Select your vehicle

Crush Sleeve

Dana Spicer

$12.99In stock
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 17, 2026 11:10 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Dana Spicer collapsible crush sleeve for the rear Super 44 axle
  • For 2007 and newer Jeep Wrangler JK models
  • 5/8 inch tall before crush

Description

Overview

The Dana Spicer crush sleeve is for 2007 and newer Jeep Wrangler JK models with a rear Super 44 axle, which falls in the 2007-2018 JK range. It is a collapsible sleeve, 5/8 inch tall before crush, that is used to set pinion preload on the rear Super 44.

Key features

  • Collapsible design
  • 5/8 inch tall before crush
  • Rear Super 44 axle application
  • Fits 2007 and newer Jeep Wrangler JK models.

Pinion setup and preload

A crush sleeve sits between the pinion bearings and sets how far the pinion nut can be drawn in. As the nut is tightened, the sleeve compresses until the bearings reach the preload the gear set needs. Too little preload lets the pinion move and wear the bearings, while too much can cause bearing heat and early failure. Because the sleeve deforms during that process, it is set once and then replaced rather than reused.

Pinion setup also involves the carrier bearings, pinion depth and gear mesh, so the sleeve is rarely the only part that changes. Many shops replace the pinion nut and check carrier bearing condition at the same time. Watch for a rough or grinding feel when turning the pinion by hand, a dry or noisy bearing, or play in the pinion flange, which can point to preload that has loosened over time.

  • Inspect the pinion bearings for pitting before reassembly
  • Use a new pinion nut when setting preload
  • Measure preload with an inch-pound torque wrench during setup

Specifications

Brand Dana Spicer
Axle type Super 44
Axle location Rear
Height before crush 5/8 inch
Design Collapsible
Vehicle named 2007 and newer Jeep Wrangler JK, per the short description

Vehicle fitment

This crush sleeve fits 2007 and newer Jeep Wrangler JK models with a rear Super 44 axle. The JK fitment range is 2007-2018.

Confirm your vehicle’s year, model and trim before ordering, especially for Wrangler JL, Gladiator, TJ or LJ models.

Installation notes

Collapsible sleeves are set once during a pinion setup, so a new one is needed each time pinion preload is set. Have a qualified shop measure and set preload on the rear Super 44.

What’s included

Only the crush sleeve is described.

Not included: the rear axle bearings and pinion hardware are not part of this sleeve.

SKU: D/S46925 Category:

Specification

Shipping weight 0.30 lbs
Package dimensions 4.00 × 4.00 × 4.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2018All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does this crush sleeve fit 2007 and newer Jeep Wrangler JK?

Yes, the short description names 2007 and newer JK Jeep models with a Super 44 rear end. The fitment range is 2007-2018, so confirm your year, model and trim before ordering.

Is this crush sleeve for a Super 44 front axle?

No. It is designed for the rear Super 44 axle only, so confirm the axle location on your vehicle and its year, model and trim before ordering.

How tall is this crush sleeve?

It is 5/8 inch tall before crush. The sleeve is collapsible, meaning it compresses when the pinion preload is set during installation, so the height changes as the setup is tightened.

How can I tell if pinion preload has loosened?

Look for play at the pinion flange, a rough or gritty feel when the pinion turns by hand, or noise that changes with speed. Any of these signs calls for a teardown and a fresh sleeve during the next pinion setup. Have the axle inspected by a qualified shop rather than relying on a single symptom.

Can a crush sleeve be reused after a gear swap?

No. Once a crush sleeve has been compressed, its set height has changed and it should be replaced. Reusing it can leave pinion preload outside the range the bearings need, so install a new sleeve whenever the pinion is removed and reset.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon