RS62117
- Rear Dana 44 glide plate for the Jeep Wrangler JL and related models (part number RS62117)
- Mounts to the rear axle casting, with no cutting or drilling
- 1/4 inch high-strength, low-alloy steel with red powder coat
- Works with OE and most aftermarket differential covers
SKU: RANRS62117 -
Differential Guards
Rancho Front Dana 44 Glide Plate – RS62116
- Front Dana 44 glide plate for the Jeep Wrangler JL (part number RS62116)
- Mounts to the front axle casting, with no cutting or drilling
- 1/4 inch high-strength, low-alloy steel with red powder coat
- Works with OE and most aftermarket differential covers
- Smoother glide over obstacles, forwards and backwards
SKU: RANRS62116 -
Differentials
Power Trax GM 8.5/8.6 Inch 30 Spline 2.73 Carrier and Up Grip LS Traction System – LS201030
DifferentialsPower Trax GM 8.5/8.6 Inch 30 Spline 2.73 Carrier and Up Grip LS Traction System – LS201030
- Fits GM 8.5-inch and 8.6-inch 10-bolt axles
- Limited-slip assembly with 30 axle splines
- Lists Silverado 1500, Sierra 1500, Tahoe, Suburban, Yukon and Escalade
- Carbon-fiber and steel friction plates
- Part number PTXLS201030
SKU: PTXLS201030 -
Differentials
Power Trax Ford 9 Inch 28 Or 31 Spline No Couplers Lock Right Locker – 1810-LR
- Automatic Lock Right locker that replaces the differential case
- Ford 9-inch rear axle, 28 or 31 spline axles
- Ring and pinion setup is not altered.
- Installs in the front, rear or both axles
- Part number PTX1810-LR
SKU: PTX1810-LR -
Differentials
Power Trax Ford 8.8 Inch 31 Spline Grip LS Traction System – LS108831
- Fits Ford F-150 (1983–2014), Explorer (1991–2010), Bronco (1983–1996) and Econoline vans
- Limited-slip assembly for the Ford 8.8-inch rear axle, 31 splines
- Carbon-fiber and steel friction plates in a fully machined case
- Comes fully assembled and can be rebuilt
- Part number PTXLS108831 with 10 ring gear bolts
SKU: PTXLS108831 -
Differentials
Power Trax Ford 8.8 Inch 31 Spline .875 Cross Pin Trac-Loc Case No-Slip – 9206883128
- Power Trax No-Slip Trac-Loc unit for a rear Ford 8.8-inch axle (part number 9206883128)
- Combines limited slip smoothness with locking traction
- Synchronized locking, no ratcheting sounds.
- Confirm the axle’s spline count before ordering.
SKU: PTX9206883128 -
Differentials
Power Trax Ford 8.8 Inch 28 Spline .750 Cross Pin Open Case No-Slip – 9206882807
- Power Trax No-Slip automatic locker for a Ford 8.8-inch axle with 28 splines (part number 9206882807)
- Synchronized locking with no ratcheting sounds.
- No ring and pinion setup required
- No special tools or oils needed
SKU: PTX9206882807 -
Differentials
Power Trax Dana 60 4.56 Carrier and Up 35 Spline Grip LOK Traction System – LK446035
- Power Trax Grip LOK traction system for a Dana 60 rear axle with 35 splines and 4.56 carrier and up (part number LK446035)
- Automatic mechanically actuated locking traction
- Fully machined case with 12 ring gear bolts
- Use 80W-90 GL-5 petroleum gear oil; no friction modifiers
SKU: PTXLK446035 -
Differentials
Power Trax Dana 35 27 Spline 3.54 Carrier and Up Grip PRO Traction System – GT443527
- Power Trax Grip PRO traction system for a Dana 35 rear axle with 27 splines and 3.54 carrier and up (part number GT443527)
- Progressive, throttle-controlled traction from 3×2 spiral gears
- Fully assembled; no friction plates or friction modifier
- Use 80W-90 GL-5 petroleum gear oil, not friction modifiers
SKU: PTXGT443527 -
-
Differential Covers
Poison Spyder Dana 44 Bombshell Differential Cover – 42-11-044-PC
- Dana 44 differential cover from Poison Spyder Customs (part number 42-11-044-PC)
- Cast nodular iron cover with recessed bolt pockets and a ramped profile
- Up to 1 inch thick around the bolt ring, 7/16 to 1/2 inch elsewhere, per the manufacturer
- Black powder coat
- Fits Dana 44 front and rear axles
SKU: PSC42-11-044-PC
What belongs in the drivetrain
The drivetrain moves power from the crankshaft to the ground. On a typical 4x4 that means the clutch or torque converter, the transmission, the transfer case, front and rear driveshafts, and the axle assemblies with their differentials, gears, bearings and seals. The subcategories here separate those systems so you can narrow down to complete axles and third members, performance axle components, OEM-style replacement axle parts, drive shafts, shifters or transfer case upgrades.
