Towing
Showing 721–732 of 1114 resultsSorted by popularity
-
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75299
- DrawTite 75299 Class III/IV Max-Frame rear trailer hitch with a 2 in. receiver
- Ratings: 3500 lbs. GTW / 350 lbs. tongue weight; 4000 lb weight distributing / 400 lb tongue weight
- No drilling required; exhaust temperature lowered for install
- Does not fit with a roll pan
SKU: DRA75299 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75282
- DrawTite 75282 Class III/IV rear max-frame trailer hitch
- Fits 2005–2012 Nissan Frontier and 2009–2011 Suzuki Equator
- 5000 lb GTW and 8000 lb weight distributing rating
- 500 lb tongue weight, 800 lb with weight distribution
SKU: DRA75282 -
-
Receiver Hitches
DrawTite Round Tube Max-Frame Receiver – 75193
- DrawTite 75193 Class III/IV round tube Max-Frame receiver, rear mount, part number 75193
- Fits 2004–2006 Jeep Wrangler LJ and 1997–2006 Jeep Wrangler TJ
- Rated up to 4,000 lbs. GTW, all-welded construction with a 2 inch square tube opening
- Custom built per vehicle application, attaches at all frame attachment points, no drilling required
SKU: DRA75193 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75151
- Rear Class III/IV max-frame trailer hitch for 2003 to 2009 Dodge Ram pickups
- Rated 5000 lbs. GTW and 8000 lbs. weight distributing
- 500 lbs. tongue weight and 800 lb. weight distributing
- Fits models without a factory installed receiver
- Part number 75151
SKU: DRA75151 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75135
- Rear Class III/IV max-frame trailer hitch for 2002 to 2003 Dodge Ram 1500
- Rated 5000 lbs. GTW and 10000 lbs. weight distributing
- 500 lbs. tongue weight and 1000 lb. weight distributing
- Mounts as a direct fit with no adapters
- Part number 75135
SKU: DRA75135 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75078
- DrawTite 75078 Class III/IV Max-Frame trailer hitch, rear mount
- Fits the 1996–2004 Toyota Tacoma in Base, Limited, Pre Runner, S-Runner and SR5 trims
- 5000lbs. GTW and 500lbs. tongue weight, with 5500lb and 550lb weight distribution ratings
- 2 Inches X 2 Inches receiver, no drilling required
SKU: DRA75078 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75054
- Rear Class III/IV max-frame trailer hitch for 1984 to 2001 Jeep Cherokee XJ and 1984 to 1990 Jeep Wagoneer SJ
- Rated up to 3,500 lbs. GTW weight carrying and 5,500 lbs. GTW weight distributing
- 2 inch square receiver tube opening, black powder coat
- Custom built per vehicle application; drilling required
- Part number 75054
SKU: DRA75054 -
Receiver Hitches
DrawTite Front Mount Receiver – 65014
- Front mount frame mount receiver for 1992 to 1996 Ford F-250 and F-350 pickups
- 2 inch by 2 inch receiver opening
- 500 lbs. tongue weight, weight carrying
- 9000 lbs. maximum gross trailer weight, weight distribution
- Part number 65014; weight class not rated
SKU: DRA65014 -
Receiver Hitches
DrawTite Front Mount Receiver – 65005
- Front mount receiver for 1988 to 2000 Chevrolet and GMC C/K trucks, Suburbans, Blazers, Tahoes and Yukons
- DrawTite front mount receiver hitch, part number 65005
- 2 inch by 2 inch receiver, 500 lbs tongue weight, 9000 lbs maximum gross trailer weight
- All welded construction, built to fit the vehicle without adapters
- Does not fit with a roll pan
SKU: DRA65005 -
Receiver Hitches
DrawTite Class V Ultra Frame Hitch – 41933
- Class V Ultra Frame rear receiver hitch
- Rated 10000 lbs GTW and 1000 lbs tongue weight
- Weight distributing ratings of 12000 lbs GTW and 1200 lbs tongue
- Fits 2006–2008 Ford F-150, 2006–2008 Lincoln Mark LT and 2007–2012 Toyota Tundra
- No drill required, install time 20 min, part 41933
SKU: DRA41933 -
Receiver Hitches
DrawTite Class III/IV Round Tube Max-E-Loader Trailer Hitch – 41551
- Class III/IV rear round tube Max-E-Loader receiver hitch
- Rated 6000 lbs GTW and 600 lbs tongue weight
- Weight distributing ratings of 10000 lbs and 1000 lbs
- Fits the 2004–2011 Nissan Titan
- Part number 41551, UPC 742512415513, install time 15 min
SKU: DRA41551
What belongs in a towing setup
A complete tow setup has several links: a hitch mounted to the vehicle, a ball mount or head, a coupler-compatible ball, wiring, and, for heavier trailers, a brake controller and some form of suspension support. Weak or mismatched parts in any link limit the whole system, so it helps to think of the setup as a chain rather than a shopping list of separate items.
This category spans bolt-on receiver hitches, drop and adjustable ball mounts, gooseneck and fifth wheel mounting hardware, hitch pins and locks, trailer wiring connectors, mud flaps, and air or leaf-spring helpers that firm up the rear of a loaded truck.
Know your ratings first
Start with the numbers on your vehicle's door-jamb label and in the owner's manual: gross vehicle weight rating, gross combined weight rating, and the maximum tow rating. Every component, including the hitch class, ball mount, ball, pin, and trailer coupler, has its own rating, and your usable capacity is the lowest of them all.
Tongue weight matters as much as total weight. A trailer that is too light on the tongue can sway, while one that is too heavy overloads the rear axle and lifts weight off the front wheels. Many tow guides suggest roughly 10 to 15 percent of trailer weight on conventional trailers, but follow the manufacturer's numbers.
Matching hitch type to the job
- Receiver hitches come in classes, commonly I through V, with larger classes using 2-inch or 2.5-inch receiver openings and higher ratings.
- Gooseneck and fifth wheel hitches mount in the truck bed and suit heavy livestock, equipment, and RV trailers.
- Weight-distributing hitches and sway control spread tongue weight across the axles of the tow vehicle and trailer.
- Drop and rise ball mounts level the trailer so the coupler sits at the right height.
Measure from the ground to the top of the receiver and to the coupler of a level trailer before choosing a drop or rise.
Supporting the load and installing safely
Air springs, helper leaf springs, and similar load-leveling kits reduce rear sag when the truck is loaded. They do not raise the vehicle's rated capacity, so never treat them as a way to exceed the ratings on the label.
Many hitches bolt to existing frame holes, but some require drilling, trimming plastic, or removing exhaust parts. Use a torque wrench, follow the specified bolt torque, and recheck after the first few trips. Confirm fitment for your exact year, make, and model, and check the manufacturer's specifications before installing. Professional installation is sensible for gooseneck, fifth wheel, and brake controller wiring.
Common mistakes to avoid
Towing problems usually come from mismatched parts rather than a single bad component. Typical errors include using a ball that is rated below the trailer, ignoring tongue weight, skipping safety chains, and forgetting to confirm that the wiring connector matches the trailer plug.
Before every trip, walk around the rig: check the coupler latch and pin, chain crossing, light function, tire pressure on both vehicles, and brake controller gain. Lock the hitch pin when parked to deter theft.
Popular Towing brands
- Curt Manufacturing (269)
- AirLift (123)
- B&W Hitch (117)
- Firestone Ride-Rite (99)
- DrawTite (67)
- BOLT Lock (58)
- Weigh Safe Hitches (38)
- Smittybilt (37)
- Fastway Trailer Products (31)
- Supersprings (31)
- Husky Liners (26)
- Trimax Locks (22)
Shop Towing by type
- Suspension Load Leveling Kit (190)
- Hitches (200)
- Trailer Hitch Ball Mount (90)
- Brake Controllers & Electrical (118)
- Drop Hitches & Ball Mounts (86)
- Load Leveling Kits & Components (78)
- Trailer Hitch Pin Lock (47)
- Mud Flaps (43)
- Towing Accessories (49)
- Gooseneck Trailer Hitch (34)
- Leaf Spring Helper (26)
- Cargo Management (79)
- Gooseneck Trailer Hitch Mount Kit (16)
- Trailer Hitch Pin (14)
- Fifth Wheel Trailer Hitch Mount Kit (12)
- Truck Bed Cargo Organizer (9)
- Padlock (11)
- Trailer Wire Adapter (10)
- Trailer Hitch Covers (15)
- Fifth Wheel Trailer Hitch Bracket (7)
- Truck Tool Box Lock (8)
- Tow Bar Mounting Hardware (7)
- Fifth Wheel Trailer Hitch Slider (7)
- Trailer Wire Connector (5)
- Tie Down Anchors (6)
- Flasher (7)
- Trailer Brake Control (6)
- Tow Bar (5)
- Safety Chain (2)
- Leaf Spring Helper /Load Leveler Mounting Kits (4)
Towing FAQ
What hitch class do I need?
Match the class to the heavier of your trailer's loaded weight and tongue weight, using the lowest rating in the whole system. Class III and IV 2-inch receivers handle many campers and utility trailers, while heavy trailers may need Class V or a gooseneck. Confirm against your owner's manual.
Do I need a brake controller?
Many states require trailer brakes above a certain trailer weight, and the threshold varies by state. If your trailer has electric brakes, you need an in-cab controller wired to the vehicle. Check local regulations and the trailer manufacturer's guidance.
Can air springs increase my towing capacity?
No. Air springs and helper springs reduce sag and improve stability under load, but your towing and payload limits are set by the manufacturer. Staying within the ratings on the vehicle's label is still required for safe towing.
How do I choose a ball mount drop?
Park the loaded trailer level, then measure from the ground to the top of the receiver opening and to the underside of the coupler. The difference, adjusted for ball height, tells you the drop or rise needed to keep the trailer level.











