Select your vehicle

Driveline Parts

Driveline parts for 4×4 vehicles: drive shafts, universal joints, slip yokes, flange yokes, CV components, bolts, straps and shims. Listings span Crown Automotive, Rubicon Express, Dana Spicer, Rugged Ridge and Pro Comp Suspension, with Omix-Ada and Trail Gear.Pick a subcategory, open a product page for part numbers and details, then compare the listings on this page.

Rubicon Express front CVO drive shaft with 1310 series yoke

Every inch of lift changes the angle your drive shafts run at, and the driveline is where that shows up first as vibration, clunks or a torn boot. This section covers complete shafts and the joints, yokes, hardware and spacers that tie the transfer case to the axles.

Complete shafts include CV-style and double-cardan units built for lifted Jeeps and trucks. Joints and yokes are sorted by series, so knowing whether you run 1310 or 1350 parts narrows the list fast. Strap, U-bolt and bolt kits hold the joints in place. Spacers and carrier shims correct angles after a lift, and speedometer gears and seals cover the transfer case output.

181Parts listed
17Brands
16Part types
1310–1410U-joint series
1" / 1.5"Spacer lengths
2.5°Carrier bearing shim

Shop driveline parts by type

Popular driveline parts

U-joint and yoke dimension reference

Spicer-pattern dimensions for the joints and hardware most common on 4x4 drivelines. Measure your old part with calipers and match both numbers before ordering.

U-joint series dimensions

Cap diameterSpan (cap to cap)
13101.062"3.219"
13301.062"3.625"
13501.188"3.625"
14101.188"4.188"
1310/1330 combo1.062" both3.219" x 3.625"

Fixes after a lift

  • Transfer case spacer: 1" or 1.5" 6061-T6 aluminum, with hardware
  • Carrier drop shims realign two-piece rear shafts (2.5° kits listed)
  • CV shaft plus slip yoke eliminator: example 17" collapsed, 21.5" extended
  • GM IFS trucks: CV front shafts that need no slip yoke eliminator
  • JK front: U-bolt yoke conversion to replace straps
  • JK with 3"+ lift: high-angle CV kit for the factory front shaft

Strap and U-bolt kits

Cap sizeBolt spacing
U-bolt kit, 1210/1310/13301.062" small cup1.416" center to center
U-bolt kit, 1350/14101.188" cup1.666" center to center
Strap kit, 1350/14101.187" cap1.806" center to center
Strap kit, 13101.062" small cupFits 1210, 1310 and 1330 yokes

Flange and socket yoke specs

Spicer 1310 flange yoke4.250" bolt circle, 2" female pilot
Currie Ford 8.8 adapter3.50" bolt circle, 2" female pilot
Spicer 1310 CV socket yoke3.218" bolt circle, greasable
Check before orderingBolt circle, pilot diameter, bolt count

NP231 transfer case parts

Speedometer gear32-tooth nylon gear on a steel shaft
Speedometer pinion O-ring6035709, sold separately
Rear output slip yoke1310 joint; XJ, ZJ, WJ and TJ
Slip yoke bootNP231 or NP242 equipped Jeeps
Front shaft bolt6036415AA, sold each

Drive shafts are safety-critical rotating parts. Mark the shaft before removal, replace one-time-use bolts, and have a new or modified shaft balanced before driving at speed.

All Driveline Parts 182 parts

Showing 1–12 of 182 resultsSorted by popularity

What the driveline includes

The driveline carries power from the transmission and transfer case to the axles. Drive shafts connect the sections, universal joints let them flex as the suspension moves, and slip yokes let the length change. This catalog branch also includes speedometer gears, flange and pinion yokes, strap and bolt kits, boots, shims and support bearings.

Parts and when you need them

Common reasons to shop this category include the following.

  • Vibration or clunking at speed, often from worn universal joints or a bent shaft
  • Lift kits that change driveshaft angles and call for a CV-style shaft or a spacer or shim
  • Torn boots or a worn slip yoke that lets in dirt and loses grease
  • Conversion of a pinion yoke from straps to a U-bolt design
  • Broken strap or bolt hardware at a transfer case or axle yoke

Choosing the right part

U-joint series such as 1310 and 1410 refer to the size of the cap and yoke, so confirm the series before ordering. Shaft listings note front or rear, vehicle model, engine, transmission and axle, and the length. Package sets list dimensions and whether yokes and flanges are included.

After a lift, check driveshaft angles. CV or double-cardan shafts, such as the CVF-style shafts in the sample listings, handle larger operating angles, but they still need correct pinion angle. Heavier-duty parts matter if you run big tires or add a locker.

Installation and balance

Mark the drive shaft position before removal so it returns in phase, and support it so it does not hang from a joint. Torque bolts and straps to the manufacturer's specifications. Use threadlocker only where specified.

Grease any serviceable joints and slip yokes at the interval in your manual. A vibration after installation can come from a wrong angle or an unbalanced shaft, and drivelines are safety-critical rotating assemblies, so consider professional installation and balancing if you have any doubt.

Keep an eye on your service intervals. Drive shaft joints, slip yokes and support bearings that are greased on schedule last far longer, and a quick look for dried grease, rust-colored dust at the cap or play in a joint can catch problems before a breakdown on the trail.

Inspection, angles and avoiding vibration

Driveline vibration is one of the most common complaints on modified 4x4s, and it is usually caused by angles rather than by a defective part. For a standard two-joint shaft, the angles at both ends should be close to equal and opposite, and ideally small. A lift, a transfer case drop or a change in axle position can change them. Measuring with an angle finder at ride height gives a good baseline.

  • Inspect U-joints for play by twisting the shaft, and replace any that feel notchy or loose
  • Look for rust-colored dust at the caps, which signals dry or failing joints
  • Check that the slip yoke has enough engagement in the transmission or transfer case at full droop
  • Make sure the shaft is not rubbing on the skid plate, crossmember or exhaust at full compression
  • Verify the flange yokes and companion flanges are clean and flat, and use the correct bolts

Mistakes to avoid include running worn joints on a new shaft, reusing damaged strap bolts and ignoring a small vibration. A shaft that has been dented, or that has lost a balance weight, can shake the whole vehicle. If a vibration appears only at a certain speed, note it and have the shaft balanced, since driveline failures at highway speed can be dangerous.

Popular Driveline Parts brands

Driveline Parts FAQ

How can I tell if my U-joints are worn?

Symptoms include clunking when shifting between drive and reverse, vibration that rises with speed and visible play when you twist the shaft by hand. Replace them in sets for even wear.

Do I need a new drive shaft after a lift?

Often an adjustment is enough, but larger lifts can push angles beyond what a standard shaft handles. A CV or double-cardan design, spacers or shims may be needed, so check the manufacturer's guidance.

What do 1310 and 1350 mean for U-joints?

They are series numbers that describe the joint's size and strength. Match the series to the yoke on your shaft, since different series are not interchangeable.

Why does my driveshaft vibrate?

Common causes are worn U-joints, a bent or unbalanced shaft, wrong pinion angle after a lift and worn slip yokes. Inspect each in turn, then have balance checked if it persists.