Overview
The Artec Industries TR8802 is an 8.8 swap kit with truss for the rear axle of a 1993–1998 Jeep Grand Cherokee (ZJ). It uses a 1/4 inch thick mild steel truss top and brackets for the factory link, anti-sway bar, shock, track bar and coil spring locations, so a Ford 8.8 can replace the original axle.
The Ford Explorer 8.8 is the donor axle described. Artec compares it with the Dana 35: the 8.8 shares the same lug nut bolt pattern, has 3-1/4 inch tubes versus 2.625 inch, disc brakes on 1995 and newer units, 31 spline axle shafts, an 8.8 inch ring gear that Artec says is 120% stronger, and a trac-loc differential as stock. It is 20 pounds more than a Dana 35 and 1.25 inch narrower.
Key features
- 1/4 inch thick mild steel truss top reinforces the axle
- Brackets for upper and lower control arms, shock mounts, sway bar mounts, track bar mount and coil spring mounts
- Link mounts built into the truss for ease of installation
- Provides factory link, anti-sway bar and shock locations
- 8.8 inch diameter ring gear
- Disc brakes on 1995 and newer units
Before you buy a donor swap
A donor axle swap changes more than the axle itself. The new housing sets the wheel position, brake hardware, axle shaft length and driveline angle, so the whole setup should be planned together rather than one part at a time.
Plan for the driveshaft, the brake lines and the gear set before ordering. Measure the new ring and pinion against the existing transfer case output, and confirm the spring perches and shock mounts line up once the truss is in place. Plan on welding, grinding and fitting time, and budget for a shop with axle experience if the work is outside your skills.
- Confirm the gear ratio before you order the axle
- Plan a driveshaft check after the new axle is mounted
- Inspect the brake lines once the axle is in place
Specifications
| Brand | Artec Industries |
|---|---|
| Part number | TR8802 |
| UPC | 816791024763 |
| Axle type | Ford 8.8 |
| Axle location | Rear |
| Truss top thickness | 1/4 inch thick mild steel |
| Axle tube diameter | 3-1/4 inch (Dana 35: 2.625 inch) |
| Ring gear diameter | 8.8 inch |
| Axle shafts | 31 spline |
| Brakes | Disc (1995 and newer) |
| Differential | Trac-loc, as stock |
| Width compared with Dana 35 | 1.25 inch narrower |
| Weight compared with Dana 35 | 20 pounds more |
| Steering ram mount | Without steering ram mount |
| Fitment | Direct fit |
Vehicle fitment
The manufacturer fitment list covers the 1993–1998 Jeep Grand Cherokee (ZJ), including the 5.9 Limited, Base, Laredo, Limited, Orvis, SE and TSi trims.
It is built for the 1993–1998 Jeep Grand Cherokee (ZJ). Confirm fit for your vehicle’s year, model and trim before ordering, especially if you have a 1999–2004 Grand Cherokee (WJ) or another generation.
Installation notes
Installation requires welding and general fabrication. Some grinding and fitment may be needed, and brake line relocation is required. The 3.73 gear ratio may need to change to match Jeep gears, and wheel spacers may be needed to bring the width back to factory specs.
What’s included
The kit includes the truss and brackets for a complete axle swap: upper and lower control arm mounts, shock mounts, sway bar mounts, track bar mount and coil spring mounts.
Not included: the Ford 8.8 axle assembly, which is needed to complete the swap.














