Overview
The Power Trax Grip LS, part number PTXLS201030, is a limited-slip differential for GM 8.5- and 8.6-inch 10-bolt rear axles with 30 axle splines and a 1.31-inch axle shaft diameter. It is made for a 2.73 carrier and up. It fits a long run of Chevrolet, GMC, Cadillac, Buick, Hummer and Isuzu trucks and SUVs, most of them from the early 2000s.
The Grip LS uses carbon-fiber and steel friction plates inside a fully machined case, with S-spring preloading. It combines smooth limited-slip operation with the strength of a complete case, and it is designed to be streetable and consistent. The unit comes fully assembled and can be rebuilt because its friction plates sit on machined internal gears. It suits light trucks, sport utility vehicles and muscle cars, for daily commuting, recreation and work.
Key features
- Carbon-fiber and steel friction plate limited-slip design
- Fully machined, complete case with S-spring preload
- Comes fully assembled and is fully rebuildable
- 30 axle splines for GM 8.5- and 8.6-inch axles
- 10 ring gear bolts and 10 cover bolts
Setting up the carrier
Installing a complete differential assembly means the carrier must be set up with care. Ring and pinion contact, bearing preload and backlash all affect how smoothly the gears run and how long they last. Those settings should be checked with the right tools and measured against the housing before the truck returns to the road.
When the carrier is out, it is a good time to inspect the pinion bearings and seals, the axle bearings and the cover gasket. Replacing worn parts during the job saves having to open the axle again. Refill with the gear oil that the axle calls for, and check the level after the first short drive.
- Check ring and pinion contact before closing up
- Inspect pinion bearings and seals while open
- Refill with the correct gear oil
Specifications
| Brand | Power Trax |
|---|---|
| Part number | PTXLS201030 |
| Product line | Grip LS traction system |
| Differential type | Limited-slip assembly |
| Axle type | GM 10-bolt 8.5/8.6-inch |
| Axle location | Rear |
| Axle spline count | 30 splines |
| Axle shaft diameter | 1.31 inches |
| Ring gear bolts | 10 |
| Cover bolts | 10 |
| Carrier (per title) | 2.73 carrier and up |
| Fitment type | Direct fit |
Vehicle fitment
It fits the Chevrolet Silverado 1500 from 2001 to 2020, Silverado Classic (2007), Silverado 1500 HD (2001 to 2003 and 2005 to 2006), Tahoe and Suburban 1500 and 2500 from 2001 to 2013, Avalanche (2002 to 2013), Blazer (2001 to 2005), Colorado (2007 to 2012), S10 (2001 to 2004), Express 1500 (2001 to 2013), and Trailblazer (2002 to 2009). It fits the GMC Sierra 1500 from 2001 to 2020, Yukon from 2001 to 2013, Canyon from 2004 to 2012, Envoy from 2002 to 2009, and Sonoma from 2001 to 2004. Cadillac Escalade, Escalade ESV and Escalade EXT (2002 to 2013), Buick Rainier (2004 to 2007), Hummer H3 (2006 to 2010), Isuzu Ascender (2003 to 2008) and Saab 9-7x (2005 to 2009) are also covered. Check your year, model and trim before ordering.
Close vehicles that are not on the list include Silverado and Sierra models from 2021 on. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The Grip LS is a complete differential assembly for the carrier, so the ring and pinion setup and bearing preload must match the housing. Have a qualified axle shop install it and verify the setup before driving the truck.
What’s included
The unit comes fully assembled. Check the package contents for carrier bolts, bearings and other hardware before starting work.













