Performance Axle Components
Showing 625–636 of 669 resultsSorted by popularity
-
Differential Covers
G2 Ford 8.8 Inch Aluminum Cover Black W Load Bolts – 40-2013-1ALB
- Black rear cover for Ford 8.8 inch axles, part number 40-2013-1ALB
- Magnetic drain plug and dipstick to isolate debris from moving parts
- Bearing cap support bolts for added strength
- Black powder coat finish with increased fluid capacity
- Also named for Mazda 8.8 inch axles
SKU: G/240-2013-1ALB -
Differential Covers
G2 GM 10.5 Inch 14 Bolt Aluminum Cover – 40-2023AL
- Cast aluminum cover for GM 10.5 inch 14 bolt rear axles
- Reinforcing ribs; heat treated and shot peened for direct impacts
- Designed to dissipate heat and help cool the gear oil
- Part number 40-2023AL, raw aluminum finish
SKU: G/240-2023AL -
Differential Covers
G2 Ford 10.25 Inch/10.5 Inch Aluminum Cover – 40-2046AL
- Rear differential cover for Ford 10.25 inch and 10.5 inch Sterling axles, part number 40-2046AL
- Lightweight cast aluminum body with ribbing
- Heat treated and shot peened casting
- Raw natural aluminum finish
- Listed with extra oil capacity
SKU: G/240-2046AL -
-
-
Axle Upgrade Kits
Trail Gear Samurai Front Axle Service Kit – 141003-3-KIT
- Trail Gear Samurai front axle service kit, part 141003-3-KIT
- One kit covers both left and right front axle sides
- Includes seals, wheel bearings, knuckle bearings and backing plates
- Fits 1986-1995 Samurai models
SKU: TGI141003-3-KIT -
-
-
Differential Covers
G2 Ford 9.75 Inch Aluminum Cover – 40-2012AL
- G2 aluminum differential cover for Ford 9.75 inch rear axles, part number 40-2012AL
- Cast aluminum with reinforcing ribs and a raw natural finish
- Heat treated and shot peened, with a fully machined seal surface
- No vehicle is listed; the cover is built for the axle type
SKU: G/240-2012AL -
-
What belongs in this category
These are the parts that live inside and around the axle housing. Ring and pinion gear sets and installation kits set the final drive ratio. Differentials, including limited-slip and locking units, control how torque is split between the wheels. Axle upgrade kits, axle housing parts, differential covers, ball joints and locking hub spindle nuts round out the group.
The sample listings mention axles such as the Dana 44, Dana 70, Chrysler 8.25 inch and Ford 9.75 inch, so identifying your axle model is the first step.
Choosing a ratio and a differential
Gear ratio should follow tire size and how the vehicle is used. Larger tires effectively raise the overall gearing, which makes the engine work harder and can hurt acceleration and towing. Regearing to a numerically higher ratio restores some of that lost performance. Front and rear ratios must match on a four-wheel-drive vehicle.
- An open differential is the stock choice and offers smooth street manners.
- A limited-slip unit shifts torque toward the wheel with traction while keeping some road manners.
- A locker forces both wheels to turn together for maximum traction on the trail, with some trade-offs in tire wear and handling on pavement.
What to verify before ordering
- Axle model, spline count, bolt pattern and carrier style, because parts differ even within one axle family.
- Tooth count and ratio of the existing gears, which determine whether you need a new matched set.
- Whether a kit includes bearings, shims, seals and hardware or only the gears.
- Front or rear position and side, as parts are often not interchangeable.
Installation notes
Setting up ring and pinion gears requires measuring pinion depth, backlash and bearing preload with the right tools. Mistakes cause noise and premature failure, so many owners leave this job to an experienced drivetrain shop. Ball joints, seals and axle shafts are more approachable but still need proper torque values and clean, correctly lubricated assemblies.
Replace gear oil after installation, follow the break-in procedure from the gear maker, and confirm fitment for your exact year, make and model against the manufacturer's specifications.
Further checks and care
Common mistakes to avoid
Mixing gear sets is a frequent error, since a ring gear and pinion are lapped and matched as a pair. Reusing old bearing races, skipping new shims or ignoring carrier spread can undo an otherwise good build. Another mistake is regearing only one axle. Before you start, gather the correct crush sleeve or shims, thread locker, gear marking compound and the specified gear oil, and keep the work area clean, since grit inside a differential shortens its life.
Measuring and confirming your axle
Beyond the ID tag, confirm the number of ring gear bolts, the carrier bearing style, the axle spline count and the housing width before ordering anything. Record the existing ratio from the tooth counts on the ring gear and pinion, or by counting driveshaft turns for one full wheel rotation. Photos of the cover shape and the axle tube diameter help when comparing against the listing. If a product mentions a specific vehicle platform, confirm it matches yours before proceeding.
Materials, construction and maintenance
Gear sets are usually made from forged alloy steel that is heat treated, and quality depends on tooth pattern accuracy and finishing. Ball joints and bearings rely on correct grease and sealing. After the first few hundred miles of use, change the gear oil to remove break-in metal, then follow the maker's interval. Check axle seals and vent hoses periodically, since a plugged vent can push fluid past seals and contaminate brakes.
Popular Performance Axle Components brands
- G2 Axle and Gear (297)
- Dana Spicer (64)
- Moog (59)
- Crown Automotive (34)
- ARB 4x4 Accessories (33)
- Trail Gear (27)
- Alloy USA (22)
- Eaton (16)
- Motive Gear (15)
- Mag-Hytec (12)
- Omix-Ada (10)
- Dynatrac (9)
Shop Performance Axle Components by type
- Ring and Pinion Installation Kits (216)
- Differential Covers (99)
- Axle Ball Joints (94)
- Axle Upgrade Kits (49)
- Differentials (40)
- Axle Housing (24)
- Hub Gears And Drive Flanges (16)
- Axle King Pin Parts (14)
- Differential Air System Line Fitting (10)
- Differential Air System Line (3)
- Differential Housing (3)
- Carrier Cross Shafts (3)
- Locking Hub Service Kits (1)
- Locking Hub O-Ring (1)
Performance Axle Components FAQ
How do I know which axle I have?
Look for a tag or ID number on the housing, check the cover shape and bolt count, and consult the vehicle's build information. Measuring the ring gear diameter can confirm it. Verify before ordering gears, because many axles look alike.
Do I have to change both front and rear gears together?
On a part-time or full-time four-wheel-drive vehicle, yes. Front and rear ratios must match so the axles turn at the same relative speed, or the driveline can bind and wear out quickly.
Can I install a ring and pinion myself?
It is possible with a dial indicator, torque wrench and the right bearing tools, but correct setup takes experience. Incorrect pinion depth or backlash causes noise and failures, so a professional drivetrain installation is often the safer route.











