Drivetrain & Differential
Showing 37–48 of 1036 resultsSorted by popularity
-
-
Drive Shafts & Drive Shaft Components
Rough Country Rear CV Drive Shaft (4-6″ Lift) – 5074.1
- Rear double cardan CV driveshaft for 4 to 6 inch lifts
- Jeep Wrangler TJ with Dana 44 rear axle and manual transmission
- Slip yoke eliminator required
- Not for Rubicon or Unlimited models
- Part number R/C5074.1
SKU: R/C5074.1 -
Drive Shafts & Drive Shaft Components
Rough Country Rear CV Drive Shaft (4″ Lift) – 5087.1
- Rear CV driveshaft for 1994–1995 Jeep Wrangler YJ
- Double cardan style, recommended for 4-inch lifts
- Prevents driveline vibration and rear output shaft breakage
- Extended length, direct fit
- Slip yoke eliminator required
SKU: R/C5087.1 -
Drive Shafts & Drive Shaft Components
Rough Country Rear CV Drive Shaft – 5084.1
- Rear CV driveshaft for 1984–2001 Jeep Cherokee XJ
- Double cardan style, recommended for 4 to 6 inch lifts
- Prevents driveline vibration and rear output shaft breakage
- Automatic transmission models
- Slip yoke eliminator required
SKU: R/C5084.1 -
Differential Guards
Rough Country Front M186 Differential Skid Plate – 10623
- Front M186 differential skid plate for the Jeep Wrangler JL (part number 10623)
- 1/4 inch plate steel for underside protection
- Easy bolt-on installation with no cutting or drilling
- Allows access to the differential drain plug
SKU: R/C10623 -
-
Performance Axle Components
Rough Country Dana 44 Ring & Pinion Set 4.88 Ratio Jeep Wrangler JK Rear Axle – 54448822
Performance Axle ComponentsRough Country Dana 44 Ring & Pinion Set 4.88 Ratio Jeep Wrangler JK Rear Axle – 54448822
- Dana 44 rear ring and pinion set with a 4.88 ratio for Jeep Wrangler JK
- Part number 54448822
- Smooth-finished gears for the rear axle
- 10-year warranty against defects on the gear set
SKU: R/C54448822 -
Performance Axle Components
Rough Country Dana 44 Ring & Pinion Set 4.56 Ratio Jeep Wrangler JK Rear Axle – 54445622
Performance Axle ComponentsRough Country Dana 44 Ring & Pinion Set 4.56 Ratio Jeep Wrangler JK Rear Axle – 54445622
- Dana 44 rear ring and pinion set with a 4.56 ratio for Jeep Wrangler JK
- Part number 54445622
- Smooth-finished gears, 4.56 ratio, rear axle
- Comes with a 10-year warranty against manufacturing defects
SKU: R/C54445622 -
Ring and Pinion Installation Kits
Rough Country Dana 44 Rear Axle Master Install Kit – 54400031
- Master installation kit with bearings for a Dana 44 rear axle
- Written for the Dana 44 JK rear axle
- Part number 54400031
- Includes bearings, deluxe shim kit, pinion seal and sealing compounds
SKU: R/C54400031 -
Ring and Pinion Installation Kits
Rough Country Dana 30 Master Install Kit Jeep Wrangler JK – Front Axle – 53000011
Ring and Pinion Installation KitsRough Country Dana 30 Master Install Kit Jeep Wrangler JK – Front Axle – 53000011
- Master installation kit with bearings for a Dana 30 front axle
- Written for the Jeep Wrangler JK front axle
- Part number 53000011
- Includes carrier and pinion bearings, shims, seal and sealing compounds
SKU: R/C53000011 -
Axle Upgrade Kits
RCV Axles Ultimate Dana 44 35 Spline Front CV Axle Set for Rubicon – 35 Spline – CVJ44-JK-35
Axle Upgrade KitsRCV Axles Ultimate Dana 44 35 Spline Front CV Axle Set for Rubicon – 35 Spline – CVJ44-JK-35
- Dana 44 JK front constant velocity axle set with 35 splines
- CV design in place of U-joint shafts
- Built for a conventional locker in an aftermarket housing
- Limited lifetime warranty from RCV
SKU: RCVCVJ44-JK-35 -
Axle Shaft Tube Seal
RCV Axles Tube Seals for Wrangler JL Rubicon – JL-SK
- Tube seal kit for Dana 44 axle tubes on the Wrangler JL
- Two re-buildable tube seals, each with three outer O-rings and two inner washer seals
- Zerk fitting on the sides for greasing
- Fits 2018 Jeep Wrangler (JL) Rubicon, Sport, Sport S and Unlimited trims
SKU: RCVJL-SK
What belongs in the drivetrain
The drivetrain moves power from the crankshaft to the ground. On a typical 4x4 that means the clutch or torque converter, the transmission, the transfer case, front and rear driveshafts, and the axle assemblies with their differentials, gears, bearings and seals. The subcategories here separate those systems so you can narrow down to complete axles and third members, performance axle components, OEM-style replacement axle parts, drive shafts, shifters or transfer case upgrades.
