Fabrication & Tools
Showing 49–60 of 504 resultsSorted by popularity
-
-
-
-
-
Rod Ends, Heim, Johnny & NG Joints
RockJock 9/16 Inch Greasable Bolt with Hardware – CE-91107
- RockJock 4×4 9/16 inch greasable bolt with hardware, part number R/JCE-91107
- 9/16″ fine thread for 2 1/2″ Johnny Joints
- Zerk fitting installed in the bolt head
- Includes two flat washers and a crush nut
SKU: R/JCE-91107 -
Rod Ends, Heim, Johnny & NG Joints
RockJock 5/8″ Greasable Bolt with Hardware – CE-91108
- RockJock 4×4 greasable bolt with hardware, part number R/JCE-91108
- 5/8 inch fine thread, 4 inch long
- Grade 8 zerk fitted bolt with 2 flat washers and a stover nut
- Used to grease Johnny Joint rod ends, usable in other applications
SKU: R/JCE-91108 -
Rod Ends, Heim, Johnny & NG Joints
RockJock 2.5″ Narrow Forged Johnny Joint with 7/8″-14 RH Thread (2.625″ x .562″ Ball) – CE-9117N
Rod Ends, Heim, Johnny & NG JointsRockJock 2.5″ Narrow Forged Johnny Joint with 7/8″-14 RH Thread (2.625″ x .562″ Ball) – CE-9117N
- RockJock 4×4 narrow forged Johnny Joint rod end, part number R/JCE-9117N
- 7/8″-14 right hand threaded shank, fully assembled
- 2.625″ wide ball center with 9/16″ thru bolt hole
- Externally greasable through a zerk fitting
- Forged steel with gold zinc plating
SKU: R/JCE-9117N -
-
Rod Ends, Heim, Johnny & NG Joints
RockJock 2.5 Inch Johnny Joint – CE-9114L-14
- RockJock 4×4 R/JCE-9114L-14, forged male rod end Johnny Joint
- Universal fit; no specific vehicle is listed
- 7/16″ thru bolt hole, 2″ mounting width, greaseable and serviceable
- 3/4″-16 threads, 2 1/4″ long on the shank
- Gold zinc plated finish
SKU: R/JCE-9114L-14 -
Rod Ends, Heim, Johnny & NG Joints
RockJock 2.5 Inch Johnny Joint – CE-9110P-14
- RockJock 4×4 R/JCE-9110P-14, a 2.5-inch weld-on Johnny Joint kit
- 30 degrees of movement in any direction
- DOM tube outer shell with high-density urethane bushings
- 9/16-inch thru bolt hole and 2 5/8-inch mounting width
- No vehicle named; made for fabricated suspension builds
SKU: R/JCE-9110P-14 -
Rod Ends, Heim, Johnny & NG Joints
RockJock 2.5 Inch Forged Johnny Joint with 1-1/4 Inch RH Threaded Stud – CE-9114-14
Rod Ends, Heim, Johnny & NG JointsRockJock 2.5 Inch Forged Johnny Joint with 1-1/4 Inch RH Threaded Stud – CE-9114-14
- RockJock forged Johnny joint, 2.5 inch, 1-1/4 inch right-hand stud
- Greaseable through the outer shell, 7/16 inch thru bolt hole
- Accepts Johnny joint internals; fits RockJock adjustable upper arms
- Gold zinc plated, sold each
SKU: R/JCE-9114-14 -
Rod Ends, Heim, Johnny & NG Joints
RockJock 2.5 Inch Forged Johnny Joint with 1-1/4 Inch RH Threaded Stud – CE-9114
Rod Ends, Heim, Johnny & NG JointsRockJock 2.5 Inch Forged Johnny Joint with 1-1/4 Inch RH Threaded Stud – CE-9114
- RockJock 4×4 R/JCE-9114 forged Johnny Joint, fully assembled
- 2.5-inch joint with 1-1/4-inch-12 right hand threaded shank
- 9/16-inch thru bolt hole and 2.625-inch wide ball center
- Externally greasable through a zerk fitting
- Suited to RockJock adjustable lower control arms or universal arm builds
SKU: R/JCE-9114
What you will find here
Fabrication and tools covers the small parts that custom suspension and chassis work depends on. Rod ends and flex joints let links articulate, tube adapters join tubing to those joints, gussets and tabs reinforce brackets, and perches and shock mounts attach springs and shocks to axles and frames. Specialty tools such as joint presses, torsion key unloaders, spindle nut sockets and installation tools round out the category.
Rod ends and flex joints
Johnny Joint style flex joints use a bushing in a threaded housing, usually with urethane, and allow articulation while absorbing vibration. Heim joints, often called rod ends, use a spherical ball and are more rigid and precise, but they transmit more noise and need regular inspection. Left-hand and right-hand threaded ends, paired with jam nuts, let you adjust link length without removing the link. Misalignment spacers let a joint swing through its full range without binding.
Specs to match
- Thread size and direction: for example 3/4 inch versus 1-1/4 inch, left or right hand.
- Housing outside diameter and mounting width: this must match the tube or bracket.
- Bolt hole size: sets the bolt diameter through the joint.
- Weld-on or threaded: some adapters and joints must be welded.
- Serviceability: some joints grease through a fitting, and some can be rebuilt.
Safety and workmanship
Suspension links, cage components and steering parts are safety-critical. Welding should be done by someone qualified, using correct tube wall thickness, proper penetration and heat control. Use proper-grade hardware, tighten to specification, and fit jam nuts correctly with full thread engagement. Inspect joints regularly for play and cracks. For steering and suspension work you are unsure about, have a professional fabricator build and inspect it.
Think about the complete link before buying individual parts. A control arm or link is built from two ends, a tube and the hardware, and every piece must match: the thread of the ends has to match the tube adapter, and the bolt diameter must match the mounts on the axle and frame. Measure the center-to-center length you need with the suspension at ride height and again at full droop and full compression, so the ends never bind or run out of thread engagement.
The tools in this category make jobs safer and tidier. Joint presses and installation tools prevent damaged bushings, and a spindle nut socket or torsion key tool does a job that is awkward and risky with improvised tools. Brackets, gussets and tabs should be welded with clean, fully fused beads and placed to spread loads into the surrounding structure rather than concentrating stress on a single spot. Never grind or drill structural components without understanding how that changes their strength. Keep a record of the torque used on every fastener and recheck after the first trail outing.
Keep spare hardware on hand for trail repairs, including a few jam nuts, grade-rated bolts, nylon-insert locknuts and extra misalignment spacers, since these small parts are easy to lose and hard to improvise. Mark the final position of each adjustable end with paint so you can see at a glance if anything has turned. Store rod ends clean and lightly oiled, because rust inside a spherical bearing causes binding and premature wear.
Compatibility
Many items here are universal, so fitment depends on your design. Confirm dimensions and thread specifications from the manufacturer before choosing a product below.
Popular Fabrication & Tools brands
- Artec Industries (94)
- Rubicon Express (72)
- RockJock 4x4 (56)
- Currie (52)
- Trail Gear (44)
- TeraFlex (31)
- Fabtech (26)
- Blue Torch Fabworks (23)
- Rock Krawler (18)
- Mountain Off Road Enterprises (15)
- Poison Spyder Customs (13)
- Pro Comp Suspension (13)
Shop Fabrication & Tools by type
- Shock Mounts (72)
- Gussets & Tabs (59)
- Flex Joints, Rod Ends & Jam Nuts (116)
- Flex Joints (62)
- Tube Adapters (26)
- Brackets, Gussets & Tabs (80)
- Jam Nuts (17)
- Leaf Spring Perch (17)
- Tubing & Tube Adapters (12)
- Misalignment Spacers & Washers (9)
- Shock Absorber Wrench (8)
- Joint Tools (6)
- Roll Cage Gusset (7)
- Leaf Spring Accessories (3)
- Link Arm End (6)
- Nut-Sert Installation Tool (1)
- Sockets (3)
- Tool Bits (2)
- Specialty Tools (4)
- Drill Bits (0)
- Siphons (2)
- Hand Tools (2)
- Torsion Key Unloading Tool (2)
- Spindle Nut Socket (2)
- Oil Screen Installation Tool (0)
- Hose Cutter (1)
- Roll Cage Accessories (1)
- Knuckle Pull Scale (1)
- Garage Tools (1)
Fabrication & Tools FAQ
What is a Johnny Joint?
A Johnny Joint is a trademarked style of flex joint that places a bushing inside a threaded housing so a link or arm can pivot and twist. It is quieter than a heim joint and widely used in control arms and track bars.
What is the difference between a heim joint and a flex joint?
A heim joint uses a metal spherical bearing for precise, rigid movement, but it can be noisy and needs inspection. A flex joint uses a bushing, often urethane, which dampens noise and vibration while still letting the link articulate.
Why do rod ends come in left-hand and right-hand threads?
Pairing one left-hand and one right-hand end lets you turn a single link tube to lengthen or shorten it without removing either end. Jam nuts then lock the adjustment so the threads cannot back out.
Do I need to weld tube adapters?
Many tube adapters and weld-in joints must be welded to the tubing, while others thread in. Check the product description. Welding structural suspension parts should be done by a qualified fabricator using suitable tube material and technique.








