Shock boots keep grit and water off a lifted shock's shaft and seal. How to size, vent and inspect one, when it can trap…
Shock Absorbers
Showing 1057–1068 of 3453 resultsSorted by popularity
-
Shock Absorbers
Skyjacker Black MAX Shock Absorber – B8503
- Front Black MAX shock absorber, direct fit for listed 1999–2006 Chevrolet Silverado 1500 and GMC Sierra 1500 trucks
- Part number B8503; extended length 18.50 in., collapsed length 12.25 in.
- Black boot included with the unit
- Fitment also lists 2000–2005 Tahoe, Suburban, Yukon and Avalanche models
SKU: SKYB8503 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8067
- Rear Skyjacker Softride Nitro shock, part number N8067, for 4 to 5 in suspension lifts
- Fits 2007 to 2018 Jeep Wrangler JK, 2-door and 4-door models
- 150 PSI nitrogen gas, twin tube with oversized piston head
- Collapsed length 15.69 in, extended length 26.57 in, stroke 14.88 in
- Red polyurethane boot included, sold as each
SKU: SKYN8067 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8065
- Front Skyjacker Softride Nitro shock for the 2007-2018 Jeep Wrangler (JK)
- 150 PSI nitrogen gas pressure, twin tube design
- For 4-5 in. lift; collapsed 14.56 in., extended 24.79 in., stroke 14.23 in.
- Supplied individually; a second shock is needed for a pair
SKU: SKYN8065 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8063
- Rear Skyjacker Softride Nitro shock, part number N8063, for 6 to 8 in suspension lifts
- Fits 1984 to 2001 Jeep Cherokee XJ, 1997 to 2006 Wrangler TJ and 2004 to 2006 Wrangler LJ Unlimited models
- 150 PSI nitrogen gas pressurized twin tube design
- Red polyurethane boot included
- Shock will not lift the vehicle
SKU: SKYN8063 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8061
- Front Skyjacker Softride Nitro shock, part number N8061, for 7 to 9 in suspension lifts
- Fits 1970 to 1976 Ford F-100, 1977 to 1979 and 1997 to 2003 Ford F-150, 1978 to 1979 Ford Bronco and 1987 to 1995 Jeep Wrangler YJ
- Collapsed length 17.42 in, extended length 30.46 in, stroke 13.04 in
- 150 PSI nitrogen gas, twin tube, red boot included
- Sold individually
SKU: SKYN8061 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8060
- Rear Skyjacker Softride Nitro shock, part number N8060, with 150 PSI nitrogen gas
- Fits Ford, Chevrolet, GMC, Mazda and Toyota trucks and SUVs from 1965 to 2018, by model and year
- Bonded iron piston and chromed piston rod
- Red polyurethane bushings and red boot
- Carries a limited lifetime warranty
SKU: SKYN8060 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8059
- Front Skyjacker Softride Nitro shock, part number N8059, for 5 to 9 in suspension lifts
- Fits 1970 to 1979 Ford F-100, F-150, F-250 and F-350 and 1978 to 1979 Ford Bronco
- Also lists 1987 to 1995 Jeep Wrangler (YJ)
- Collapsed length 16.56 in, extended length 28.750 in
- Twin tube, 150 PSI nitrogen gas, red boot included
SKU: SKYN8059 -
Shock Absorbers
Skyjacker Softride Nitro Shock Absorber – N8058
- Skyjacker N8058 Softride Nitro rear shock absorber from the Nitro Series
- Gas charged with 150 PSI nitrogen, twin tube construction
- Designed for 3.5 – 5 in. suspension lifts and does not lift the vehicle
- Multi-stage velocity sensitive valving, oversized piston head, urethane bushings
- No vehicle fitment listed; labeled Direct Fit by the manufacturer
SKU: SKYN8058 -
Shock Absorbers
Skyjacker M95 Performance Monotube Shock Absorber – M9521
- Front Skyjacker M95 monotube shock, part number M9521, for 0 to 1.5 in of lift
- Fits classic 1967 to 1991 Chevrolet and GMC K-series and V-series trucks and Suburbans
- Also lists 1969 to 1974 and 1987 to 1991 Chevrolet Blazer and 1970 to 1991 GMC Jimmy
- Gas monotube body with 46mm bore
- Shock boot included, sold as each
SKU: SKYM9521 -
Shock Absorbers
Skyjacker M95 Performance Monotube Shock Absorber – M9518
- Rear Skyjacker M95 monotube shock, part number M9518, for 1 to 3 in of lift
- Fits 1984 to 2001 Jeep Cherokee XJ, 1997 to 2005 Wrangler TJ and 2004 to 2005 Wrangler LJ Unlimited models
- Gas monotube body with 46mm bore and internal bump stop
- 180 degree directional mounting
- Shock boot included, sold as each
SKU: SKYM9518 -
Shock Absorbers
Skyjacker M95 Performance Monotube Shock Absorber – M9517
- Front Skyjacker M95 monotube shock, part number M9517, for 0 to 2 in of lift
- Fits a broad run of Chevrolet, GMC, Dodge and Ram trucks and SUVs from 1961 through 2018
- Gas monotube body with 46mm bore and internal bump stop
- 180 degree directional mounting
- Shock boot included, sold as each
SKU: SKYM9517 -
Shock Absorbers
Skyjacker M95 Performance Monotube Shock Absorber – M9516
- Front Skyjacker M95 monotube shock, part number M9516, for 0 to 3 in of lift
- Fits 1984 to 2001 Jeep Cherokee XJ, 1986 to 1992 Comanche, 1993 to 1998 Grand Cherokee ZJ, 1999 to 2004 Grand Cherokee WJ, 1997 to 2005 Wrangler TJ and 2004 to 2005 Wrangler LJ
- Gas-charged monotube body with a high pressure nitrogen charge and floating piston
- 46mm bore, internal bump stop and 180 degree directional mounting
- Shock boot included, sold as each
SKU: SKYM9516
What a shock absorber does
A shock absorber is a damper. The spring holds the vehicle up, and the shock controls how fast that spring moves. Without working dampers a truck bounces repeatedly after every bump, tires lose contact with the ground, and braking and steering suffer. Off-road, shocks also absorb heat from constant motion, which is why fade becomes a concern on long, rough stretches.
Key specifications to compare
- Collapsed and extended length: These two numbers set the travel (extended minus collapsed). The shock must be long enough that it never limits suspension travel or bottoms out before the bump stops do, and short enough that it is not the first thing to run out at full droop.
- Mounts: Bar pin, stem, eyelet and bolt-in ends are not interchangeable without hardware. Match both the upper and lower mount styles to your vehicle.
- Body design: Monotube shocks usually run cooler and resist foaming better. Twin-tube shocks are common as stock replacements and are often quieter and lower in cost. Many listings state the body diameter, such as a 46mm smooth body.
- Reservoir: An external reservoir adds oil volume and gas capacity, which helps with heat in hard or sustained use.
- Shaft diameter: A larger shaft is generally more resistant to bending.
Choosing for your use
For a daily driver with a modest lift, a quality non-adjustable monotube or gas-charged twin-tube shock sized for your lift height is usually enough. If you tow, carry a heavy bumper and winch, or run fast desert roads, look at larger bodies, reservoirs and tunable valving. Pair the shock with the right spring rate; a shock cannot make up for a spring that is too soft or too stiff for the load.
Fitment and installation
Shocks are specific to lift height, axle and whether they are front or rear, so confirm fitment for your exact year, make and model and check the manufacturer's specifications. Replace shocks in axle sets, since one new and one worn shock gives uneven handling. Support the axle before removal so it cannot droop and stretch brake lines, and tighten fasteners to the specified torque. If you changed ride height, have the alignment checked afterward.
A final point on tuning: if a shock offers adjustable damping, change one setting at a time and note the result on a familiar road. Heavier loads, such as a winch bumper, roof tent or camping gear, often call for firmer valving than an empty truck. Inspect boots, bushings and mounting hardware at every oil change, since a worn bushing can mimic a failing shock.
Mistakes to avoid
The most common error is choosing shocks by brand or price without checking the length numbers. A shock that is too short lets the axle droop until the springs unseat or brake lines tighten, while one that is too long bottoms out and can bend the shaft or damage the mounts. Measure from mount to mount at ride height, then at full droop and full compression, and compare with the listed collapsed and extended lengths.
- Do not ignore worn bushings, since new shocks with tired bushings still clunk.
- Do not use a shock as a travel limiter; bump stops and limit straps do that job.
- Do not install shocks with the vehicle hanging from the frame and the springs unloaded, because mounts then sit in the wrong position.
Test drive on a familiar road after installation and listen for rattles before heading onto the trail.
Related guides
- Shock Boots: Why Every Lifted Shock Needs One
- Jeep JK Lift Heights: 2.5 vs 3.5 vs 4.5 Inch Compared
Jeep JK lift heights compared: the tires 2.5, 3.5 and 4.5-inch lifts clear, the track bars, arms, lines and driveshafts each needs, and which…
- Twin-Tube, Monotube or Reservoir: Picking the Right Shock
Twin-tube, monotube and reservoir shocks compared: how each handles heat, how to size one for your lift, and which design fits how you drive.
- Bilstein 5100 vs Fox 2.0 Performance: Which Shock for Your Lifted Truck or Jeep
Bilstein 5100 vs Fox 2.0 Performance: body, shaft, reservoir, travel and lift ratings across 417 part numbers, which trucks and Jeeps both fit, how…
Popular Shock Absorbers brands
- Pro Comp Suspension (898)
- Bilstein (615)
- Rancho (567)
- Fox Racing Shox (345)
- Skyjacker (279)
- Fabtech (232)
- ARB 4x4 Accessories (136)
- FOX (85)
- ICON Vehicle Dynamics (84)
- Rubicon Express (78)
- Icon Suspension (77)
- King Shocks (71)
Shock Absorbers FAQ
How do I know when shocks are worn out?
Common signs are oil leaking down the body, a bouncy or floaty ride, nose dive under braking, uneven tire wear and clunking from the mounts. A worn shock may also feel hot or weak when you compare it with a new one.
What is the difference between monotube and twin-tube shocks?
A monotube has a single working chamber with a floating piston separating oil and gas, which tends to shed heat well. A twin-tube uses an inner and outer tube and is common in factory-style replacements. Both can work well when matched to the vehicle.
Do I need new shocks after a lift?
Usually yes. A lift changes the distance between the mounts, so stock shocks may limit travel or bottom out. Choose shocks whose collapsed and extended lengths suit your lift height, and confirm the specifications with the manufacturer.
Should shocks be replaced in pairs?
Yes, replace both shocks on an axle together. Mixing new and worn dampers makes the two sides react differently, which affects handling and braking stability, especially on rough surfaces.














