Select your vehicle
-13%

Dana Spicer Dana 44 Crush Sleeve – 43916

Dana Spicer

$14.18In stock
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 18, 2026 10:20 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Dana Spicer crush sleeve for Dana 44 rear axles (part number D/S43916)
  • Maintains proper pinion bearing preload
  • Direct replacement for late model factory crush sleeves
  • Aluminum sleeve for late model factory-style ring and pinions

Description

Overview

The Dana Spicer Dana 44 crush sleeve, part number D/S43916, is an aluminum rear axle sleeve that sets pinion bearing preload on late model factory-style ring and pinions. Dana Spicer offers it as a replacement for dealer crush sleeves that are often hard to find.

It is built for late model axles that use factory crush sleeves, so it suits Grand Cherokee and Commander applications.

Key features

  • Aluminum Dana 44 rear crush sleeve
  • Maintains proper pinion bearing preload
  • Designed for late model factory-style ring and pinions
  • Direct replacement for dealer crush sleeves

Pinion preload and reassembly

Pinion preload is the rotational resistance of the pinion bearings, and it is set by tightening the nut until the sleeve reaches the right point. Too little preload lets the pinion move under load and wears the gears. Too much preload overheats the bearings and can damage the seal. Setting preload is a measured job, not a guess.

Solid spacers and crush sleeves are not interchangeable, so match the type the axle was built with. Measure the bearing turning torque as the nut is tightened and compare it against the axle’s setup procedure. Keep pinion depth and carrier bearing preload in mind, because a change in one can affect the others.

  • Use a torque wrench on the pinion nut
  • Check bearing rotating torque at each step
  • Replace the pinion seal when the yoke is removed

Specifications

Brand Dana Spicer
Part number D/S43916
Axle type Dana 44
Position Rear
Material Aluminum
Ring and pinion Late model factory style

Vehicle fitment

It fits the 2006–2008 Jeep Commander (XK), the 1999–2004 Jeep Grand Cherokee (WJ), the 2005–2008 Jeep Grand Cherokee (WK) and the 1996–1998 Jeep Grand Cherokee (ZJ).

No Wrangler or Cherokee (XJ) models appear on the list, and the ZJ years are 1996 to 1998 only. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

A crush sleeve is compressed when the pinion nut is tightened to set bearing preload, so it is normally replaced whenever the pinion is set. Preload has to be set correctly, which is why a professional gear setup is usually recommended.

What’s included

The crush sleeve is the only part in the kit. Check the pinion nut and gear set against your installation before starting.

Fitment

VehicleYearsTrims
Jeep Commander (XK)2006–200865th Anniversary Edition, Base, Limited, Overland, Sport
Jeep Grand Cherokee (WJ)1999–2004Laredo, Limited, Overland, Special Edition, Sport
Jeep Grand Cherokee (WK)2005–200865th Anniversary Edition, Laredo, Limited, Overland, SRT8
Jeep Grand Cherokee (ZJ)1996–19985.9 Limited, Laredo, Limited, Orvis, TSi

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the Dana Spicer D/S43916 fit a Jeep Grand Cherokee ZJ?

It fits the 1996 to 1998 Jeep Grand Cherokee (ZJ). Confirm the year before ordering, since only those ZJ years apply.

What does a crush sleeve do?

It sets pinion bearing preload. The sleeve compresses when the pinion nut is tightened, which is why a crush sleeve is normally replaced rather than reused.

Is this sleeve made of aluminum?

Yes. The Dana 44 rear crush sleeve is aluminum, and it suits late model axles with factory crush sleeves and factory-style ring and pinions.

Can an old crush sleeve be reused?

No. A crush sleeve is deformed when the pinion nut is tightened, so it has already set its preload and should not be reused. Install a fresh sleeve each time the pinion is set.

Does the pinion nut need replacing too?

Often, yes. Pinion nuts are usually tightened once and replaced when the pinion is removed. Inspect the threads and the nut before reassembly, and check that the nut tightens without galling.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon