Select your vehicle

Bearings and install kits for the Dana 44 axle, including carrier bearings, axle shaft bearings, wheel bearings and retainer rings. They suit owners rebuilding a Dana 44 in a Jeep, truck or trail rig, or servicing a worn axle. Brands include G2 Axle and Gear, Crown Automotive, Dana Spicer and Omix-Ada. Open a product page for part numbers and kit contents, then compare the products below.

Showing 1–12 of 63 resultsSorted by popularity

Where bearings live in a Dana 44

A Dana 44 uses several different bearings, and it helps to know which one you are replacing. Pinion bearings support the pinion gear. Carrier bearings sit on each side of the differential carrier and let it rotate in the housing. In the rear, axle shaft bearings press into the tube ends and support the shafts, while front axles use wheel bearings and hubs at the knuckles. Install kits typically bundle bearings with races, seals or shims so that related parts are replaced together.

Signs of a worn bearing

  • A whine or hum that changes with road speed, not engine speed.
  • Growling or rumbling that gets louder in turns.
  • Play when you grab the wheel and rock it, or a wheel that runs hot after a drive.
  • Metal particles or a gritty look in the gear oil.

Do not ignore these symptoms. A failed bearing can damage the axle shaft, hub or differential, and a failed wheel bearing is a safety issue.

Choosing the correct kit

The Dana 44 was built in many variations, including front and rear versions, different spline counts and different vehicle applications. Listings often describe the axle by vehicle, year range, front or rear position and sometimes driver or passenger side. Match your kit to the axle as it exists on your vehicle today, since swaps and regears are common. Confirm fitment for your exact year, make and model, and verify the axle identification before ordering.

  • Carrier bearing kits generally include bearings and races for the differential.
  • Axle shaft bearings differ by axle type, such as semi-floating or full-floating rear axles.
  • Retainer rings and wheel bearings may be sold individually or as part of a kit.

Installation notes

Bearing work usually calls for a press, bearing separators, a seal driver and a torque wrench. Carrier bearings also require checking gear backlash and preload using shims, and a mistake there can wreck a ring and pinion set. If you do not have the tools or experience, a qualified differential shop is a sensible choice. Replace races as matched sets with their bearings, use the specified gear oil, and follow the factory service manual for torque and preload values.

Plan the job before you pull anything apart. Gather the seal kit, correct gear oil and any shims or crush sleeves your axle requires, and keep new bearings sealed in their packaging until installation so they stay clean. Mark the position of carrier caps and keep them paired with their original locations. Take photographs of each step, because reassembly is easier with a reference. Inspect related parts while the axle is open, including the axle shafts, spider gears, ring gear and housing surfaces. Wear on those parts often explains why the bearings failed. After a rebuild, follow the break-in procedure the gear maker recommends, which usually means gentle driving and an early oil change to remove fine metal from the new parts. If any step is unfamiliar, a shop with a press and setup gauges can save you from an expensive error.

Related guides

Popular Dana 44 Bearings and Install Kits brands

Dana 44 Bearings and Install Kits FAQ

How do I know which Dana 44 bearing I need?

Identify the axle first: front or rear, vehicle and year range, and spline count. Then match the bearing location, such as carrier, axle shaft or wheel. Compare part numbers and confirm fitment before ordering.

Should I replace bearings and races together?

Yes. Bearings and their races wear as a matched set, and installing a new bearing on a used race can cause early failure. Kits typically include both, and replacing seals at the same time is wise.

Do I need special tools to install carrier bearings?

Generally yes. A press, bearing puller or separator, and a torque wrench are common requirements, and setting backlash and preload takes dial indicators and shims. A differential shop can do this if you lack the tools.

What does a bad axle bearing sound like?

A steady hum or whine that changes with vehicle speed, or a growl in turns, often points to a bad wheel or axle bearing. Play or heat at the wheel confirms it. Have it inspected promptly.