Identify the axle before you shop
Most axle parts are specific to the axle model, spline count and sometimes the production year. Product titles in this category refer to Dana 30, Dana 35, Dana 44, Dana 80 and AMC Model 20 housings, among others. Read the data tag on the differential housing or pull the cover and count ring gear bolts and measure the ring gear diameter. A part labeled for a Dana 44 front axle will not necessarily fit a Dana 44 rear axle, so note the axle location as well as the model.
Gear ratio and differential type
- Ring and pinion ratio: a numerically higher ratio such as 4.56 or 5.38 multiplies torque more and helps larger tires turn freely, at the cost of higher engine speed on the highway.
- Matched sets: ring and pinion gears are lapped and used as a pair, and front and rear ratios must match on a four-wheel-drive vehicle.
- Open, limited-slip and locking differentials: each handles traction differently, and clutch-type limited-slip units use clutch packs and friction additives that wear over time.
Installation and setup
Gear installation depends on correct pinion depth, backlash and bearing preload. These adjustments need dial indicators, marking compound and patience, and a mistake can destroy a new gear set within a few miles. Many owners hand this work to a driveline shop. Replace crush sleeves, seals and gaskets whenever the assembly is opened, and use the gear oil grade and capacity the axle manufacturer specifies. Torque fasteners to published values.
Confirming compatibility
Always confirm fitment for your exact year, make and model, and compare the part number against the manufacturer's specifications. Spline count, axle shaft diameter, bolt pattern and housing casting numbers all matter, and cross-referencing them avoids returning the wrong part after a weekend teardown.
Maintenance habits matter as much as the parts you choose. Check axle breather tubes so they are not clogged or collapsed, since a blocked breather builds pressure and pushes oil past the seals. Inspect universal joints and slip yokes for play, grease them if they have fittings, and look at the driveshaft angles after any lift or suspension change. Vibration at a particular speed often points to a driveshaft that is out of balance or running at too steep an angle. Gear oil that looks milky has taken on water, and metallic glitter on a magnetic drain plug is a sign that something inside deserves a closer look before it fails on the trail. Keep a record of the ratio, axle model and spline count for each axle so future orders are straightforward.
When budgeting a drivetrain project, remember the supporting parts. Bearings, seals, shims, carrier hardware and fluids are all needed alongside gears, and skipping them to save a little money tends to cost more later. If you are unsure which items belong together, a driveline specialist can review your list.
Popular Drivetrain & Differential brands
- G2 Axle and Gear (320)
- Dana Spicer (127)
- Crown Automotive (115)
- Omix-Ada (63)
- Moog (59)
- Centerforce (44)
- Trail Gear (39)
- ARB 4x4 Accessories (33)
- Alloy USA (26)
- Jeep (21)
- Eaton (16)
- TeraFlex (15)
Shop Drivetrain & Differential by type
- Performance Axle Components (669)
- Drive Shafts & Drive Shaft Components (78)
- OEM Replacement Axle Parts (93)
- Complete Axles & Third Members (32)
- Clutch & Bellhousing Components (98)
- Automatic Transmissions (26)
- Shifters & Shifter Components (13)
- Transfer Cases and Replacement Parts (12)
- Transfer Case Upgrades & Crawl Boxes (7)
- Manual Transmissions Parts (5)
- Transmission and Transfer Case Mounts (6)
Drivetrain & Differential FAQ
How do I know which Dana axle I have?
Check the axle tag or stamped casting numbers on the housing, count the differential cover bolts, and look at the cover shape. Measuring the ring gear diameter after removing the cover gives a definitive answer. Confirm against the manufacturer's specifications for your year and model.
Do I need to change both axle gear ratios at once?
On a part-time or full-time four-wheel-drive vehicle, yes. Front and rear ratios must match, because mismatched ratios make the axles fight each other and can damage the transfer case and gears. Regear both axles together with the same ratio.
Is a ring and pinion set something I can install at home?
It is possible, but setting pinion depth, backlash and bearing preload takes special tools and experience. Errors cause noise and rapid wear. Many owners use a driveline shop, especially for the first gear swap.
What fluids should I replace when I work on the drivetrain?
Replace gear oil in any axle you open, plus transmission and transfer case fluid if they are involved. Use the viscosity and friction modifier requirements specified for your axle, and replace seals and gaskets while the parts are apart.










