Select your vehicle
-13%

Rough Country Rear CV Drive Shaft (4-6″ Lift) – 5080.1

Rough Country

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear double cardan CV driveshaft for TJ and YJ lifts
  • Fits 1997–2002 and 2005–2006 Wrangler TJ, 1987–1993 Wrangler YJ
  • Slip yoke eliminator required
  • Not for Rubicon models
  • Part number R/C5080.1

Description

Overview

The Rough Country Rear CV Drive Shaft (4-6 inch lift), part R/C5080.1, is a double cardan style CV driveshaft for lifted Jeep Wrangler models. Rough Country recommends it for TJ models with a 4 to 6 inch suspension lift, and for YJ models with a 4 inch lift, to prevent driveline vibration and breakage of the rear output shaft.

It fits 1997–2002 TJ models with the 2.5L 4-cylinder and 3-speed automatic, and 2005–2006 TJ models with the 2.4L 4-cylinder and 6-speed manual. It does not fit Rubicon models. Confirm fit for your vehicle’s year, model and trim before ordering.

It also fits 1987–1993 Wrangler YJ models with a 4 inch lift. A slip yoke eliminator is required with this shaft.

Key features

  • Double cardan style CV rear driveshaft
  • Recommended for TJ lifts of 4 to 6 inches
  • Recommended for YJ lifts of 4 inches
  • Helps prevent driveline vibration and rear output shaft breakage
  • Extended, direct fit

Driveline angles and lift height

A CV driveshaft works best when the joint angles stay within the range the lift height allows. Raising a Wrangler changes the angle at the axle and transfer case, and that change is what drives vibration. A shaft matched to the lift keeps the joints working within their intended travel, which helps the rear output shaft last longer.

Before buying, confirm the lift height, the engine, the transmission and the model year. A shaft that suits one TJ setup may not suit another. Small changes such as a different transfer case or a new tire size can also affect driveline geometry, so re-check the setup after any of those changes.

After installation, drive at a few speeds and listen for new vibration. Check the joint boots for tears and look for grease leaks. Re-torque the mounting bolts after the first few trail runs, since settling is normal on a new driveline.

  • Confirm lift height and engine/transmission match before buying
  • Check joint boots for tears or grease leaks
  • Re-torque bolts after the first few trail runs

Specifications

Brand Rough Country
Part number R/C5080.1
Position Rear
Joint type CV, double cardan style
Recommended lift 4 to 6 inches (TJ), 4 inches (YJ)
TJ engine and transmission 1997–2002 with 2.5L 4-cylinder and 3-speed automatic; 2005–2006 with 2.4L 4-cylinder and 6-speed manual
Slip yoke eliminator Required
Fitment type Direct fit

Vehicle fitment

It is a rear shaft for the 1997–2002 and 2005–2006 Jeep Wrangler TJ and the 1987–1993 Jeep Wrangler YJ. TJ fitment is limited to the engine and transmission combinations in the specifications.

Rubicon models are excluded, and TJ years and engines outside the two listed combinations are not covered. Confirm your vehicle’s year, model and trim before choosing this part.

Installation notes

A slip yoke eliminator is required, so budget for one with the shaft. Confirm the lift height and the engine and transmission combination for your vehicle before installing.

What’s included

One rear CV driveshaft.

Not included: a slip yoke eliminator, which this shaft requires.

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ)1997–2002, 2005–2006SE
Jeep Wrangler (YJ)1987–1993Base, Islander, Laredo, Renegade, S, Sahara, Sport

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the R/C5080.1 fit a 2000 Jeep Wrangler TJ with a 2.5L four-cylinder?

Yes. It fits a 1997–2002 TJ with the 2.5L four-cylinder and a 3-speed automatic transmission. Other TJ engine and transmission combinations are not covered.

Does this shaft fit a 2005 TJ with the 2.4L engine?

Yes, if the vehicle is a 2005–2006 TJ with the 2.4L four-cylinder and a 6-speed manual transmission. Other combinations are not covered.

Is this shaft for a Rubicon?

No. It does not fit Rubicon models. Check the model before choosing this part, since a match on year alone is not enough.

Is a slip yoke eliminator optional with this shaft?

No. A slip yoke eliminator is required with this shaft. It replaces the slip yoke function of the transfer case, so budget for one with the shaft before installing.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon