Driveline Parts
Showing 25–36 of 182 resultsSorted by popularity
-
Drive Shafts & Drive Shaft Components
G2 Axle and Gear 1350 JL Rubicon A/T Front Drive Shaft – 92-2151-1
Drive Shafts & Drive Shaft ComponentsG2 Axle and Gear 1350 JL Rubicon A/T Front Drive Shaft – 92-2151-1
- G2 Axle and Gear 92-2151-1 front driveshaft for automatic Wrangler JL Rubicon
- Extended length CV driveshaft with solid body 1350 series u-joints
- Heavy duty D.O.M. tubing, dynamically balanced for smooth running
- No slip yoke eliminator required
- Fits 2018–2020 Jeep Wrangler JL Rubicon, 2-door and Unlimited 4-door
SKU: G/292-2151-1 -
Drive Shafts & Drive Shaft Components
Front Drive Shaft
- Point Spring and Drive Shaft Co. front drive shaft, part number POI5360986
- Stock length, non-CV, no slip yoke eliminator needed
- Fits 4, 6 or 8 cylinder engines and T-4, T-5 and T-170 transmissions
- Fits 1980–1983 Jeep CJ5, 1980–1986 CJ7 and 1981–1985 Scrambler
SKU: POI5360986 -
Drive Shafts & Drive Shaft Components
Dana Spicer Performance Front Drive Shaft – 10004467
- Dana Spicer performance front driveshaft for the Jeep Wrangler JK
- Tubes about 50 percent thicker than original equipment
- Front driveshaft position
- Fits 2007–2018 Jeep Wrangler JK, 2-door and 4-door
SKU: D/S10004467 -
Drive Shaft Slip Yoke
Dana Spicer Drive Shaft End Yoke – 10049138
- Dana Spicer 1310 series drive shaft end yoke with 32 splines
- BS yoke style that converts the transfer case companion flange
- Original equipment quality from Dana Spicer
- Fits 2007–2018 Jeep Wrangler JK, 2-door and 4-door
SKU: D/S10049138 -
Drive Shafts & Drive Shaft Components
Dana Spicer Drive Shaft Assembly for Ultimate Dana Spicer 60 JL/JT Front – 10097841
Drive Shafts & Drive Shaft ComponentsDana Spicer Drive Shaft Assembly for Ultimate Dana Spicer 60 JL/JT Front – 10097841
- Dana Spicer front driveshaft assembly for the Ultimate Dana 60 JL and JT front axle
- 1350 series driveshaft with thicker tubing and a transfer case slip assembly
- All hardware included for a bolt-in fit
- Fits 2018–2026 Jeep Wrangler JL and 2020–2026 Jeep Gladiator
SKU: D/S10097841 -
Drive Shafts & Drive Shaft Components
Dana Spicer Drive Shaft Assembly for Ultimate Dana 60 – 10113217
Drive Shafts & Drive Shaft ComponentsDana Spicer Drive Shaft Assembly for Ultimate Dana 60 – 10113217
- Dana Spicer rear driveshaft assembly for the Ultimate Dana 60
- 1350 series driveshaft with extra thick tubing
- Slip assembly at the transfer case for impact and contamination protection
- All hardware included for a bolt-in fit; fits 2007–2018 Jeep Wrangler JK
SKU: D/S10113217 -
Drive Shaft Slip Yoke
Dana Spicer Differential End Yoke – 10025494
- Dana Spicer differential end yoke for Dana 60 and Dana 70 axles
- 29 splines, 1350 series, U-bolt style yoke
- Hub diameter 1.500 inches, centerline to end hub 3.000 inches
- Fits full-size vans and trucks listed from 1982 through 2015
SKU: D/S10025494 -
Drive Shaft Boot
Crown Automotive Drive Shaft Boot – 5083001AA
- Crown Automotive drive shaft boot, part number 5083001AA
- Covers 2007–2018 Jeep Wrangler JK 2-door rear driveshafts
- Also fits the 2003–2006 Jeep Wrangler TJ, 2005–2007 Jeep Liberty KJ and Dodge and Ram 1500 trucks
- TJ/LJ front driveshaft boot will not fit the Rubicon package
SKU: CRO5083001AA -
Drive Shaft Spacer
Trail Gear Longfield Driveline Spacer – 301697-1-KIT
- Trail Gear driveline spacer kit for a driveshaft that is too short after a lift
- 1 inch and 1.5 inch spacer sizes, with bolts
- Part number 301697-1-KIT, UPC 700006929981
- Universal fit; year, model and trim to be confirmed
SKU: TGI301697-1-KIT
What the driveline includes
The driveline carries power from the transmission and transfer case to the axles. Drive shafts connect the sections, universal joints let them flex as the suspension moves, and slip yokes let the length change. This catalog branch also includes speedometer gears, flange and pinion yokes, strap and bolt kits, boots, shims and support bearings.
Parts and when you need them
Common reasons to shop this category include the following.
- Vibration or clunking at speed, often from worn universal joints or a bent shaft
- Lift kits that change driveshaft angles and call for a CV-style shaft or a spacer or shim
- Torn boots or a worn slip yoke that lets in dirt and loses grease
- Conversion of a pinion yoke from straps to a U-bolt design
- Broken strap or bolt hardware at a transfer case or axle yoke
Choosing the right part
U-joint series such as 1310 and 1410 refer to the size of the cap and yoke, so confirm the series before ordering. Shaft listings note front or rear, vehicle model, engine, transmission and axle, and the length. Package sets list dimensions and whether yokes and flanges are included.
After a lift, check driveshaft angles. CV or double-cardan shafts, such as the CVF-style shafts in the sample listings, handle larger operating angles, but they still need correct pinion angle. Heavier-duty parts matter if you run big tires or add a locker.
Installation and balance
Mark the drive shaft position before removal so it returns in phase, and support it so it does not hang from a joint. Torque bolts and straps to the manufacturer's specifications. Use threadlocker only where specified.
Grease any serviceable joints and slip yokes at the interval in your manual. A vibration after installation can come from a wrong angle or an unbalanced shaft, and drivelines are safety-critical rotating assemblies, so consider professional installation and balancing if you have any doubt.
Keep an eye on your service intervals. Drive shaft joints, slip yokes and support bearings that are greased on schedule last far longer, and a quick look for dried grease, rust-colored dust at the cap or play in a joint can catch problems before a breakdown on the trail.
Inspection, angles and avoiding vibration
Driveline vibration is one of the most common complaints on modified 4x4s, and it is usually caused by angles rather than by a defective part. For a standard two-joint shaft, the angles at both ends should be close to equal and opposite, and ideally small. A lift, a transfer case drop or a change in axle position can change them. Measuring with an angle finder at ride height gives a good baseline.
- Inspect U-joints for play by twisting the shaft, and replace any that feel notchy or loose
- Look for rust-colored dust at the caps, which signals dry or failing joints
- Check that the slip yoke has enough engagement in the transmission or transfer case at full droop
- Make sure the shaft is not rubbing on the skid plate, crossmember or exhaust at full compression
- Verify the flange yokes and companion flanges are clean and flat, and use the correct bolts
Mistakes to avoid include running worn joints on a new shaft, reusing damaged strap bolts and ignoring a small vibration. A shaft that has been dented, or that has lost a balance weight, can shake the whole vehicle. If a vibration appears only at a certain speed, note it and have the shaft balanced, since driveline failures at highway speed can be dangerous.
Popular Driveline Parts brands
- Crown Automotive (32)
- Rubicon Express (27)
- Rugged Ridge (24)
- Dana Spicer (17)
- Pro Comp Suspension (14)
- G2 Axle and Gear (13)
- Trail Gear (12)
- Omix-Ada (10)
- J.E. Reel (7)
- TeraFlex (5)
- Rough Country (5)
- Fabtech (5)
Shop Driveline Parts by type
- Drive Shafts (85)
- Speedometer Drive Gear (34)
- Drive Shaft Spacer (12)
- Universal Joint U-Bolt Kit (10)
- Drive Shaft Shim Kit (6)
- Drive Shaft Boot (6)
- Driveshaft Flange Yoke (6)
- Universal Joint Strap Kit (5)
- Drive Shaft Slip Yoke (5)
- Driveshaft Bolt (3)
- Drive Shaft CV Joint Repair Kit (3)
- Driveshaft CV Socket Yoke Assembly (2)
- Drive Line Bearings (2)
- Drive Shaft Pinion Yoke Conversion Kit (2)
- Drive Shaft Slip Yoke Felt (1)
Driveline Parts FAQ
How can I tell if my U-joints are worn?
Symptoms include clunking when shifting between drive and reverse, vibration that rises with speed and visible play when you twist the shaft by hand. Replace them in sets for even wear.
Do I need a new drive shaft after a lift?
Often an adjustment is enough, but larger lifts can push angles beyond what a standard shaft handles. A CV or double-cardan design, spacers or shims may be needed, so check the manufacturer's guidance.
What do 1310 and 1350 mean for U-joints?
They are series numbers that describe the joint's size and strength. Match the series to the yoke on your shaft, since different series are not interchangeable.
Why does my driveshaft vibrate?
Common causes are worn U-joints, a bent or unbalanced shaft, wrong pinion angle after a lift and worn slip yokes. Inspect each in turn, then have balance checked if it persists.








