Select your vehicle
-13%

G2 Dana 44 JK Rear Minor Ring and Pinion Installation Kit – 25-2052

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear minor ring and pinion installation kit for the Dana 44 JK
  • Includes shim kit, pinion nut, crush sleeve and pinion seal
  • Also has ring gear bolts, silicone sealer, Loctite and gear marking compound
  • G2 Axle and Gear part number 25-2052, UPC 631410095197

Description

Overview

The G2 Axle and Gear 25-2052 is a minor ring and pinion installation kit for the rear Dana 44 JK axle, which fits the 2007-2018 Jeep Wrangler JK. It is for a rear axle whose bearings do not need replacing, so the bearings stay in place.

The kit supplies a shim kit, a replacement pinion nut, a crush sleeve, a pinion seal, ring gear bolts, silicone sealer, Loctite and gear marking compound for setting up the rear ring and pinion.

Key features

  • Minor kit for the rear Dana 44 JK axle
  • Shim kit, pinion nut, crush sleeve and pinion seal
  • Ring gear bolts, silicone sealer, Loctite and gear marking compound
  • Rear axle location

On the trail

The rear axle carries the load of the whole drivetrain on rough ground, so a rear ring and pinion change should be done with trail use in mind. Gear teeth that were run hard or with worn bearings can chip, and a fresh setup helps the gears mesh smoothly under load. A careful break-in after the install is a good habit, especially on the first few trail runs.

Because the rear gears are set by shims and preload, small mistakes show up as noise or heat. After the first few runs, listen for whine, check the housing for warmth, and look for any oil seepage around the cover. Re-check the ring gear bolts after the first few trail runs, and inspect the rear axle seals when the gears are out.

  • Break in new gears gently on the first runs
  • Listen for changes in gear noise after the install
  • Re-check ring gear bolts after early trail use

Specifications

Brand G2 Axle and Gear
Part number 25-2052
UPC 631410095197
Kit type Minor kit, bearings not included
Axle type Dana 44 JK
Axle location Rear
Popular axle maker Dana

Vehicle fitment

The title and description name the rear Dana 44 JK axle, so this kit is for the 2007-2018 Jeep Wrangler (JK). The JK axle name is the basis for the model range; the kit is not a universal part.

It is not for the Wrangler (JL) or the Gladiator (JT). Confirm your vehicle’s year, model and trim before ordering.

Installation notes

A rear ring and pinion is set up by measurement. Use the gear marking compound to check the contact pattern, and choose shims by measurement rather than by guess.

What’s included

The kit includes the shim kit, pinion nut, crush sleeve, pinion seal, ring gear bolts, silicone sealer, Loctite and gear marking compound.

Not included: the ring and pinion gear set, which is a separate part.

Specification

Shipping weight 3.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2018All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Is the 25-2052 kit for the rear JK axle?

Yes. It is for the rear Dana 44 JK axle, and the axle location is rear. The front JK kit is a separate product.

Does the 25-2052 kit include a crush sleeve?

Yes. It includes a crush sleeve, a pinion nut, a pinion seal and a shim kit, along with the ring gear bolts and sealer.

Does the 25-2052 fit a 2010 Jeep Wrangler JK?

It is for the 2007-2018 Jeep Wrangler JK, which includes 2010 models. Confirm your vehicle's year, model and trim before ordering.

What signs show the rear pinion seal is leaking?

Gear oil on the inside of the wheel or on the brake parts, a low fluid level, or a dark film around the rear cover all point to a leaking seal. Replace the pinion seal during a ring and pinion job, then check the fluid level after the install.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon