Shock boots keep grit and water off a lifted shock's shaft and seal. How to size, vent and inspect one, when it can trap…
Shock Absorbers
Showing 2689–2700 of 3453 resultsSorted by popularity
-
Shock Absorbers
B8 5160 Series Remote Reservoir Shock Absorber
- Bilstein 25-243734 B8 5160 remote reservoir shock absorber for the rear.
- Fits 2000–2006 Toyota Tundra in Base, Limited and SR5 trims.
- Collapsed length 13.84 in, extended length 23.23 in, travel 9.39 in.
- Remote reservoir, mono tube, 360 degree swivel banjo hose fitting.
- Boot not included.
SKU: BIL25-243734 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-242539
- Bilstein 25-242539 5160 Series reservoir shock absorber for the rear right position, 0 to 1.5 in. lift.
- Fits 2005–2018 Toyota Tacoma in several trims.
- Collapsed length 14.22 in, extended length 24.06 in, travel 9.84 in.
- Remote reservoir, mono tube, 14mm shaft, zinc plated finish.
- Includes upper mount kit and reservoir mount kit; boot not included.
SKU: BIL25-242539 -
Shock Absorbers
Bilstein 5160 Series Shock Absorber – 25-218190
- Bilstein 5160 Series front remote reservoir shock, part number 25-218190
- Gas charged monotube with a 46mm smooth body (non-coilover)
- Collapsed length 15.57 in (395.5 mm), extended length 24.23 in (615.5 mm)
- Direct-fit design for a 4 – 6 in. lift; confirm fit for your vehicle before ordering.
- Zinc plated finish
SKU: BIL25-218190 -
Shock Absorbers
Bilstein 5160 Series Shock Absorber – 25-197761
- Bilstein 25-197761 5160 Series rear remote reservoir shock
- 46mm monotube body; collapsed 18.70 in. to extended 31.81 in.
- Direct fit for a 3 to 4 in. lift; no vehicle named
- Zinc plated finish with a remote reservoir on the rear unit
SKU: BIL25-197761 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-194012
- Bilstein 5160 Series front reservoir shock absorber, part number 25-194012
- Gas charged mono tube design with a remote reservoir
- Fits a 3.5 – 4.5 in. lift; collapsed length 15.37 in., extended length 26.39 in.
- Includes upper mount and reservoir mounting kit; boot not included
SKU: BIL25-194012 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-193145
- Bilstein 5160 Series rear remote reservoir shock, part number 25-193145
- 46mm digressive piston with self-adjusting deflective disc valving
- Zinc plated finish; designed for vehicles with a 3 inch lift
- Collapsed length 13.44 in (341.3mm), extended 22.00 in (558.8mm)
SKU: BIL25-193145 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-193138
- Bilstein 25-193138 5160 Series front stock-mount remote reservoir shock
- 46mm digressive piston and self-adjusting deflective disc valving
- Collapsed 13.11 in. to extended 21.87 in. length, zinc plated
- Direct fit; confirm your vehicle before ordering
SKU: BIL25-193138 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-193121
- Rear remote reservoir shock for 2004–2006 Jeep Wrangler LJ and 1999–2006 Wrangler TJ
- Collapsed length 14.95 inch (379.7mm), extended length 25.00 inch (635mm)
- Designed for a 3.5 – 4.5 in. lift
- Zinc plated, gas charged
- Part number 25-193121, UPC 651860666167
SKU: BIL25-193121 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-193114
- Front reservoir shock, Bilstein part number 25-193114, UPC 651860666068
- Collapsed length 14.59 in., extended length 24.70 in., travel 11.02 in.
- Lift range 3 – 4.5 in.
- Upper mount and reservoir mount included
- Confirm fit for your vehicle before ordering.
SKU: BIL25-193114 -
Shock Absorbers
Bilstein 5160 Series Shock Absorber – 25-188394
- Rear shock for 1999–2004 Ford F-250 and F-350 Super Duty, per the listed fitment
- Collapsed length 18.03 in. (458 mm), extended length 31.24 in. (793.5 mm)
- Gas charged monotube with a 46mm smooth body
- Lift range 0 – 2 in.
- Part number 25-188394, UPC 651860662329
SKU: BIL25-188394 -
Shock Absorbers
Bilstein 5160 Series Shock Absorber – 25-188387
- Front 5160 Series shock for 1999–2004 Ford F-250 and F-350 Super Duty, per the listed fitment
- Collapsed length 14.33 in. (364 mm), extended length 23.72 in. (602.5 mm)
- Gas pressure monotube with a 46mm smooth body
- Lift range 0 – 3.5 in.
- Specifications list a reservoir; part number 25-188387
SKU: BIL25-188387 -
Shock Absorbers
Bilstein 5160 Series Reservoir Shock Absorber – 25-188370
- Rear reservoir shock for 1999–2004 Ford F-250 and F-350 Super Duty, per the listed fitment
- Collapsed length 20.28 in. (515 mm), extended length 34.39 in. (873.5 mm)
- Gas charged 46mm monotube body with remote reservoir
- Designed for a 3 in. lift
- Zinc plated finish, Bilstein part number 25-188370
SKU: BIL25-188370
What a shock absorber does
A shock absorber is a damper. The spring holds the vehicle up, and the shock controls how fast that spring moves. Without working dampers a truck bounces repeatedly after every bump, tires lose contact with the ground, and braking and steering suffer. Off-road, shocks also absorb heat from constant motion, which is why fade becomes a concern on long, rough stretches.
Key specifications to compare
- Collapsed and extended length: These two numbers set the travel (extended minus collapsed). The shock must be long enough that it never limits suspension travel or bottoms out before the bump stops do, and short enough that it is not the first thing to run out at full droop.
- Mounts: Bar pin, stem, eyelet and bolt-in ends are not interchangeable without hardware. Match both the upper and lower mount styles to your vehicle.
- Body design: Monotube shocks usually run cooler and resist foaming better. Twin-tube shocks are common as stock replacements and are often quieter and lower in cost. Many listings state the body diameter, such as a 46mm smooth body.
- Reservoir: An external reservoir adds oil volume and gas capacity, which helps with heat in hard or sustained use.
- Shaft diameter: A larger shaft is generally more resistant to bending.
Choosing for your use
For a daily driver with a modest lift, a quality non-adjustable monotube or gas-charged twin-tube shock sized for your lift height is usually enough. If you tow, carry a heavy bumper and winch, or run fast desert roads, look at larger bodies, reservoirs and tunable valving. Pair the shock with the right spring rate; a shock cannot make up for a spring that is too soft or too stiff for the load.
Fitment and installation
Shocks are specific to lift height, axle and whether they are front or rear, so confirm fitment for your exact year, make and model and check the manufacturer's specifications. Replace shocks in axle sets, since one new and one worn shock gives uneven handling. Support the axle before removal so it cannot droop and stretch brake lines, and tighten fasteners to the specified torque. If you changed ride height, have the alignment checked afterward.
A final point on tuning: if a shock offers adjustable damping, change one setting at a time and note the result on a familiar road. Heavier loads, such as a winch bumper, roof tent or camping gear, often call for firmer valving than an empty truck. Inspect boots, bushings and mounting hardware at every oil change, since a worn bushing can mimic a failing shock.
Mistakes to avoid
The most common error is choosing shocks by brand or price without checking the length numbers. A shock that is too short lets the axle droop until the springs unseat or brake lines tighten, while one that is too long bottoms out and can bend the shaft or damage the mounts. Measure from mount to mount at ride height, then at full droop and full compression, and compare with the listed collapsed and extended lengths.
- Do not ignore worn bushings, since new shocks with tired bushings still clunk.
- Do not use a shock as a travel limiter; bump stops and limit straps do that job.
- Do not install shocks with the vehicle hanging from the frame and the springs unloaded, because mounts then sit in the wrong position.
Test drive on a familiar road after installation and listen for rattles before heading onto the trail.
Related guides
- Shock Boots: Why Every Lifted Shock Needs One
- Jeep JK Lift Heights: 2.5 vs 3.5 vs 4.5 Inch Compared
Jeep JK lift heights compared: the tires 2.5, 3.5 and 4.5-inch lifts clear, the track bars, arms, lines and driveshafts each needs, and which…
- Twin-Tube, Monotube or Reservoir: Picking the Right Shock
Twin-tube, monotube and reservoir shocks compared: how each handles heat, how to size one for your lift, and which design fits how you drive.
- Bilstein 5100 vs Fox 2.0 Performance: Which Shock for Your Lifted Truck or Jeep
Bilstein 5100 vs Fox 2.0 Performance: body, shaft, reservoir, travel and lift ratings across 417 part numbers, which trucks and Jeeps both fit, how…
Popular Shock Absorbers brands
- Pro Comp Suspension (898)
- Bilstein (615)
- Rancho (567)
- Fox Racing Shox (345)
- Skyjacker (279)
- Fabtech (232)
- ARB 4x4 Accessories (136)
- FOX (85)
- ICON Vehicle Dynamics (84)
- Rubicon Express (78)
- Icon Suspension (77)
- King Shocks (71)
Shock Absorbers FAQ
How do I know when shocks are worn out?
Common signs are oil leaking down the body, a bouncy or floaty ride, nose dive under braking, uneven tire wear and clunking from the mounts. A worn shock may also feel hot or weak when you compare it with a new one.
What is the difference between monotube and twin-tube shocks?
A monotube has a single working chamber with a floating piston separating oil and gas, which tends to shed heat well. A twin-tube uses an inner and outer tube and is common in factory-style replacements. Both can work well when matched to the vehicle.
Do I need new shocks after a lift?
Usually yes. A lift changes the distance between the mounts, so stock shocks may limit travel or bottom out. Choose shocks whose collapsed and extended lengths suit your lift height, and confirm the specifications with the manufacturer.
Should shocks be replaced in pairs?
Yes, replace both shocks on an axle together. Mixing new and worn dampers makes the two sides react differently, which affects handling and braking stability, especially on rough surfaces.















