Dana 30 vs Dana 44 vs Dana 60: how to identify the axle under your Jeep or truck, what each one handles, and when…
Dana 44 Axle Parts, Axles, Gears, and Modifications
Showing 265–276 of 469 resultsSorted by popularity
-
Dana 44 Limited Slip Differentials and Parts
Auburn Gear Dana 44 30 Spline 3.92 Up Pro Series Limited Slip – 542082
Dana 44 Limited Slip Differentials and PartsAuburn Gear Dana 44 30 Spline 3.92 Up Pro Series Limited Slip – 542082
- Auburn Gear Pro Series Dana 44 limited slip, 30 spline, for 3.92 and up gears
- Higher preload rating than the standard H/P line
- Aggressive yet streetable limited slip action
- Four year replacement program (D-REX)
SKU: AUB542082 -
Dana 44 Limited Slip Differentials and Parts
Auburn Gear Dana 44 19 Spline 3.92 Up H/P Limited Slip – 5420111
Dana 44 Limited Slip Differentials and PartsAuburn Gear Dana 44 19 Spline 3.92 Up H/P Limited Slip – 5420111
- Auburn Gear Dana 44 limited slip differential, 19 spline, for 3.92 and up gears
- H/P Series with a preloaded cone clutch
- Hardened spider gears; part number 5420111
- Four year replacement program (D-REX)
SKU: AUB5420111 -
-
Dana 44 Lockers and Spools
ARB Dana 44 JK Rubicon 35 Spline 3.73 Down Air Locking Differential – RD157
Dana 44 Lockers and SpoolsARB Dana 44 JK Rubicon 35 Spline 3.73 Down Air Locking Differential – RD157
- Air locker for the rear Dana 44 on the Jeep JK with aftermarket 35-spline axles
- For 3.73 and down gears
- Air activated selectable locker with push button operation
- Needs a separate air compressor
SKU: ARBRD157 -
Dana 44 Lockers and Spools
ARB Nissan M226 32 Spline 10 Bolt Air Locking Differential – RD149
- Pneumatic selectable locker for a Nissan M226 rear axle with 32 splines
- Converts an open differential to a full spool
- 10-bolt design, part number RD149
- Needs an onboard air compressor, not included
SKU: ARBRD149 -
-
Dana 44 Lockers and Spools
ARB Dana 44 30 Spline 3.73 Ratio Down Air Locking Differential – RD117
- Air activated selectable locker for Dana 44 axles with 30 splines
- Built for gears at 3.73 ratio and numerically lower
- Push button operation converts an open differential to fully locked
- Needs a separate air compressor
SKU: ARBRD117 -
-
-
Dana 44 Lockers and Spools
ARB Dana 44 Super 35 Spline 3.92 Ratio Up Air Locking Differential – RD109
Dana 44 Lockers and SpoolsARB Dana 44 Super 35 Spline 3.92 Ratio Up Air Locking Differential – RD109
- ARB Air Locker for Dana 44 axles with 35 splines and a 3.92 ratio
- Pneumatic selectable locker that converts an open differential to a full spool
- Needs a separate ARB onboard air compressor
SKU: ARBRD109 -
Dana 44 Lockers and Spools
ARB Locker and Differential Air Locker Package for Dana 30/Dana 44 – DIFF4430
Dana 44 Lockers and SpoolsARB Locker and Differential Air Locker Package for Dana 30/Dana 44 – DIFF4430
- Air-operated selectable locker for Dana 30 and Dana 44 differentials, converting an open differential to a full spool.
- Needs an ARB onboard air compressor to activate the locker.
- The compressor kit runs a single locker or a dual front and rear system, with a 100 psi cut-off switch setting.
- Compressor draws 9 amps with no load and 20 amps at full load.
- Part number DIFF4430, UPC 700007718121, no vehicle fitment listed.
SKU: ARBDIFF4430 -
Dana 44 Miscellaneous Parts
ARB Differential Axle Breather – 170112
- Central breather manifold for up to four differentials, transmissions or transfer cases
- Includes 8m of 8mm tubing, four push-in fittings, filter and 25 cable ties
- Anodized aluminium manifold with an ARB compressor air filter
SKU: ARB170112
About the Dana 44
The Dana 44 is a popular medium-duty axle used in Jeeps, Ford trucks and Broncos, and other 4x4s, front or rear, and it is a common base for upgrades. Variants differ by spline count, housing, and mounting, so identify your axle carefully before ordering anything. The tag on the housing, the spline count, and the vehicle application are the starting points.
Parts here span routine maintenance items like seals and bearings through full gear and locker upgrades.
Gearing and differentials
Ring and pinion sets are chosen by ratio, such as 4.10, 4.56, or 5.13, usually to compensate for larger tires. Front and rear ratios must match, and sets should be installed with a master installation kit containing bearings, shims, and seals. Gear setup requires correct pinion depth and backlash measurements.
