Brackets, Gussets & Tabs
Showing 13–24 of 80 resultsSorted by popularity
-
Shock Mount Brackets
Blue Torch Fabworks Coil-Over Shock Mount for Inner C – BTF03082
- Coil-over shock mount for the inner C, cut from 1/4 in steel plate
- Curved lower contour matches the inner C
- Single piece; suits any tube diameter
- Part number BTF03082
- Check your vehicle’s year, model and trim before ordering the mount.
SKU: BTFBTF03082 -
Axle Truss
Artec Industries Rear Axle Swap Kit – TJ4418
- Rear Dana 44 axle swap kit with 1/4 inch thick truss and built-in link brackets
- Part number A/ITJ4418, fits 1997 to 2006 Jeep Wrangler TJ and 2004 to 2006 LJ
- Brackets for factory link, anti-sway bar and shock locations
- Steering ram mount not included
SKU: A/ITJ4418 -
-
Axle Bracket
Artec Industries Lower Link Axle Brackets – BR1010
- Artec Industries BR1010 lower link axle bracket, sold as a pair, part number A/IBR1010
- Universal fit control arm mount, not tied to a specific vehicle
- 2.625 mounting width with 9/16 bolt hole for common cartridge joints
- Made from 1/4 thick boxed steel plate
- Hole can be drilled out for 1.25 rod ends with spacers
SKU: A/IBR1010 -
Axle Ball Gussets
Artec Industries Leaf Spring Perch & Plates – BR1034
- Leaf spring perch and plates for spring over axle (SOA) swaps
- Sold as a pair, part number A/IBR1034
- Three leaf pin positions for one inch forward or back adjustment
- Includes truss end caps for Artec Modular Truss
- Hardware not included
SKU: A/IBR1034 -
Axle Truss
Artec Industries JK2TJ Front Axle Swap Kit with Truss – TJ3022
- Front swap kit for Dana 30 axles with 1/4 inch thick truss and built-in link brackets
- Part number A/ITJ3022; fits 1997 to 2006 Jeep Wrangler TJ and 2004 to 2006 Wrangler LJ Unlimited
- Brackets for factory link, anti-sway bar, tracbar and shock locations
- Steering ram mount not included
SKU: A/ITJ3022 -
Axle Truss
Artec Industries JK 1 Ton – Superduty (99-04) Front Dana 60 Swap Kit with Currie Johnny Joints – JK6042
Axle TrussArtec Industries JK 1 Ton – Superduty (99-04) Front Dana 60 Swap Kit with Currie Johnny Joints – JK6042
- Front Dana 60 axle swap kit with 1/4 inch truss and built-in link brackets, part number A/IJK6042
- Artec lists fitment for 2007 to 2018 Jeep Wrangler JK models
- Dana 60 axles need new wheels because the bolt pattern differs from factory JK 5 lug
- Brake and steering components are not included
- Check axle tube lengths of 3.0 inch and 24.5 inch before welding
SKU: A/IJK6042 -
Axle Truss
Artec Industries APEX Front Axel Truss – JL4501
- Fits JL Rubicon Dana 44 M210 front axles and all JT front axles
- APEX peaked top adds rigidity and removes long weld seams
- 1/8 inch mild steel, listed at 6 lbs
- Built for tires up to 40 inch on stock JL axles
- Minimum 1.5 inch lift recommended; welding required
SKU: A/IJL4501 -
Axle Truss
Artec Industries Adjustable Panhard Mount for D60 Truss – BR1026
- Artec Industries Panhard mount, part number A/IBR1026, for Dana 60 axles with Artec truss
- Three holes at 7, 8 and 9 inches from axle centerline
- Fits joints with a 1.75 inch mounting width
- Tube diameter 3 inches; sold as a single mount
- Welding required; the truss is not part of this item
SKU: A/IBR1026 -
Axle Truss
Artec Industries Adjustable Panhard Mount for D60 Truss – BR1025
- Artec Industries A/IBR1025 adjustable panhard mount for Dana 60 axles with Artec truss
- 3 inch tube diameter, single mount
- Holes at 7, 8 and 9 inches from axle centerline
- Designed for joints with a 1.75 inch mounting width
- Welding required for installation
SKU: A/IBR1025 -
-
Axle Bracket
Artec Industries 8.8 Swap Kit OEM LCA Brackets – TJ8805
- Artec Industries OEM lower control arm brackets, part number A/ITJ8805
- Driver and passenger side brackets only, not the full swap kit
- Directly replaces parts TR8801-N and TR8801-O
- Tied to the TJ 8.8 swap, 1997-2006 Jeep Wrangler TJ
SKU: A/ITJ8805
Parts for fabricators
These parts are building blocks for suspension and axle work. They are meant for welding or bolting into a project by people who understand the loads involved, such as when building a link suspension, swapping an axle or strengthening a weak point. Many are weld-on, so treat them as structural components.
What the subcategories cover
- Axle trusses: a steel brace that welds along the axle tube to resist bending, popular on Dana 30 and Dana 44 axles under larger tires.
- Axle brackets: link, track bar and Panhard mounts that weld to the axle housing.
- Ball gussets: reinforce the area around the steering knuckle ball joint.
- Shock and coilover mounts: locate shocks at the axle or frame.
- Spring perches and control arm mounts: hold leaf springs or arms in position.
- Tabs: laser-cut steel pieces for building custom mounts.
How to choose
First identify the axle or frame that the part must fit, such as Dana 30, Dana 44, Dana 60 or another axle, and whether it is a front or rear application. Tube diameter, bracket thickness and bolt hole size must match your project. Many mounts are listed as universal but still require careful measuring. Truss kits are often vehicle specific and may include axle swap hardware, so check what is included.
Look at the material and thickness, as thicker plate adds strength and weight. Check that the part is made from weldable steel and whether it arrives bare or coated. Coatings must be removed at weld areas.
Welding and installation
Axle and suspension welds carry safety-critical loads. Proper preparation, correct filler material, penetration and heat control matter, and a poor weld can fail without warning. If you do not have welding experience, hire a qualified fabricator. Measure geometry carefully, including pinion angle, link angles, track bar level and axle centering, before final welding. Avoid overheating axle tubes, since that can warp the housing.
Fitment and checks
After installation, inspect welds and bolts regularly, especially after hard trail use. Confirm fitment for your exact vehicle and axle, and follow the manufacturer's specifications and instructions. Alignment and driveline checks are recommended after changes.
Planning before you cut or weld
Good fabrication starts with measurement and a plan. Sketch the suspension geometry, including link lengths, angles and instant center, before locating any bracket. Use jack stands, a level surface and tools such as a straightedge, a tape measure and an angle finder to verify axle position. Tack weld parts first and recheck everything before final welds, because it is much easier to move a tack than a finished weld. Clean paint and coatings from the weld area, wear proper eye and respiratory protection, and keep a fire extinguisher nearby. Consider stress risers too: avoid abrupt ends on gussets, round the corners and keep welds away from high-flex areas. When the work is complete, inspect the welds, paint the bare metal to prevent rust and recheck bolts after the first trail run.
Common mistakes include welding without measuring first, using the wrong filler for the base steel, and trusting a bracket's appearance rather than its thickness. Check that the plate thickness suits the load, and avoid placing welds on the tension side of thin tubing without reinforcement.
Popular Brackets, Gussets & Tabs brands
- Artec Industries (33)
- Rubicon Express (15)
- G2 Axle and Gear (10)
- Trail Gear (6)
- TeraFlex (5)
- Blue Torch Fabworks (3)
- Rock Krawler (2)
- Low Range Offroad (1)
- Crown Automotive (1)
- Mountain Off Road Enterprises (1)
- Rugged Ridge (1)
- RT Off-Road (1)
Shop Brackets, Gussets & Tabs by type
- Axle Truss (43)
- Control Arm Mount (15)
- Axle Bracket (11)
- Axle Bracket Kits (5)
- Axle Ball Gussets (1)
- Shock Mount Brackets (1)
Brackets, Gussets & Tabs FAQ
What does an axle truss do?
A truss is a steel brace welded along the axle tube to resist bending and keep the housing straight. It is common on larger-tire builds. Fit depends on the axle model, so confirm the compatible axle on the product page.
Do I need to weld these brackets?
Many brackets and gussets are weld-on, while some mounts and kits bolt in. Check the product description. For safety-critical axle and suspension welds, use an experienced welder or professional fabricator.
What is a ball gusset?
A ball gusset is a reinforcing piece around the steering knuckle ball joint area on some axles. It helps strengthen the area, particularly with large tires or hard use. It must match your axle type.
What are laser-cut tabs used for?
Tabs are precision-cut steel pieces that fabricators use to make custom mounts, such as for links, shocks or brackets. Check the material thickness and the hole sizes and make sure they suit the load.










