Transfer Case Yoke under Transfer Case Parts covers the output yokes, slip yokes and flanges that connect a transfer case to the driveshafts. Crown Automotive and Omix-ADA supply factory-style 1310 series front yokes and rear slip yokes for the NP207, NP231 and NP241 on the YJ, TJ, XJ and JK, plus 10 spline yokes for the Dana 18 and 20 in vintage Jeeps; Rubicon Express, Advance Adapters and Dana Spicer add CV yokes, flange adapters and fixed yoke kits for driveline upgrades. Match series and spline count below.
Transfer Case Yoke
Showing 1–12 of 20 resultsSorted by popularity
-
Transfer Case Yoke
Trail Gear Suzuki To Toyota Driveline Adapter Yoke – 100116-3-KIT
- Fits 1986–1995 Suzuki Samurai (Base, JA, JL, JS, JX, JX SE)
- Bolts a stock Samurai driveline to a Toyota axle or transfer case
- Covers 1986–89 and 1990–95 Samurai drive shaft patterns
- Trail Gear part number 100116-3-KIT, UPC 70000621219
SKU: TGI100116-3-KIT -
-
Transfer Case Yoke
Omix-ADA Quadratrac Front Output Yoke – 18678.05
- Fits 1976–1979 Jeep CJ7 in Base, Golden Eagle and Renegade trims
- 26 spline front output yoke for Model 300 transfer case CJ drive shafts
- Also fits Atlas transfer cases with 26 spline front output shaft
- Omix-Ada part number 18678.05, UPC 804314044978
SKU: OAI18678.05 -
-
-
-
What the yoke does
The transfer case yoke is the forged steel piece on each output shaft that the driveshaft bolts or clips to. A fixed yoke splines onto the shaft and holds the U-joint with straps or U-bolts. A slip yoke slides over a splined output shaft and lets the driveshaft change length as the axle moves, sealed by the tailhousing seal. A flange, used on the NP241 in the JK and on many later vehicles, bolts to a matching flange on the driveshaft and takes the slip joint out of the transfer case entirely. Each design has a U-joint series, a spline count and a seal diameter that must match both the transfer case and the driveshaft.
Identifying what you have
- Transfer case model: stamped on the round tag on the rear of the case. NP207, NP231 and NP242 appear on the YJ, XJ and TJ; NP241 on the JK; NP203 and NP205 on full-size GM, Ford and Dodge trucks; Dana 18 and Dana 20 on 1946 to 1979 Jeeps.
- Spline count: 26 splines on the NP231 front output, 10 splines on the Dana 18 and 20, 32 splines on the Advance Adapters NP242J fixed yoke kit's new output shaft. Count them or check the model's data.
- U-joint series: 1310 is the common light-duty size with a 3.219 inch cap-to-cap width; 1330, 1350 and 1410 are progressively larger. The yoke must match the driveshaft's U-joint.
- Retention style: strap and bolt on most Jeep yokes, U-bolt on vintage Dana 18 and 20 yokes, bolted flange on the NP241 and on Rubicon Express's billet aluminum adapter.
- Slinger: a steel dust shield on some yokes; a listing will say with or without slinger, and the seal differs.
Replacement versus upgrade
Factory-style yokes from Crown Automotive, Omix-ADA and Jeep, such as the NP231 front output yoke for the 1996 to 2006 XJ, TJ, Dakota and Durango or the NP241 yoke for the 2007 to 2017 JK, replace a yoke whose U-joint saddles are worn or whose seal surface is grooved. Upgrades change the design. A CV yoke, like the Advance Adapters 1350 CV yoke assembly, accepts a double-cardan driveshaft to fix the vibration a lifted Jeep gets from a steep rear driveshaft angle. A fixed yoke kit, such as the NP242J kit with a new output shaft, tailhousing and yoke, eliminates the slip yoke so a longer driveshaft with its own slip joint can be fitted, which stops the transfer case from pumping fluid out when the shaft pulls out during articulation and lets the case be clocked higher. Rubicon Express's front yoke and rear flange adapter are made for its CV driveshafts on the JK.
Installation notes
Mark the yoke and shaft before removal to keep driveline phasing, replace the tailhousing seal whenever a slip yoke comes off, and torque the yoke nut on a fixed yoke to the manufacturer's specification with new thread locker. Lightly polish the seal surface of a used slip yoke and check it for grooves; a grooved yoke eats new seals. Use new U-joint straps or U-bolts and torque them evenly. After installation, drive at highway speed and listen for vibration, which points to phasing or angle problems. Driveline work affects safety; if you are unsure about angles or phasing, have a driveline shop check it. Confirm transfer case model, spline count and U-joint series before choosing.
Popular Transfer Case Yoke brands
- Omix-Ada (5)
- Crown Automotive (5)
- Rubicon Express (3)
- Advance Adapters (2)
- Jeep (2)
- Dana Spicer (1)
- Trail Gear (1)
- TeraFlex (1)
Transfer Case Yoke FAQ
How do I know which U-joint series my yoke is?
Measure the distance between the outside faces of the U-joint caps when installed in the yoke. About 3.219 inches is 1310 series, 3.625 is 1330, and 3.625 with 1.188 inch caps is 1350. Most Jeep transfer cases use 1310; full-size trucks often use 1350 or 1410.
What is a slip yoke eliminator and why would I need one?
A fixed yoke kit replaces the transfer case slip yoke with a short output shaft and a bolt-on yoke, moving the slip joint into a new driveshaft. It stops fluid loss when the shaft pulls out at full articulation, allows a longer driveshaft after a lift, and lets you fit a CV shaft to cure vibration. It is a common upgrade on lifted TJ and XJ Jeeps.
Can I swap a flange for a yoke on my transfer case?
Sometimes. Adapters such as the Rubicon Express flange adapter convert between flange and yoke styles on the JK so a different driveshaft can be used. The adapter must match both the transfer case output and the driveshaft's U-joint series, so check both ends before choosing.
Why does my new yoke leak at the transfer case?
The tailhousing seal was likely reused, damaged on installation, or the yoke's seal surface is grooved or rusty. Replace the seal with the correct one for a yoke with or without a slinger, polish the yoke surface, and lubricate the seal lip before sliding the yoke in.










