Replacement brake hoses and braided lines for lifted Jeeps and trucks, including stainless steel kits sized for extended suspension travel. Stock hoses can be too short once the axle drops or the vehicle is lifted. Skyjacker, Crown Automotive, Rock Krawler, Rough Country and TeraFlex appear here. Check lift height ranges and fitment on each product page, then compare the products below.
Brake Hose
Showing 1–12 of 165 resultsSorted by popularity
-
Brake Hose
Baer Brakes 21.5 Inch Long Braided Hose Set With 3AN Female Straight X 10Mm 20 Degrees Banjo Ends – 6800501
Brake HoseBaer Brakes 21.5 Inch Long Braided Hose Set With 3AN Female Straight X 10Mm 20 Degrees Banjo Ends – 6800501
- Baer Brakes 6800501: a 21.5-inch braided brake hose set with a 3AN female straight end and a 10 mm banjo end at 20 degrees.
- Two hoses per set, packaged as a pair, with a Teflon liner and DOT approved construction.
- Attaches directly to an OE hard line; crush washers are not included.
- Confirm fit for your vehicle’s year, model and trim before ordering.
SKU: 6800501-BKCZ -
Brake Hose
Baer Brakes 23 Inch Long Braided Hose Set With 3AN Female Straight X 10Mm 20 Degrees Banjo Ends – 6800502
Brake HoseBaer Brakes 23 Inch Long Braided Hose Set With 3AN Female Straight X 10Mm 20 Degrees Banjo Ends – 6800502
- Baer Brakes 6800502: a 23-inch steel braided brake hose set with a 3AN female straight end and a 10 mm banjo end at 20 degrees.
- Packaged as two hoses per set, each attaching directly to an OE hard line.
- Stainless steel hose material with a Teflon liner, DOT approved.
- Confirm fit for your vehicle’s year, model and trim before ordering.
SKU: 6800502-BKCZ -
Brake Hose
Baer Brakes 25.25 Inch Long Braided Hose Set With 3AN Female Straight X 10Mm 20 Degrees Banjo Ends – 6800503
Brake HoseBaer Brakes 25.25 Inch Long Braided Hose Set With 3AN Female Straight X 10Mm 20 Degrees Banjo Ends – 6800503
- Baer Brakes 6800503 is a 25.25 inch braided brake hose set
- 3AN female straight end and 10mm, 20 degree banjo end
- Two stainless steel braided hoses supplied as a pair
- DOT approved, Teflon-lined, attaches to OE hard line
- Crush washers not included; fitment not listed
SKU: 6800503-BKCZ -
Brake Hose
Baer Brakes 3/8-24 Inverted Flare Hard Lines For 15/16 Inch Or 1 Inch Bore Master Cylinders To Proportioning Valve – 6801312
Brake HoseBaer Brakes 3/8-24 Inverted Flare Hard Lines For 15/16 Inch Or 1 Inch Bore Master Cylinders To Proportioning Valve – 6801312
- Two stainless steel inverted flare hard lines with 3/8-24 inch proportioning outlet fittings
- For Baer Remaster master cylinders with a 15/16 inch or 1 inch bore
- Connects a Baer Remaster proportioning valve to a Remaster master cylinder
- Fits left and right port configurations; set includes four tube nuts
SKU: 6801312-BKCZ -
Brake Hose
Baer Brakes 3/8-24 Inverted Flare Hard Lines For 15/16 Inch Or 1 Inch Bore Master Cylinders To General Fit Proportioning Valve – 6801313
Brake HoseBaer Brakes 3/8-24 Inverted Flare Hard Lines For 15/16 Inch Or 1 Inch Bore Master Cylinders To General Fit Proportioning Valve – 6801313
- Connects a Baer ReMaster master cylinder to the Baer general fit proportioning valve, part number 2000035
- Stainless steel inverted flare hard line with a 3/8-24 proportioning outlet port
- Fits 15/16 inch and 1 inch bore ReMaster master cylinders, left and right port
- Includes one hard line and two tube nuts with mounting hardware
- Fitment not listed; Baer part number 6801313
SKU: 6801313-BKCZ -
Brake Hose
Baer Brakes Remaster To Remaster Prop Valve Hardlines Baer 1-1/8 Inch Remaster – 6801318
- Baer Brakes 6801318 polished stainless banjo hard line kit for 1-1/8 inch Remaster
- Two pre-formed lines, four banjo bolts and eight copper crush washers
- Connects a Remaster master cylinder to a Remaster proportioning valve
- Fits left and right port Remaster configurations
- No vehicle fitment listed; match by bore size and valve type
SKU: 6801318-BKCZ -
Brake Hose
Baer Brakes 3/8-24 Inverted Flare Hard Lines For 1-1/8 Inch Bore Master Cylinders To Proportioning Valve – 6801319
Brake HoseBaer Brakes 3/8-24 Inverted Flare Hard Lines For 1-1/8 Inch Bore Master Cylinders To Proportioning Valve – 6801319
- Baer Brakes 6801319 stainless steel inverted flare hard lines, 3/8-24 proportioning outlet
- Connects a Baer 1-1/8 inch Remaster master cylinder to a Remaster proportioning valve
- Works with left and right port Remaster cylinders
- Pair of pre-formed lines with four tube nuts included
- Listed as not DOT approved
SKU: 6801319-BKCZ -
-
-
What a brake hose does
Brake fluid travels to each wheel through steel hard lines on the frame, but the wheels move with the suspension, so a flexible hose links the hard line to the caliper. This hose has to handle high pressure, heat and constant flexing, so it is a safety-critical part of the braking system.
