Flex Joints, Rod Ends & Jam Nuts
Showing 25–36 of 116 resultsSorted by popularity
-
Rod Ends, Heim, Johnny & NG Joints
RockJock Johnny Joint Rod End – CE-9112P-12
- RockJock 4×4 Johnny Joint rod end, part number R/JCE-9112P-12
- 30 degrees of unrestricted movement in any direction
- Polyurethane bushing around a spherical ball, with zerk lubrication
- Zerk fitting for greasing, universal fit
SKU: R/JCE-9112P-12 -
Rod Ends, Heim, Johnny & NG Joints
RockJock Johnny Joint Rod End – CE-9110P-20
- Weld-on Johnny Joint rod end for fabricators and suspension builders
- 30 degrees of movement in any direction
- 2 1/2 inch outer diameter, 2.590 inch mounting width
- High-density urethane bushings and a zerk fitting
SKU: R/JCE-9110P-20 -
Rod Ends, Heim, Johnny & NG Joints
RockJock Johnny Joint Rod End – CE-9110CP
- RockJock 4×4 Johnny Joint rod end, part number R/JCE-9110CP
- Offers 30 degrees of unrestricted movement in any direction, versus 22 degrees on a common heim joint
- High density polyurethane bushing encases a spherical ball
- Zerk fitting for greasing; universal fit
SKU: R/JCE-9110CP -
-
-
-
-
-
-
What these parts do
Suspension links and steering linkages must pivot as the axle moves. Rubber bushings give that pivot with some flex, but a lot of articulation twists or binds them. Flex joints, rod ends and Heim joints are mechanical pivots built to allow wide, free movement, which is why they are common on rock crawlers, custom link suspensions and trail rigs with long-travel setups.
Joint types
- Flex joints (often called Johnny joints): A sealed housing with a ball and a polymer or bronze-style liner, allowing a wide angle of movement and usually accepting a grease fitting.
- Heim joints or rod ends: A spherical bearing inside a steel body with a threaded shank, widely used for adjustable links.
- Rebuild kits: Replacement liners, seals and hardware for restoring a worn joint.
- Jam nuts: Large locking nuts that secure a threaded joint so the link keeps its adjusted length.
What to compare
- Thread size and thread direction. Many rod ends come in right-hand and left-hand versions so that a link can be adjusted by turning the tube.
- Bore diameter and bolt size.
- Housing size and the arm or tube it must thread into or be welded to.
- Material and plating for corrosion resistance.
- Whether the joint is serviceable and greasable.
Noise, maintenance and wear
Joints can be louder and more prone to dirt contamination than rubber bushings, so keep boots and seals intact and grease fittings serviced on a regular schedule. Inspect joints after trail use for play, grit and torn seals. Many people replace liners as a routine maintenance item rather than waiting for failure.
Installation notes
Special tools are often required to press joints or liners in and out, which is why large joint tools appear alongside the joints themselves. Fabrication work, including welding threaded bungs, should only be done by someone with the skills to do it correctly, because a failed link or tie rod can cause a loss of vehicle control. Tighten jam nuts firmly against the joint, and verify that threads are engaged to at least the minimum depth the manufacturer recommends. Torque fasteners to specification, and have a suspension or steering rebuild checked by a professional.
Compatibility
Confirm thread size, direction and housing dimensions against your parts, and check the manufacturer's specifications. Joints are not interchangeable between every arm or link design.
Choosing the right size and grade
Thread size is expressed by diameter and pitch, such as a fine-thread or coarse-thread bolt, and mixing them damages threads. Also check the working angle of a joint: a rod end with a larger misalignment angle suits long links on a rig with a lot of articulation. For safety-critical links, favor forged and heat-treated parts from reputable makers over unmarked castings.
Mistakes to avoid
- Using a rod end in a way that puts it in bending rather than in line with the link.
- Leaving the shank threads only partly engaged.
- Over-greasing, which can push dirt past seals when done aggressively.
- Reusing worn liners or bolts that show galling.
Inspect the joints at regular intervals and replace anything that has play, since play grows quickly under load.
Popular Flex Joints, Rod Ends & Jam Nuts brands
- RockJock 4x4 (48)
- Artec Industries (16)
- Trail Gear (12)
- Rock Krawler (10)
- TeraFlex (8)
- Skyjacker (6)
- Rubicon Express (4)
- Mountain Off Road Enterprises (4)
- Daystar (3)
- Blue Torch Fabworks (3)
- Fabtech (2)
- Pro Comp Suspension (1)
Shop Flex Joints, Rod Ends & Jam Nuts by type
Flex Joints, Rod Ends & Jam Nuts FAQ
What is the difference between a Johnny joint and a Heim joint?
A Johnny joint is a sealed flex joint with a liner, often greasable, that suits control arms. A Heim joint is a spherical rod end, usually used on adjustable links and steering. Each has different angle and noise traits.
Why do some rod ends have left-hand threads?
A left-hand and right-hand pair lets you adjust link length by turning the center tube, without removing either end. This is common on adjustable control arms and track bars. Always match thread direction to the mating part.
What does a jam nut do?
A jam nut locks a threaded joint in place against the link or tube, so vibration does not change its adjusted length. It must be tightened firmly and the threads should be fully engaged.
Can I use rod ends for steering parts?
Only if the product is rated for steering use. Tie rod and drag link ends have specific load and angle needs, and a failure is dangerous. Use parts designed for the application and have the installation checked.











