Shock boots keep grit and water off a lifted shock's shaft and seal. How to size, vent and inspect one, when it can trap…
Shock Absorbers
Showing 2725–2736 of 3453 resultsSorted by popularity
-
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-187601
- Bilstein 5160 Series reservoir shock absorber, part 25-187601, rear position
- Mono tube, gas charged design with a remote reservoir for extra shock oil capacity
- Collapsed length 16.54 in., extended length 28.09 in., travel length 11.55 in.
- Eye mounts at both ends (14.4mm), 14mm shaft diameter, zinc plated finish
- Lift height rating 0 to 2 in.; no specific vehicle named, Direct Fit
- Reservoir mounting kit included; boot not included
SKU: BIL25-187601 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-187595
- Bilstein 5160 Series front reservoir shock absorber, part number 25-187595
- Fits 2006–2008 Dodge Ram 1500 and 1994–2013 Ram 2500 and 3500 models
- Collapsed 15.2 in., extended 25.96 in., 10.76 in. travel
- Includes upper mount kit and reservoir frame mount kit
- UPC 651860653464
SKU: BIL25-187595 -
Shock Absorbers
Bilstein 5165 Series Reservoir Shock Absorber – 25-177503
- Monotube reservoir shock for custom lifted trucks and SUVs
- Remote reservoir adds oil capacity and heat dissipation
- Digressive valving and a floating dividing piston in the reservoir
- Reservoir mounting kit and detailed instructions included
SKU: BIL25-177503 -
-
Shock Absorbers
Bilstein 5165 Series Reservoir Shock Absorber – 25-176117
- Bilstein 5165 Series reservoir shock absorber, part number 25-176117
- Universal fit, gas charged monotube design
- Floating dividing piston and remote reservoir
- Triple-C finish with reservoir mounting kit included
SKU: BIL25-176117 -
Shock Absorbers
Bilstein 5165 Series Reservoir Shock Absorber – 25-176100
- Bilstein 5165 Series reservoir shock absorber, part number 25-176100
- Universal fit with gas charged monotube construction
- Remote reservoir for added shock oil capacity
- Includes reservoir mounting kit and instructions
SKU: BIL25-176100 -
-
Shock Absorbers
Bilstein 5100 Series Shock Absorber – 24-276061
- Fits 2001–2007 Toyota Sequoia Limited and SR5 per listed fitment
- Bilstein 5100 series rear shock, part number 24-276061
- Direct fit for 1 inch lifted 2WD and 4WD vehicles
- Monotube design with velocity sensitive digressive piston
- Collapsed length 15.06 in, extended length 23.96 in
SKU: BIL24-276061 -
Shock Absorbers
Bilstein 5100 Series Shock Absorber – 24-275002
- Direct fit rear shock for 2009-2018 Dodge Ram 1500 2WD trucks without air suspension
- Suits up to 1 inch of rear lift
- Collapsed length 16.44 in, extended length 26.04 in
- Bilstein B8 5100 monotube design with zinc plated finish
SKU: BIL24-275002 -
Shock Absorbers
Bilstein 5100 Series Shock Absorber – 24-274951
- Bilstein 5100 Series front shock absorber, part number 24-274951
- Fits 2017–2018 Ford F-250 and F-350 Super Duty, including King Ranch, Lariat, Platinum, XL and XLT trims
- 4WD models only, for a 2 to 2.5 inch lifted application
- Collapsed length 13.46 in., extended length 21.22 in.
SKU: BIL24-274951 -
Shock Absorbers
Bilstein 4600 Series Shock Absorber – 24-269439
- Bilstein 4600 Series rear shock absorber, part number 24-269439
- Fits 2014–2018 Ram 2500 trucks and 14-Current Ram 2500 2WD models
- Gas charged, smooth non-coilover body with 46 mm body diameter
- Yellow finish, without air leveling suspension
- UPC 651860796796
SKU: BIL24-269439 -
What a shock absorber does
A shock absorber is a damper. The spring holds the vehicle up, and the shock controls how fast that spring moves. Without working dampers a truck bounces repeatedly after every bump, tires lose contact with the ground, and braking and steering suffer. Off-road, shocks also absorb heat from constant motion, which is why fade becomes a concern on long, rough stretches.
Key specifications to compare
- Collapsed and extended length: These two numbers set the travel (extended minus collapsed). The shock must be long enough that it never limits suspension travel or bottoms out before the bump stops do, and short enough that it is not the first thing to run out at full droop.
- Mounts: Bar pin, stem, eyelet and bolt-in ends are not interchangeable without hardware. Match both the upper and lower mount styles to your vehicle.
- Body design: Monotube shocks usually run cooler and resist foaming better. Twin-tube shocks are common as stock replacements and are often quieter and lower in cost. Many listings state the body diameter, such as a 46mm smooth body.
- Reservoir: An external reservoir adds oil volume and gas capacity, which helps with heat in hard or sustained use.
- Shaft diameter: A larger shaft is generally more resistant to bending.
Choosing for your use
For a daily driver with a modest lift, a quality non-adjustable monotube or gas-charged twin-tube shock sized for your lift height is usually enough. If you tow, carry a heavy bumper and winch, or run fast desert roads, look at larger bodies, reservoirs and tunable valving. Pair the shock with the right spring rate; a shock cannot make up for a spring that is too soft or too stiff for the load.
Fitment and installation
Shocks are specific to lift height, axle and whether they are front or rear, so confirm fitment for your exact year, make and model and check the manufacturer's specifications. Replace shocks in axle sets, since one new and one worn shock gives uneven handling. Support the axle before removal so it cannot droop and stretch brake lines, and tighten fasteners to the specified torque. If you changed ride height, have the alignment checked afterward.
A final point on tuning: if a shock offers adjustable damping, change one setting at a time and note the result on a familiar road. Heavier loads, such as a winch bumper, roof tent or camping gear, often call for firmer valving than an empty truck. Inspect boots, bushings and mounting hardware at every oil change, since a worn bushing can mimic a failing shock.
Mistakes to avoid
The most common error is choosing shocks by brand or price without checking the length numbers. A shock that is too short lets the axle droop until the springs unseat or brake lines tighten, while one that is too long bottoms out and can bend the shaft or damage the mounts. Measure from mount to mount at ride height, then at full droop and full compression, and compare with the listed collapsed and extended lengths.
- Do not ignore worn bushings, since new shocks with tired bushings still clunk.
- Do not use a shock as a travel limiter; bump stops and limit straps do that job.
- Do not install shocks with the vehicle hanging from the frame and the springs unloaded, because mounts then sit in the wrong position.
Test drive on a familiar road after installation and listen for rattles before heading onto the trail.
Related guides
- Shock Boots: Why Every Lifted Shock Needs One
- Jeep JK Lift Heights: 2.5 vs 3.5 vs 4.5 Inch Compared
Jeep JK lift heights compared: the tires 2.5, 3.5 and 4.5-inch lifts clear, the track bars, arms, lines and driveshafts each needs, and which…
- Twin-Tube, Monotube or Reservoir: Picking the Right Shock
Twin-tube, monotube and reservoir shocks compared: how each handles heat, how to size one for your lift, and which design fits how you drive.
- Bilstein 5100 vs Fox 2.0 Performance: Which Shock for Your Lifted Truck or Jeep
Bilstein 5100 vs Fox 2.0 Performance: body, shaft, reservoir, travel and lift ratings across 417 part numbers, which trucks and Jeeps both fit, how…
Popular Shock Absorbers brands
- Pro Comp Suspension (898)
- Bilstein (615)
- Rancho (567)
- Fox Racing Shox (345)
- Skyjacker (279)
- Fabtech (232)
- ARB 4x4 Accessories (136)
- FOX (85)
- ICON Vehicle Dynamics (84)
- Rubicon Express (78)
- Icon Suspension (77)
- King Shocks (71)
Shock Absorbers FAQ
How do I know when shocks are worn out?
Common signs are oil leaking down the body, a bouncy or floaty ride, nose dive under braking, uneven tire wear and clunking from the mounts. A worn shock may also feel hot or weak when you compare it with a new one.
What is the difference between monotube and twin-tube shocks?
A monotube has a single working chamber with a floating piston separating oil and gas, which tends to shed heat well. A twin-tube uses an inner and outer tube and is common in factory-style replacements. Both can work well when matched to the vehicle.
Do I need new shocks after a lift?
Usually yes. A lift changes the distance between the mounts, so stock shocks may limit travel or bottom out. Choose shocks whose collapsed and extended lengths suit your lift height, and confirm the specifications with the manufacturer.
Should shocks be replaced in pairs?
Yes, replace both shocks on an axle together. Mixing new and worn dampers makes the two sides react differently, which affects handling and braking stability, especially on rough surfaces.














