Select your vehicle

Showing 25–36 of 118 resultsSorted by popularity

What belongs in this category

Trailer electrical covers everything between the tow vehicle and the trailer's lights and brakes. That includes brake controllers and their mounting brackets, vehicle-specific wiring harnesses, flat and round plug connectors, extension cables, T-connectors, circuit breakers, testers, dust covers and breakaway systems. A light trailer may need only a 4-way harness for tail, brake and turn lights, while a trailer with electric brakes needs a brake controller and a 7-way connection.

Connector types

  • 4-way flat: tail lights, brake lights and turn signals for light utility trailers.
  • 5-way flat: adds a fifth wire, often used for reverse lockout or auxiliary functions.
  • 6-way and 7-way: add circuits for electric brakes, a battery charge line and reverse lights. Round 7-way blades are common on heavier trailers.

Confirm the plug on your trailer and the socket on your vehicle before choosing adapters.

Brake controllers

A brake controller sends a regulated signal to a trailer's electric brakes when you press the pedal. Time-delayed controllers apply a preset output after a delay, while proportional controllers sense deceleration and scale braking to match. Plug-in or vehicle-specific harnesses can make installation cleaner than splicing, and mounting brackets keep the controller within easy reach of the driver. Always follow the manufacturer's setup procedure and test braking at low speed before towing a load.

Wiring harnesses and converters

  • Custom harnesses: plug into the vehicle's tail light circuit or an existing tow package connector with no cutting.
  • T-connectors: splice lighting circuits without cutting factory wires.
  • Converters: adapt a three-wire vehicle system to a separate trailer signal circuit.
  • Testers: a simple tester can confirm each circuit before a trip.

Safety and compatibility

Trailer brakes and lights are safety equipment, and laws on trailer brakes and breakaway systems vary by state and trailer weight. Check local regulations. A breakaway kit applies the trailer brakes if it separates from the tow vehicle, and its battery should be kept charged. Use wire and fuses rated for the load, secure connections against moisture, and keep plugs covered when not in use.

Harnesses are usually specific to model year and trim, so confirm fitment for your exact vehicle and the manufacturer's specifications. Then compare the products below.

Inspection routine before towing

Make a habit of checking the electrical connection every trip. Plug in the trailer, then have a helper confirm running lights, left and right turn signals and brake lights. Test the brake controller's manual lever to confirm the trailer brakes respond before you pull out. Look for frayed insulation, loose pins and corrosion in plug sockets, and apply a light coat of dielectric grease to the contacts.

Keep the connector off the ground when unhitched, and fit a dust cover so water and grit stay out. A small spare fuse kit and a tester are worth keeping in the glovebox.

Wire gauge matters as well. Brake circuits carry real current, so undersized wire can drop voltage and weaken braking. Follow the controller maker's gauge and fuse recommendations, keep wiring away from exhaust heat and moving parts, and use sealed or heat-shrink connections where moisture can reach them. Recheck connections periodically, since vibration loosens crimps over time.

Popular Brake Controllers & Electrical brands

Shop Brake Controllers & Electrical by type

Brake Controllers & Electrical FAQ

Do I need a brake controller for my trailer?

If the trailer has electric brakes, yes, because the tow vehicle has to send them a signal. Trailers with surge brakes or no brakes do not use one. Check your trailer's braking type and your local rules.

What is the difference between a 4-way and 7-way connector?

A 4-way flat plug carries tail, brake and turn signals. A 7-way adds circuits for electric brakes, a charge line, reverse lights and auxiliary power, which suits heavier trailers and campers.

What does a breakaway kit do?

If the trailer separates from the tow vehicle, the breakaway switch pulls a pin and sends battery power to the trailer's brakes. The kit includes a battery, which must be kept charged to work when needed.

Can I install a plug-in wiring harness myself?

Many custom harnesses are plug-and-play and need no splicing, so they are within reach of a careful DIYer. Confirm the connector match, follow the instructions, and test lights and brakes before towing. A shop can help with controller wiring.