Dana 30 vs Dana 44 vs Dana 60: how to identify the axle under your Jeep or truck, what each one handles, and when…
Dana 44 Axle Parts, Axles, Gears, and Modifications
Showing 361–372 of 469 resultsSorted by popularity
-
Dana 44 Axle Shafts
G2 Dana 44 JK 30 Spline Rear Chromoly Axle Kit – 96-2052-1-30
- Rear axle kit for 2007–2014 Jeep Wrangler JK non-Rubicon
- 30 splines, dual drilled 5 x 5 and 5 x 5.5 bolt pattern
- Includes wheel bearings, seals and screw-in wheel studs
- Does not include a differential
- Forged chromoly shafts, heat treated
SKU: G/296-2052-1-30 -
-
Dana 44 Axle Shafts
G2 Dana 44 JK 35 Spline Placer Gold Rear Chromoly Axle Kit – 196-2052-002
- G2 Placer Gold Dana 44 JK rear chromoly axle kit, part 196-2052-002
- Made in the U.S.A. from forged 4340 chromoly
- 35 spline for use with aftermarket lockers
- Includes wheel studs and wheel bearings
SKU: G/2196-2052-002 -
Dana 44 Axle Shafts
G2 Dana 44 JK Rubicon 32 Spline Placer Gold Rear Chromoly Axle Kit – 196-2052-032
Dana 44 Axle ShaftsG2 Dana 44 JK Rubicon 32 Spline Placer Gold Rear Chromoly Axle Kit – 196-2052-032
- G2 Placer Gold rear chromoly axle kit, part number 196-2052-032
- Forged 4340 chromoly steel with 32 splines
- Dual bolt pattern flange, 5 x 5 and 5 x 5.5
- Includes wheel studs and wheel bearings
- Made in the U.S.A., for the Jeep JK Rubicon Dana 44 rear
SKU: G/2196-2052-032 -
Dana 44 Axle Shafts
G2 Dana 44 Chromalloy Inner Axle Shaft – 97-2045-001
- Driver side front inner shaft, 30 splines
- Overall length 16.62 inches, machined for full circle clips
- Accepts a 5-760 U-joint
- Built for 2003–2006 Jeep Dana 44 axles with the Rubicon option
- Forged alloy steel, heat treated
SKU: G/297-2045-001 -
Ring and Pinion Installation Kits
G2 Dana 44 Minor Ring and Pinion Installation Kit – 25-2033
- Minor ring and pinion installation kit for Dana 44 axles, part number 25-2033
- Includes pinion nut, pinion seal, crush sleeve, shims and ring gear bolts
- For use when the existing bearings stay in place
- Built for Dana 44 front and rear axles; check ring gear size before ordering
SKU: G/225-2033 -
Ring and Pinion Installation Kits
G2 Dana 44 JK 08 Up Rear Minor Ring and Pinion Installation Kit – 25-2053
Ring and Pinion Installation KitsG2 Dana 44 JK 08 Up Rear Minor Ring and Pinion Installation Kit – 25-2053
- Minor ring and pinion installation kit for a 2008-and-newer JK rear Dana 44, part number 25-2053
- Includes pinion nut, pinion seal, crush sleeve, shims and ring gear bolts
- Keeps the existing bearings: no bearing change needed
- Compound and sealer included: thread locking, gear marking and silicone
SKU: G/225-2053 -
Dana 44 Axle Shafts
G2 Dana 44 Chromalloy Inner Axle Shaft – 97-2033-006
- Passenger side front inner shaft, 30 splines
- Overall length 33.91 inches
- Fits 1978–1979 Ford Bronco, front axle, passenger side
- Accepts a 5-760X U-joint, machined for full circle clips
- Forged alloy steel, heat treated
SKU: G/297-2033-006 -
Dana 44 Axle Shafts
G2 Dana 44 Chromalloy Inner Axle Shaft – 97-2033-005
- Driver side front inner shaft, 30 splines
- Overall length 18.91 inches
- Fits 1978–1979 Ford Bronco in the front axle position, and 1968–1969 Ford F-150 trucks
- Accepts a 5-760X U-joint, machined for full circle clips
- Forged high-grade alloy steel, heat treated
SKU: G/297-2033-005 -
-
About the Dana 44
The Dana 44 is a popular medium-duty axle used in Jeeps, Ford trucks and Broncos, and other 4x4s, front or rear, and it is a common base for upgrades. Variants differ by spline count, housing, and mounting, so identify your axle carefully before ordering anything. The tag on the housing, the spline count, and the vehicle application are the starting points.
Parts here span routine maintenance items like seals and bearings through full gear and locker upgrades.
Gearing and differentials
Ring and pinion sets are chosen by ratio, such as 4.10, 4.56, or 5.13, usually to compensate for larger tires. Front and rear ratios must match, and sets should be installed with a master installation kit containing bearings, shims, and seals. Gear setup requires correct pinion depth and backlash measurements.