- Lockers and spools lock both wheels together for maximum traction.
- Limited slip units share torque between wheels while allowing some difference in speed.
- Open differential parts support rebuilds of the stock design.
Shafts, hubs, and wear parts
Axle shafts must match spline count and length, and some models need ABS tone rings or particular flange designs. Hubs, spindles, and ball joints wear with miles and trail use, and seals and bearings should be replaced together to protect the new components. U-joints and yokes need to match the shaft and driveline series.
Check the axle ratio, spline count, and brake configuration before purchasing any internal parts.
Installation guidance
Axle work is safety critical. Gear setup requires special tools and experience, and incorrect setup can cause noise and failure. Use jack stands, torque fasteners to specification, fill with the correct gear oil, and break in new gears gently. Professional installation is recommended for ring and pinion and locker work. Confirm fitment for your exact year, make, and model, and check the manufacturer's specifications.
Preparing for an axle project
Plan the project before tearing anything down. Identify the axle and its ratio, decide which parts to replace, and gather seals, bearings, gear oil, thread locker, and RTV or gaskets. Mark the driveshaft and carrier caps and keep parts organized.
Check axle housing straightness, tube condition, and mounting brackets. Many people upgrade axle shafts, lockers, and gears at the same time, because the housing is already open. Fill with the specified oil and drive gently for the first few hundred miles.
Spline count and axle shaft length are two of the first measurements to confirm. Dana 44 shafts come in different spline counts, and the inner and outer shafts on a front axle are different lengths on each side. Check the U-joint series, hub bolt pattern, and brake rotor mounting before choosing shafts.
Ring gear size, carrier break, and the pinion design also vary. Front and rear ring and pinion sets are not interchangeable, and a standard-rotation unit differs from a reverse-rotation unit found in some Jeep front axles. Carrier bearings and shims must be selected to suit the carrier you use.
Gear oil, additives, and limited slip friction modifiers all matter. Limited slip units often need a friction modifier, and lockers may need a particular type of oil. Check the oil level at each service, look for metal in the drain plug, and replace seals at the first sign of leaks to protect the brakes.
Related guides
- Dana 30 vs Dana 44 vs Dana 60: Which Axle Is Under Your Jeep or Truck, and When to Upgrade
- First SUV: The International Harvester Scout 80 Story
The first SUV wasn't a Jeep. See how the International Harvester Scout 80 came to be, how the Scout 800 and Scout II followed,…
- Is Your Dana 44 Vent Destroying Your Axle?
Learn how a Dana 44 axle vent works, which vent locations let water into the gear oil, and how to add a top-mounted breather…
Popular Dana 44 Axle Parts, Axles, Gears, and Modifications brands
- G2 Axle and Gear (178)
- Dana Spicer (93)
- Crown Automotive (58)
- Omix-Ada (35)
- Alloy USA (33)
- ARB 4x4 Accessories (13)
- TeraFlex (9)
- Auburn Gear (7)
- Detroit Locker (6)
- Rubicon Express (6)
- RCV Axles (4)
- Jeep (4)
Shop Dana 44 Axle Parts, Axles, Gears, and Modifications by type
- Dana 44 Axle Shafts (84)
- Dana 44 Ring and Pinion (68)
- Dana 44 Bearings and Install Kits (63)
- Dana 44 Oil Seals (56)
- Dana 44 Complete Assemblies (38)
- Dana 44 Differential Covers (31)
- Dana 44 Miscellaneous Parts (31)
- Dana 44 Hubs and Spindles (26)
- Dana 44 Lockers and Spools (26)
- Dana 44 Ball Joints (18)
- Dana 44 Drive Yokes and Flanges (13)
- Dana 44 U-Joints (9)
- Dana 44 Limited Slip Differentials and Parts (9)
- Dana 44 Open Differential Parts (7)
Dana 44 Axle Parts, Axles, Gears, and Modifications FAQ
How do I identify a Dana 44?
Look for a tag on the axle housing, a cover shape and bolt count, and the vehicle application. Spline count and ring gear diameter can be measured. Dana 44 variants differ, so verify before ordering parts.
What gear ratio should I choose?
Pick a ratio that restores performance with your tire size. Larger tires often call for numerically higher ratios, like 4.56 or 5.13, and front and rear ratios must match. Engine, transmission, and use all matter.
Do I need a master install kit?
It is strongly recommended with new gears. The kit includes bearings, seals, and shims needed to set pinion depth and backlash correctly. Reusing worn bearings can hurt gear life.
Can I install gears myself?
Only if you have the tools and experience. Setting pinion depth and backlash is precise work, and mistakes damage new gears. Many owners use a professional shop for ring and pinion installations.



