Select your vehicle

Omix-ADA Front Wheel Bearing Seal – 16708.02

Omix-Ada

Shop Jeep CJ5 Spindle Seals on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits 1966 CJ3, 1966–1976 CJ5, 1966–1975 CJ6 and 1976 CJ7
  • Front wheel bearing seal for drum brakes
  • 2.125 inch spindle, Dana 30 Standard axle
  • Direct OE replacement; limited five year warranty

Description

Overview

The Omix-ADA 16708.02 is a front wheel bearing seal for drum brake Jeeps with a 2.125 inch spindle diameter and a Dana 30 Standard front axle, built as a direct OE replacement.

Omix-ADA builds its direct OE replacement Jeep parts to the original specifications and provides a limited five year warranty. This front wheel bearing seal is for drum brakes with a Dana 30 Standard axle and a 2.125 inch spindle. A wheel bearing seal keeps grease in the wheel bearing and dirt out, so it is a common item when bearings are serviced. Compare the spindle diameter and axle type with the front axle on your Jeep, and check the model years below, since the CJ7 is covered for 1976 only.

Key features

  • Front wheel bearing seal
  • For drum brakes
  • 2.125 inch spindle diameter
  • For a Dana 30 Standard front axle
  • Built to the original specifications by Omix-ADA as a direct OE replacement.
  • Limited five year warranty.

Seal care and bearing service

A front wheel bearing seal keeps grease inside the bearing and dirt and water out, which matters most on a drum brake Jeep that sees mud and river crossings. Once the seal lets grease escape or dirt enter, the bearing can run hot, collect grit and wear quickly. Checking the seal each time the hub is apart is a simple habit that prevents repeat jobs.

Clean the spindle before fitting the new seal and check that it sits square in the hub. Avoid driving the seal in unevenly, which can crack the lip or leave it short of its seat. Repack the bearing with fresh grease, and set the bearing preload to the procedure for your vehicle before the wheel goes back on.

  • Clean the spindle before fitting
  • Check the seal lip for nicks or cracks
  • Repack bearings with fresh grease

Specifications

Brand Omix-ADA
Part number 16708.02 (also shown as OAI16708.02)
Product type Front wheel bearing seal
Position Front
Axle location Front
Axle type Dana 30 Standard
Brakes Drum brakes
Spindle diameter 2.125 inch
Fitment type Direct fit
Warranty Limited five year warranty.

Vehicle fitment

The manufacturer fitment list for the Omix-ADA 16708.02 covers these vehicles: 1966 Jeep CJ3 (Base); 1966–1976 Jeep CJ5 (Base, Renegade); 1966–1975 Jeep CJ6 (Base); 1976 Jeep CJ7 (Base, Renegade).

It covers only the model years shown below. For example, the CJ7 is covered for 1976 only, and the CJ5 and CJ6 for the years shown. Later CJ7 years and other Jeep models fall outside that coverage. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Follow the vehicle service manual and tighten all fasteners to the specifications for your model.

  • Check the part against your vehicle before starting work.
  • Re-check fasteners after the first miles of driving, and again after hard off-road use.
  • Wheel bearing and brake work is safety-relevant; professional installation is recommended if you are not experienced.
  • Clean the spindle and check the bearing and brake components for wear while the hub is apart.

What’s included

One front wheel bearing seal.

Fitment

VehicleYearsTrims
Jeep CJ31966Base
Jeep CJ51966–1976Base, Renegade
Jeep CJ61966–1975Base
Jeep CJ71976Base, Renegade

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What vehicles does the Omix-ADA 16708.02 seal fit?

It is for the 1966 Jeep CJ3, 1966–1976 CJ5, 1966–1975 CJ6 and 1976 CJ7, in the trims covered. Confirm fit for your vehicle's year, model and trim before ordering.

What spindle size is the 16708.02 for?

It is sized for a 2.125 inch spindle diameter and drum brakes, on a front Dana 30 Standard axle. Measure your spindle and confirm the axle type before ordering.

Is the 16708.02 a front or rear seal?

It is a front wheel bearing seal. Both its position and axle location are front, with a Dana 30 Standard axle type. Confirm the axle on your Jeep before installing.

Is this an OE-style replacement?

Yes. It is built to the original specifications as a direct OE replacement and carries a limited five year warranty. Confirm fit for your vehicle before ordering.

How often should a front wheel bearing seal be replaced?

There is no fixed interval. Replace the seal when it leaks grease, shows cracks or hardening, or when the bearing is serviced. Inspect it each time the hub is apart, especially after water crossings.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep CJ5 Spindle Seals on Amazon