- Lockers and spools lock both wheels together for maximum traction.
- Limited slip units share torque between wheels while allowing some difference in speed.
- Open differential parts support rebuilds of the stock design.
Shafts, hubs, and wear parts
Axle shafts must match spline count and length, and some models need ABS tone rings or particular flange designs. Hubs, spindles, and ball joints wear with miles and trail use, and seals and bearings should be replaced together to protect the new components. U-joints and yokes need to match the shaft and driveline series.
Check the axle ratio, spline count, and brake configuration before purchasing any internal parts.
Installation guidance
Axle work is safety critical. Gear setup requires special tools and experience, and incorrect setup can cause noise and failure. Use jack stands, torque fasteners to specification, fill with the correct gear oil, and break in new gears gently. Professional installation is recommended for ring and pinion and locker work. Confirm fitment for your exact year, make, and model, and check the manufacturer's specifications.
Preparing for an axle project
Plan the project before tearing anything down. Identify the axle and its ratio, decide which parts to replace, and gather seals, bearings, gear oil, thread locker, and RTV or gaskets. Mark the driveshaft and carrier caps and keep parts organized.
Check axle housing straightness, tube condition, and mounting brackets. Many people upgrade axle shafts, lockers, and gears at the same time, because the housing is already open. Fill with the specified oil and drive gently for the first few hundred miles.
Spline count and axle shaft length are two of the first measurements to confirm. Dana 44 shafts come in different spline counts, and the inner and outer shafts on a front axle are different lengths on each side. Check the U-joint series, hub bolt pattern, and brake rotor mounting before choosing shafts.
Ring gear size, carrier break, and the pinion design also vary. Front and rear ring and pinion sets are not interchangeable, and a standard-rotation unit differs from a reverse-rotation unit found in some Jeep front axles. Carrier bearings and shims must be selected to suit the carrier you use.
Gear oil, additives, and limited slip friction modifiers all matter. Limited slip units often need a friction modifier, and lockers may need a particular type of oil. Check the oil level at each service, look for metal in the drain plug, and replace seals at the first sign of leaks to protect the brakes.
Related guides
- Dana 30 vs Dana 44 vs Dana 60: Which Axle Is Under Your Jeep or Truck, and When to Upgrade
- First SUV: The International Harvester Scout 80 Story
The first SUV wasn't a Jeep. See how the International Harvester Scout 80 came to be, how the Scout 800 and Scout II followed,…
- Is Your Dana 44 Vent Destroying Your Axle?
Learn how a Dana 44 axle vent works, which vent locations let water into the gear oil, and how to add a top-mounted breather…
Popular Dana 44 Axle Parts, Axles, Gears, and Modifications brands
- G2 Axle and Gear (178)
- Dana Spicer (93)
- Crown Automotive (58)
- Omix-Ada (35)
- Alloy USA (33)
- ARB 4x4 Accessories (13)
- TeraFlex (9)
- Auburn Gear (7)
- Detroit Locker (6)
- Rubicon Express (6)
- RCV Axles (4)
- Jeep (4)
Shop Dana 44 Axle Parts, Axles, Gears, and Modifications by type
- Dana 44 Axle Shafts (84)
- Dana 44 Ring and Pinion (68)
- Dana 44 Bearings and Install Kits (63)
- Dana 44 Oil Seals (56)
- Dana 44 Complete Assemblies (38)
- Dana 44 Differential Covers (31)
- Dana 44 Miscellaneous Parts (31)
- Dana 44 Hubs and Spindles (26)
- Dana 44 Lockers and Spools (26)
- Dana 44 Ball Joints (18)
- Dana 44 Drive Yokes and Flanges (13)
- Dana 44 U-Joints (9)
- Dana 44 Limited Slip Differentials and Parts (9)
- Dana 44 Open Differential Parts (7)
Dana 44 Axle Parts, Axles, Gears, and Modifications FAQ
How do I identify a Dana 44?
Look for a tag on the axle housing, a cover shape and bolt count, and the vehicle application. Spline count and ring gear diameter can be measured. Dana 44 variants differ, so verify before ordering parts.
What gear ratio should I choose?
Pick a ratio that restores performance with your tire size. Larger tires often call for numerically higher ratios, like 4.56 or 5.13, and front and rear ratios must match. Engine, transmission, and use all matter.
Do I need a master install kit?
It is strongly recommended with new gears. The kit includes bearings, seals, and shims needed to set pinion depth and backlash correctly. Reusing worn bearings can hurt gear life.
Can I install gears myself?
Only if you have the tools and experience. Setting pinion depth and backlash is precise work, and mistakes damage new gears. Many owners use a professional shop for ring and pinion installations.








