Select your vehicle

G2 Axle and Gear 1350 JL Rubicon M/T Front Drive Shaft – 92-2151-1M

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • G2 Axle and Gear 92-2151-1M front driveshaft for manual Wrangler JL Rubicon
  • Extended length CV design with 1350 series u-joints
  • Built from heavy duty D.O.M. tubing and balanced to reduce vibration
  • No slip yoke eliminator required
  • Fits 2018–2020 Jeep Wrangler JL Rubicon, 2-door and Unlimited 4-door

Description

Overview

The 92-2151-1M is a manual transmission front driveshaft for the 2018–2020 Jeep Wrangler (JL) Rubicon. It fits 2-door and Unlimited 4-door models, and it is the manual companion to the automatic 92-2151-1 front shaft.

The shaft is built from heavy duty D.O.M. tubing with solid body 1350 series u-joints in a CV design. It is dynamically balanced to reduce vibration. No slip yoke eliminator is needed to fit it.

The shaft is an extended length part, so check the length against the transfer case and the front axle before installation.

Key features

  • Front position for the Wrangler JL Rubicon
  • Manual transmission application
  • Heavy duty D.O.M. tubing
  • Solid body 1350 series u-joints
  • CV joint design
  • Dynamically balanced
  • Extended length

Manual driveline checks

On a manual Wrangler, the front driveshaft carries torque from the transfer case to the front axle while the suspension moves through its travel. The CV design allows steady rotation through changing angles, but the joint angles at both ends must still be set correctly. A shaft that is too long or too short shifts those angles, which can cause vibration and early wear. Lift height and axle position both affect the result, so measure before installing.

Driveline inspection is a good habit on any front shaft. Check the joints for play, look for grease seepage, and listen for clicks or clunks when turning or shifting. Balance matters too, so any vibration that increases with speed deserves a closer look. Replacing worn joints at the same time as the shaft keeps the driveline working as a matched set.

  • Check joint angles after installation
  • Look for play in the joints by hand
  • Recheck the fit after any suspension change

Specifications

Brand G2 Axle and Gear
Part number 92-2151-1M
Position Front
Transmission type Manual
Length Extended
Joint type CV
Tubing Heavy duty D.O.M.
U-joints Solid body 1350 series
Slip yoke eliminator Not required
Fitment type Direct fit

Vehicle fitment

It fits the 2018–2020 Jeep Wrangler (JL) Rubicon in 2-door and Unlimited 4-door versions.

Confirm fit for your vehicle’s year, model and trim before ordering, especially for 2021–2022 Wrangler JL, Gladiator and Sport models.

Installation notes

No slip yoke eliminator is needed for this front shaft. Check the extended length against the transfer case output and front axle pinion before installing, because a length mismatch would affect the joint angles.

What’s included

The front driveshaft assembly is included, with no separate hardware.

Fitment

VehicleYearsTrims
Jeep Wrangler (JL)2018–2020Rubicon (2-Door), Unlimited Rubicon (4-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the 92-2151-1M fit a 2019 Jeep Wrangler JL Rubicon Unlimited with a manual transmission?

Yes. It fits the 2018–2020 Jeep Wrangler (JL) Rubicon, including the Unlimited 4-door, so a 2019 Unlimited Rubicon with a manual transmission is covered.

How does this manual front shaft differ from the 92-2151-1?

The 92-2151-1M is the manual transmission version, while the 92-2151-1 is the automatic transmission version. Both are extended length CV front shafts with solid body 1350 series u-joints.

Does it require a slip yoke eliminator?

No. A slip yoke eliminator is not required for this shaft. It uses a CV design with solid body 1350 series u-joints, and the extended length should be checked during installation.

What are signs a front driveshaft needs attention?

Look for vibration that rises with speed, clunking when shifting or accelerating, or grease leaking from a joint. Rust, bent tubing and worn u-joints also warrant inspection. Address these early, since a failed joint can damage nearby driveline parts.

Should the u-joints be replaced when the shaft is installed?

Inspect the joints before installation and replace them if they show play, dryness or rust. Many installers replace worn joints together with the shaft so the driveline runs as a matched set with new parts.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon