Select your vehicle

J.E. Reel 1310 Replacement Front Drive Shaft – 31JK-OE-24F

J.E. Reel

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Replacement front shaft for 2007–2011 Jeep Wrangler JK Unlimited
  • Heavy-duty 1310 series, designed for tires up to 35 inches
  • Stock length, non-CV design
  • No slip yoke eliminator required
  • Part number JER31JK-OE-24F

Description

Overview

The J.E. Reel 1310 Replacement Front Drive Shaft, part JER31JK-OE-24F, is a stock-length front driveshaft for the 2007–2011 Jeep Wrangler JK Unlimited. The 1310 series is a heavy-duty upgrade over the original part and is intended for JK owners running tires up to 35 inches for mild use.

This is a non-CV design at stock length, so it replaces the original front shaft without changing the driveline’s overall length. No slip yoke eliminator is required.

Key features

  • Heavy-duty 1310 series front shaft
  • Designed for tires up to 35 inches for mild use
  • Stock length, direct replacement
  • Non-CV joint design
  • No slip yoke eliminator required

Front driveline wear and replacement

The front shaft carries power to the front axle when the vehicle is in four-wheel drive, so it sees steady torque and the angle changes of steering and suspension travel. Inspect the U-joint caps, boots and yokes for play or grease loss, and check for bent tubing after rock strikes or hard landings. Vibration at speed or a clicking through turns can point to a worn joint.

A non-CV front shaft at stock length keeps the original driveline geometry, so replacement is mostly a matter of matching the bolt pattern, yokes and clamp points. Before fitting, clean the pinion and transfer case flanges and replace worn seals or fasteners during the same job. Re-check fastener torque after the first few drives.

  • Check U-joints for play
  • Inspect yokes and flanges before fitting
  • Look for bent tubing after impacts
  • Replace worn seals in the same job

Specifications

Brand J.E. Reel
Part number JER31JK-OE-24F
Position Front
Length Stock
Joint type Non-CV
Slip yoke eliminator Not required
Fitment type Direct fit

Vehicle fitment

This front shaft fits the 2007–2011 Jeep Wrangler (JK) Unlimited four-door models.

Two-door JK models and 2012–2018 JK models need separate fit checks. Confirm your vehicle’s year, model and trim before choosing this part.

What’s included

One front driveshaft assembly.

Fitment

VehicleYearsTrims
Jeep Wrangler (JK)2007–2011Unlimited 70th Anniversary (4-Door), Unlimited Rubicon (4-Door), Unlimited Sahara (4-Door), Unlimited Sport (4-Door), Unlimited X (4-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the JER31JK-OE-24F fit a 2008 Jeep Wrangler JK Unlimited?

Yes. 2008 falls within the 2007–2011 range for the four-door Jeep Wrangler JK Unlimited, and the shaft is intended for the front position on those models.

Is this shaft a CV driveshaft?

No. It is a non-CV design at stock length, so it replaces the original front shaft without a CV joint at the ends.

What size tires is this front driveshaft designed for?

It is designed for tires up to 35 inches for mild use. Heavier use or larger tires should be checked with the manufacturer before installation.

Do I need to replace the front U-joints when I replace the shaft?

Usually it is a good idea to inspect them first. If the joints show play, dry caps or grease loss, replacing them during the same job avoids a second teardown. Check the yokes for wear as well before installing the new shaft.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon