Drive Shafts & Drive Shaft Components
Showing 25–36 of 78 resultsSorted by popularity
-
Drive Shafts & Drive Shaft Components
Front Drive Shaft
- Point Spring and Drive Shaft Co. front drive shaft, part number POI5360986
- Stock length, non-CV, no slip yoke eliminator needed
- Fits 4, 6 or 8 cylinder engines and T-4, T-5 and T-170 transmissions
- Fits 1980–1983 Jeep CJ5, 1980–1986 CJ7 and 1981–1985 Scrambler
SKU: POI5360986 -
-
Drive Shaft Universal Joint
Dana Spicer U-Joint – 5-1503X
- Dana Spicer U-joint with a forged cross, lubeable and outside snap ring
- Front driveshaft at the front axle, bearing cap 0.984 inches
- Snap ring diameter 2.517 inches
- Fits 1979–2006 compact trucks and SUVs, including Chevrolet Tracker and Suzuki Samurai
SKU: D/S5-1503X -
Drive Shafts & Drive Shaft Components
Dana Spicer Performance Front Drive Shaft – 10004467
- Dana Spicer performance front driveshaft for the Jeep Wrangler JK
- Tubes about 50 percent thicker than original equipment
- Front driveshaft position
- Fits 2007–2018 Jeep Wrangler JK, 2-door and 4-door
SKU: D/S10004467 -
Drive Shaft Slip Yoke
Dana Spicer Drive Shaft End Yoke – 10049138
- Dana Spicer 1310 series drive shaft end yoke with 32 splines
- BS yoke style that converts the transfer case companion flange
- Original equipment quality from Dana Spicer
- Fits 2007–2018 Jeep Wrangler JK, 2-door and 4-door
SKU: D/S10049138 -
Drive Shafts & Drive Shaft Components
Dana Spicer Drive Shaft Assembly for Ultimate Dana Spicer 60 JL/JT Front – 10097841
Drive Shafts & Drive Shaft ComponentsDana Spicer Drive Shaft Assembly for Ultimate Dana Spicer 60 JL/JT Front – 10097841
- Dana Spicer front driveshaft assembly for the Ultimate Dana 60 JL and JT front axle
- 1350 series driveshaft with thicker tubing and a transfer case slip assembly
- All hardware included for a bolt-in fit
- Fits 2018–2026 Jeep Wrangler JL and 2020–2026 Jeep Gladiator
SKU: D/S10097841 -
Drive Shafts & Drive Shaft Components
Dana Spicer Drive Shaft Assembly for Ultimate Dana 60 – 10113217
Drive Shafts & Drive Shaft ComponentsDana Spicer Drive Shaft Assembly for Ultimate Dana 60 – 10113217
- Dana Spicer rear driveshaft assembly for the Ultimate Dana 60
- 1350 series driveshaft with extra thick tubing
- Slip assembly at the transfer case for impact and contamination protection
- All hardware included for a bolt-in fit; fits 2007–2018 Jeep Wrangler JK
SKU: D/S10113217 -
Drive Shaft Slip Yoke
Dana Spicer Differential End Yoke – 10025494
- Dana Spicer differential end yoke for Dana 60 and Dana 70 axles
- 29 splines, 1350 series, U-bolt style yoke
- Hub diameter 1.500 inches, centerline to end hub 3.000 inches
- Fits full-size vans and trucks listed from 1982 through 2015
SKU: D/S10025494 -
Drive Shaft Universal Joint
Dana Spicer Detroit 7260 to 1310 Series Cross Over U-Joint – 5-788X
- Dana Spicer Detroit 7260 to 1310 series cross over U-joint
- Converts a 7260 series joint to a 1310 series joint
- Non-greasable with inside and outside snap rings
- Front driveshaft at the front axle; fits Jeep XJ and ZJ and Dodge Dakota
SKU: D/S5-788X -
Drive Shaft Universal Joint
Dana Spicer 1480 Series U-Joint – 5-188X
- Dana Spicer 1480 series U-joint with a forged cross and grease fittings
- Rear driveshaft at the rear axle position
- Outside snap ring, 1.375-inch bearing cap diameter and 4.188-inch snap ring diameter
- Fits heavy-duty Chevrolet, GMC, Ford and Dodge 2500 and 3500 trucks and vans
SKU: D/S5-188X -
Drive Shaft Universal Joint
Dana Spicer 1310WJ Series Blue-Coated Universal Joint – 5-760XC
- Dana Spicer 1310 series blue-coated universal joint with SPL 30 and 1350 snap ring
- Blue coating on a non-greasable U-joint kit
- Front axle at the wheels, for many Ford, Dodge, GMC, Chevrolet and Jeep models
- Blue coating rated for 45 hours in a mud bath
SKU: D/S5-760XC
What this category includes
A drive shaft is a rotating tube with a joint at each end that transmits torque while the suspension moves. On a 4x4 you have a front and a rear shaft. This category lists complete shafts as well as the pieces that wear out or that change when you lift the vehicle: universal joints, CV boots, slip yokes, pinion yokes, strap kits, bolts and yoke conversion kits.
When to replace or upgrade
Common triggers are a vibration at highway speed, a clunk when shifting between drive and reverse, or grease slung from a torn boot. Worn U-joints can often be replaced alone, but a bent shaft or damaged tube needs replacement. After a lift, factory shafts may run at steep angles or lack the length to handle extra travel, so a longer or CV-style shaft is a common upgrade.
- Stock-length replacement: For worn shafts on unmodified or mildly modified vehicles.
- Extended or high-angle CV shafts: Built for lifted vehicles with greater angles.
- Heavy-duty U-joint series: Larger joints for stronger axles and hard use.
Specs to compare
Match the position, front or rear, and the transmission type, since manual and automatic builds often use different lengths. Check the joint series, such as 1310 or 1350, which refers to the U-joint size and must suit the axle and transfer case yokes. Look at whether the shaft is a CV (constant velocity) design and whether a slip yoke eliminator is required, because some rear CV shafts need a conversion. Note the lift range listed on the product if one is given.
Installation and balance notes
Mark the shaft and flange positions before disconnecting so the phasing returns to the same orientation. Torque the yoke bolts and straps to the manufacturer's specification, and grease serviceable U-joints if they have fittings. Drive shafts spin at high speed, so an unbalanced or poorly installed unit causes vibration and can fail dangerously. Professional installation is wise if you are changing yokes or a conversion kit.
Check driveline angles after any lift, since matching angles at each joint reduces vibration. Confirm fitment for your exact year, make, model, axle and transmission, and verify against the manufacturer's specifications. Inspect boots, joints and bolts regularly, especially after water crossings.
Maintenance and common mistakes
Inspect the drive shafts at each oil change. Grab each shaft and try to move it at the joints, and any play or clunk suggests a worn U-joint. Check CV boots for tears, since a torn boot lets out grease and lets in dirt, and replace it promptly. Serviceable U-joints with grease fittings should be greased on the schedule given by the manufacturer, using the grease they recommend.
A very common mistake is replacing a shaft and ignoring the cause of the damage, such as a worn transfer case output bushing or steep driveline angles after a lift. Another is installing yokes or shafts without aligning the phasing marks, which causes vibration. Also avoid mixing joint series, because a 1310 joint will not fit a yoke made for a 1350 or 1480.
After water crossings, check for water contamination in joints, and re-grease where possible. Before a trip, look at the bolts and straps, since vibration can loosen them. If a vibration appears after an install, stop and diagnose it rather than driving on it.
Popular Drive Shafts & Drive Shaft Components brands
- Dana Spicer (37)
- Crown Automotive (8)
- G2 Axle and Gear (7)
- TeraFlex (5)
- J.E. Reel (5)
- Rough Country (5)
- Trail Gear (3)
- Omix-Ada (3)
- All German Motorsports (3)
- Rubicon Express (1)
- Point Spring And Drive Shaft Co. (1)
Shop Drive Shafts & Drive Shaft Components by type
Drive Shafts & Drive Shaft Components FAQ
What causes drive shaft vibration?
Common causes are worn U-joints, a bent or unbalanced shaft, a lift that creates steep angles, or loose hardware. Inspect joints for play, check angles and bolts, and replace damaged parts rather than ignoring the vibration.
What is a slip yoke eliminator?
It replaces the sliding yoke on the transfer case output with a fixed yoke, which pairs with a CV rear shaft that handles length changes. Some CV shafts require it, as listed in the product notes.
Can I replace just the U-joints?
Often yes, if the shaft tube and yokes are straight and undamaged. U-joints are pressed in or held with clips, so some tools are needed. A bent or out-of-balance shaft should be replaced.
Do I need a new drive shaft after a lift?
Not always on mild lifts, but taller lifts often change length and angle enough to need a longer or CV shaft. Check the manufacturer's recommendations for your lift height and driveline.