Identify the axle before you shop
Most axle parts are specific to the axle model, spline count and sometimes the production year. Product titles in this category refer to Dana 30, Dana 35, Dana 44, Dana 80 and AMC Model 20 housings, among others. Read the data tag on the differential housing or pull the cover and count ring gear bolts and measure the ring gear diameter. A part labeled for a Dana 44 front axle will not necessarily fit a Dana 44 rear axle, so note the axle location as well as the model.
Gear ratio and differential type
- Ring and pinion ratio: a numerically higher ratio such as 4.56 or 5.38 multiplies torque more and helps larger tires turn freely, at the cost of higher engine speed on the highway.
- Matched sets: ring and pinion gears are lapped and used as a pair, and front and rear ratios must match on a four-wheel-drive vehicle.
- Open, limited-slip and locking differentials: each handles traction differently, and clutch-type limited-slip units use clutch packs and friction additives that wear over time.
Installation and setup
Gear installation depends on correct pinion depth, backlash and bearing preload. These adjustments need dial indicators, marking compound and patience, and a mistake can destroy a new gear set within a few miles. Many owners hand this work to a driveline shop. Replace crush sleeves, seals and gaskets whenever the assembly is opened, and use the gear oil grade and capacity the axle manufacturer specifies. Torque fasteners to published values.
Confirming compatibility
Always confirm fitment for your exact year, make and model, and compare the part number against the manufacturer's specifications. Spline count, axle shaft diameter, bolt pattern and housing casting numbers all matter, and cross-referencing them avoids returning the wrong part after a weekend teardown.
Maintenance habits matter as much as the parts you choose. Check axle breather tubes so they are not clogged or collapsed, since a blocked breather builds pressure and pushes oil past the seals. Inspect universal joints and slip yokes for play, grease them if they have fittings, and look at the driveshaft angles after any lift or suspension change. Vibration at a particular speed often points to a driveshaft that is out of balance or running at too steep an angle. Gear oil that looks milky has taken on water, and metallic glitter on a magnetic drain plug is a sign that something inside deserves a closer look before it fails on the trail. Keep a record of the ratio, axle model and spline count for each axle so future orders are straightforward.
When budgeting a drivetrain project, remember the supporting parts. Bearings, seals, shims, carrier hardware and fluids are all needed alongside gears, and skipping them to save a little money tends to cost more later. If you are unsure which items belong together, a driveline specialist can review your list.
Popular Drivetrain & Differential brands
- G2 Axle and Gear (320)
- Dana Spicer (127)
- Crown Automotive (115)
- Omix-Ada (63)
- Moog (59)
- Centerforce (44)
- Trail Gear (39)
- ARB 4x4 Accessories (33)
- Alloy USA (26)
- Jeep (21)
- Eaton (16)
- TeraFlex (15)
Shop Drivetrain & Differential by type
- Performance Axle Components (669)
- Drive Shafts & Drive Shaft Components (78)
- OEM Replacement Axle Parts (93)
- Complete Axles & Third Members (32)
- Clutch & Bellhousing Components (98)
- Automatic Transmissions (26)
- Shifters & Shifter Components (13)
- Transfer Cases and Replacement Parts (12)
- Transfer Case Upgrades & Crawl Boxes (7)
- Manual Transmissions Parts (5)
- Transmission and Transfer Case Mounts (6)
Drivetrain & Differential FAQ
How do I know which Dana axle I have?
Check the axle tag or stamped casting numbers on the housing, count the differential cover bolts, and look at the cover shape. Measuring the ring gear diameter after removing the cover gives a definitive answer. Confirm against the manufacturer's specifications for your year and model.
Do I need to change both axle gear ratios at once?
On a part-time or full-time four-wheel-drive vehicle, yes. Front and rear ratios must match, because mismatched ratios make the axles fight each other and can damage the transfer case and gears. Regear both axles together with the same ratio.
Is a ring and pinion set something I can install at home?
It is possible, but setting pinion depth, backlash and bearing preload takes special tools and experience. Errors cause noise and rapid wear. Many owners use a driveline shop, especially for the first gear swap.
What fluids should I replace when I work on the drivetrain?
Replace gear oil in any axle you open, plus transmission and transfer case fluid if they are involved. Use the viscosity and friction modifier requirements specified for your axle, and replace seals and gaskets while the parts are apart.