Why lifted vehicles need longer hoses
When you lift a vehicle or add longer-travel suspension, the axle sits farther from the frame, and at full droop a short factory hose can be stretched tight. A stretched hose may fail, pull at the fitting or even limit travel. Extended-length hoses give extra slack, and many are sized to a lift range, such as 4 to 6 inches. Choose the range that matches your lift, and check clearance at full droop and full lock.
Rubber versus braided stainless
- Rubber hoses are the original design and are quiet and economical, but they can swell slightly under pressure, which can soften pedal feel.
- Braided stainless lines have a sheath over an inner liner, resist swelling, and give a firmer pedal. They also resist abrasion from brush and trail debris.
Look for hoses with an inner liner that resists brake fluid. Fittings should match your calipers and hard lines, whether banjo, inverted flare or another type, and may need new crush washers.
Installation and bleeding
Support the vehicle safely and keep brake fluid off paint, since it damages finishes. Replace the hoses on both sides at the same time, and make sure the hose is not twisted when you tighten the fittings. Route the hose so it avoids sharp edges, exhaust parts and tires. After installation the system must be bled to remove air, and the pedal should be firm before driving. Brakes are critical to safety, so have a professional install or inspect the work if you lack experience, and test at low speed before heading out.
Check legal and fitment details
Confirm fitment for your exact year, make and model, including whether it has ABS and what lift you have. Check the manufacturer's specifications, and note that DOT requirements apply to brake hoses, so look for DOT-compliant products.
Inspection and maintenance
Inspect brake hoses at every service. Look for cracks, bulges, rubbing marks and fluid seepage at the ends. Flex the hose by hand while looking for splits. Check the clearance to tires, sway bar links and axle parts at both full droop and full compression, and with the steering at full lock. Use a hose clip or bracket as intended so the hose does not hang loose. Replace brake fluid on the schedule in your owner's manual, since old fluid corrodes the system from within. Never reuse crush washers, and never use a hose that is longer than needed if it can sag or contact the tire.
Flexible hoses age even when they look fine, so many shops recommend replacing them at intervals set by the vehicle maker or when they show any damage, especially on vehicles that see heat, salt or heavy off-road use.
Popular Brake Hose brands
- Skyjacker (34)
- Pro Comp Suspension (30)
- Crown Automotive (29)
- Rubicon Express (24)
- Rugged Ridge (12)
- Omix-Ada (9)
- Baer Brakes (7)
- TeraFlex (5)
- Goodridge (5)
- Rock Krawler (3)
- Dorman (3)
- RT Off-Road (3)
Brake Hose FAQ
Do I need new brake hoses after a lift?
Often yes, especially with lifts of a few inches or more. Factory hoses may be too short at full droop. Many lift kits include them or recommend them, so check the lift manufacturer's instructions.
Are stainless braided brake lines better?
They resist swelling, so the pedal often feels firmer, and the braid protects against abrasion. Rubber hoses are adequate for stock use. Whichever you pick, choose a length that suits your lift and a DOT-compliant product.
Do I need to bleed the brakes after replacing hoses?
Yes. Opening the hydraulic system lets air in, which makes the pedal soft. Bleed all affected calipers according to the vehicle's procedure, and confirm a firm pedal before driving.





