Select your vehicle
-13%

G2 Axle and Gear 1350 JL Sport A/T 2 Dr Rear Drive Shaft – 92-2149-2

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • G2 Axle and Gear 92-2149-2 rear driveshaft for automatic Wrangler JL 2-door Sport
  • Extended length CV design with solid body 1350 series u-joints
  • Heavy duty D.O.M. tubing, dynamically balanced
  • No slip yoke eliminator required
  • Fits 2018–2020 Jeep Wrangler JL 2-door Sport and Sport S

Description

Overview

The 92-2149-2 is an extended length CV rear driveshaft for the 2018–2020 Jeep Wrangler (JL) 2-door Sport and Sport S with an automatic transmission. It is a direct fit for those models.

G2 markets its 1350 JL driveshafts as heavy duty 1 ton upgrades for both the front and rear of the JL. This rear shaft is built with heavy duty D.O.M. tubing for strength, solid body 1350 series u-joints for durability, and a dynamic balance that the company says eliminates vibration.

No slip yoke eliminator is needed, so the shaft can be installed without one. Because it is extended length, confirm the fit against your transmission output and rear axle before ordering.

Key features

  • Rear position for the Wrangler JL 2-door Sport models
  • Automatic transmission application
  • Heavy duty D.O.M. tubing
  • Solid body 1350 series u-joints
  • CV joint design
  • Dynamically balanced for smooth running
  • Extended length

Rear driveline basics

The rear driveshaft transfers torque from the transmission output to the rear axle pinion, and it has to handle changing angles as the rear suspension moves. Extended length helps set those angles on a lifted or extended setup, but the length must match the transmission output and pinion position. Small errors show up as vibration, so measure carefully and confirm the joint angles before the vehicle goes back on the trail.

Rear shafts wear the same way front shafts do. Joint play, a bent tube or an unbalanced shaft can cause a vibration that rises with speed, and a clunk when the drivetrain changes load can point to worn joints. Check the joints regularly, keep the balance intact, and have the shaft rebalanced if vibration persists after installation.

  • Measure the length before installing
  • Check joint angles after any lift or axle change
  • Look for debris on balance weights

Specifications

Brand G2 Axle and Gear
Part number 92-2149-2
Position Rear
Transmission type Automatic
Length Extended
Joint type CV
Tubing Heavy duty D.O.M.
U-joints Solid body 1350 series
Slip yoke eliminator Not required
Fitment type Direct fit

Vehicle fitment

It fits the 2018–2020 Jeep Wrangler (JL) 2-door Sport and 2-door Sport S.

Confirm fit for your vehicle’s year, model and trim before ordering, especially for the Unlimited 4-door, the Rubicon and the 2021–2022 Wrangler JL.

What’s included

The rear driveshaft assembly. No separate hardware is supplied with it.

Fitment

VehicleYearsTrims
Jeep Wrangler (JL)2018–2020Sport (2-Door), Sport S (2-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the 92-2149-2 fit a 2019 Jeep Wrangler JL 2-door Sport?

Yes. It fits the 2018–2020 Jeep Wrangler (JL) 2-door Sport and Sport S, so a 2019 2-door Sport is covered. This is the automatic transmission version.

Does this shaft fit the Unlimited 4-door?

No. The rear shaft fits the 2-door Sport and Sport S only, so check your body style before ordering. Confirm your year, model and trim as well, since the 4-door body is not covered.

Does this rear driveshaft need a slip yoke eliminator?

No. The shaft uses CV joints with solid body 1350 series u-joints, and no slip yoke eliminator is required. The extended length should still be checked against the transmission output and rear axle during installation.

Can a rear driveshaft cause vibration when worn?

Yes. A worn joint or an out-of-balance shaft can cause vibration that increases with speed, along with clunks when the drivetrain changes load. Check the joints for play and look for debris on the balance weights, and have the shaft balanced if vibration continues.

Should the rear pinion angle be checked after installing?

Yes. After a driveshaft change, check the pinion angle and joint angles, since suspension and driveline geometry set how the shaft runs. Correct angles reduce vibration and wear on the u-joints over time.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon