Gussets & Tabs
Showing 37–48 of 59 resultsSorted by popularity
-
-
-
Gussets & Tabs
Artec Inner Frame Bracket – BR1017
- Artec Industries BR1017 inner frame bracket for control arm mounting
- 2.625 inch mounting width with 9/16 inch bolt hole for Cartridge Joints
- Top grease fitting access and skid plate guard the joint
- Made from 1/4 inch thick boxed steel plate
- Universal fit, no specific vehicle named
SKU: A/IBR1017 -
Gussets & Tabs
Artec Lower Link Frame Bracket – BR1009
- Artec Industries BR1009 lower link frame bracket, a control arm mount
- 2.625 inch mounting width and 9/16 inch bolt hole for Cartridge Joints
- Grease fitting can sit on top, with the joint mounted grease fitting up
- Made from 1/4 inch thick boxed steel plate
- Universal fit, not built for one make or model
SKU: A/IBR1009 -
Gussets & Tabs
Artec Adjustable Link Tower – BR1008L
- Artec BR1008L adjustable link tower, a control arm mount for 3-link and 4-link suspensions
- Mounting holes at 7, 8 and 9 inches from the axle centerline for fine suspension tuning
- Fits joints with a 2.625-inch mounting width, including 1.25-inch rod ends with misalignment spacers
- 9/16-inch bolt hole that can be drilled out for larger sizes
- Made from .250-inch thick steel in four unwelded pieces that jig together
- Tube diameter is 3-1/4 inches.
SKU: A/IBR1008L -
-
-
Gussets & Tabs
Artec Inner Frame Bracket – BR1018
- Universal inner frame bracket for the front driver or rear passenger position
- 1/4 inch thick boxed steel with a 25 degree angle
- 2.625 inch mounting width and 9/16 inch bolt hole
- Tapered sides and top grease fitting access
- Single bracket with a skid plate for the joint, bare steel
SKU: A/IBR1018 -
Gussets & Tabs
Artec Heavy Duty Raised Tracbar Bracket – JK4406
- Raised front tracbar bracket for Dana 30 or Dana 44 JK axles
- Raised tracbar holes at 1.75 inch and 3.0 inch
- Built for a drag link flip kit
- Lifts the factory sway bar mount 1.75 inch
- Made from 1/4 inch mild steel, bare steel finish
- Adjusts roll center 3 inches higher for stability
SKU: A/IJK4406 -
-
Gussets & Tabs
Artec Lower Link Axle Brackets – BR1011
- Universal lower link axle brackets, supplied as a pair
- 1/4 inch thick mild steel with a 10 degree angle
- 2.65 inch joint mounting width, 9/16 inch bolt hole in the detailed copy
- Bottom skid plate and top grease fitting access
- Rod end not included, bare steel finish
SKU: A/IBR1011
What gussets and tabs are used for
A gusset is a triangular or cross-shaped plate welded at a joint to spread load and stiffen it. A tab is a small plate, often with a drilled hole, that gives a link, shock or strap something to bolt to. Together they are everyday parts in axle truss work, link mounts and custom frame builds.
The listings include round and square iron cross gussets, a nuke gusset, flat tabs, tube tabs and a Jeep JK rear trac bar bracket.
Shapes and when to use them
- Flat tabs weld to a flat surface such as a frame rail or bracket plate.
- Tube tabs are contoured to wrap a round tube, such as an axle tube or cage member.
- Iron cross and similar gussets reinforce the area where an axle tube meets the housing or a bracket meets a tube.
- Trick tabs and drilled-hole tabs hold bolts of a stated diameter for links, shocks or accessories.
Specs to compare
Material grade and thickness are the first checks. Common choices are mild steel plate, with thicker plate used for suspension link mounts. Compare hole diameter against the bolt or bushing you plan to use, and look at the stated plate thickness and contour to be sure it suits the tube diameter or surface.
Pieces made by laser or CNC cutting tend to fit cleanly, but you still need to prep the mating surface by removing paint, rust and mill scale for a sound weld.
Fabrication and safety notes
Gussets and tabs on suspension and axle parts carry significant loads, and a poor weld can fail without warning. Use the right welding process for the material, fit the piece tightly and keep the welding heat controlled to avoid distorting thin-wall tubing. Correct link geometry is critical, so plan mount positions before welding.
If you are not an experienced welder, have a qualified fabricator do the work. After welding, paint or coat bare steel to resist rust, and inspect the welds regularly for cracks.
Further checks and care
Buying checklist
Measure the tube diameter or surface where the piece will go, then compare it to the contour listed on the product page. Count how many pieces you need, since link mounts usually come in pairs. Gather a bolt, bushing or heim joint to test the hole size, and confirm that the plate thickness suits your welding equipment. Planning the layout on paper first saves cut-off mistakes.
Welding and prep guidance
Clean steel to bare metal where you will weld, and remove oil and coatings that burn and contaminate the weld. Tack the piece in position, check alignment against a square or a measured reference, and then complete the weld in short passes to limit heat. Full-penetration welding on thicker plate needs a proper joint prep and sufficient amperage. Let welds cool slowly on high-stress parts, and avoid quenching, which can make the area brittle.
Common mistakes and good practice
A frequent error is placing tabs before confirming suspension geometry, which causes bump steer or binding. Another is welding across axle tubes without considering the heat's effect on tube straightness. Use gussets to spread loads over a larger area instead of relying on a short weld. Paint or coat the finished work, and inspect tabs and bolts after trail use. Use hardware of adequate grade, and replace any bolt that has been bent or stretched.
Popular Gussets & Tabs brands
- Artec Industries (42)
- Blue Torch Fabworks (13)
- Trail Gear (6)
- TeraFlex (3)
- Poison Spyder Customs (2)
- Mountain Off Road Enterprises (2)
- Rock Hard 4x4 Parts (1)
- JcrOffroad (1)
- Rubicon Express (1)
- G2 Axle and Gear (1)
Gussets & Tabs FAQ
What is the difference between a gusset and a tab?
A gusset is a reinforcing plate placed at a joint to add stiffness and spread stress. A tab is a mounting point, typically with a hole, for attaching a link, shock or other part.
Can I bolt on gussets instead of welding?
Not in general. Gussets work because they are welded to both surfaces, which creates a continuous load path. Bolted or adhesive attachment does not provide the same reinforcement.
What thickness should I use for a link mount tab?
It depends on the bolt size, the load and the material. Follow the part or kit maker's specification, and ask an experienced fabricator when you design your own mounts, as undersized tabs can tear or bend.











