Dana 30 vs Dana 44 vs Dana 60: how to identify the axle under your Jeep or truck, what each one handles, and when…
Dana 44 Axle Parts, Axles, Gears, and Modifications
Showing 157–168 of 469 resultsSorted by popularity
-
Dana 44 Lockers and Spools
Detroit Locker Dana 44 3.92 Up Front TrueTrac – 913A592
- Detroit Locker 913A592 TrueTrac limited-slip for a Dana 44 front axle
- Dana 44 front axle, 30 splines, 3.92 up ratio
- All gear driven, clutchless design
- Automatic power transfer between wheels
- UPC 91305920000
SKU: EAT913A592 -
-
-
Dana 44 Lockers and Spools
Detroit Locker Nissan Titan Dana 44 TrueTrac – 913A582
- Detroit Locker 913A582 TrueTrac limited-slip differential
- Clutchless, all gear driven design with no clutches to wear out
- Rear Nissan M226 D44 axle, 32 splines
- Nissan Titan application, with model years to be confirmed before ordering
- UPC 70000341652
SKU: EAT913A582 -
Dana 44 Lockers and Spools
Eaton Dana 44 30 Spline 3.73 Down 4 Pinion E-Locker – 19977-010
- Eaton E-Locker part 19977-010, an electronic push-button selectable locker
- Built for Dana 44 axles with 30 splines, rear or front location
- Switches from open to spool with a button press, no air lines or cables
- Runs on 12 volt power
- No vehicle years or models are listed
SKU: EAT19977-010 -
-
-
Dana 44 Complete Assemblies
Dana Spicer Jeep JK Ultimate Dana 44 Front Axle Assembly 5.38 Ratio – 10010742
Dana 44 Complete AssembliesDana Spicer Jeep JK Ultimate Dana 44 Front Axle Assembly 5.38 Ratio – 10010742
- Fits 2007–2017 Jeep Wrangler (JK) models
- Ultimate Dana 44 front axle assembly with a 5.38 gear ratio
- Factory electric locker (selectable electronic locking differential)
- Spicer chromoly axle shafts and SPL 1350 u-joints
- Direct bolt-in; reuses the stock wheel ends and brakes
SKU: D/S10010742 -
Dana 44 Complete Assemblies
Dana Spicer Jeep JK Ultimate Dana 44 Front Axle Assembly 3.73 Ratio – 10010519
Dana 44 Complete AssembliesDana Spicer Jeep JK Ultimate Dana 44 Front Axle Assembly 3.73 Ratio – 10010519
- Ultimate Dana 44 front axle with 3.73 ratio and factory electric locker
- Factory electric locker, selectable electronic locking differential
- 5/16 inch thick axle tubes and Spicer chromoly axle shafts
- Dana Spicer part number 10010519, UPC 23913483692
SKU: D/S10010519 -
Dana 44 Differential Covers
Dynatrac Dana 44 Pro Series Iron Cover – DA44-1X4033-BB
- Dynatrac Dana 44 Pro Series iron differential cover, part number DA44-1X4033-BB
- Cast from proprietary nodular iron, powder coated
- Dana 44 and Dana 44 JK axle types, front or rear
- Universal Fit label; no vehicle years stated
SKU: DPCDA44-1X4033-BB -
About the Dana 44
The Dana 44 is a popular medium-duty axle used in Jeeps, Ford trucks and Broncos, and other 4x4s, front or rear, and it is a common base for upgrades. Variants differ by spline count, housing, and mounting, so identify your axle carefully before ordering anything. The tag on the housing, the spline count, and the vehicle application are the starting points.
Parts here span routine maintenance items like seals and bearings through full gear and locker upgrades.
Gearing and differentials
Ring and pinion sets are chosen by ratio, such as 4.10, 4.56, or 5.13, usually to compensate for larger tires. Front and rear ratios must match, and sets should be installed with a master installation kit containing bearings, shims, and seals. Gear setup requires correct pinion depth and backlash measurements.
- Lockers and spools lock both wheels together for maximum traction.
- Limited slip units share torque between wheels while allowing some difference in speed.
- Open differential parts support rebuilds of the stock design.
Shafts, hubs, and wear parts
Axle shafts must match spline count and length, and some models need ABS tone rings or particular flange designs. Hubs, spindles, and ball joints wear with miles and trail use, and seals and bearings should be replaced together to protect the new components. U-joints and yokes need to match the shaft and driveline series.
Check the axle ratio, spline count, and brake configuration before purchasing any internal parts.
Installation guidance
Axle work is safety critical. Gear setup requires special tools and experience, and incorrect setup can cause noise and failure. Use jack stands, torque fasteners to specification, fill with the correct gear oil, and break in new gears gently. Professional installation is recommended for ring and pinion and locker work. Confirm fitment for your exact year, make, and model, and check the manufacturer's specifications.
Preparing for an axle project
Plan the project before tearing anything down. Identify the axle and its ratio, decide which parts to replace, and gather seals, bearings, gear oil, thread locker, and RTV or gaskets. Mark the driveshaft and carrier caps and keep parts organized.
Check axle housing straightness, tube condition, and mounting brackets. Many people upgrade axle shafts, lockers, and gears at the same time, because the housing is already open. Fill with the specified oil and drive gently for the first few hundred miles.
Spline count and axle shaft length are two of the first measurements to confirm. Dana 44 shafts come in different spline counts, and the inner and outer shafts on a front axle are different lengths on each side. Check the U-joint series, hub bolt pattern, and brake rotor mounting before choosing shafts.
Ring gear size, carrier break, and the pinion design also vary. Front and rear ring and pinion sets are not interchangeable, and a standard-rotation unit differs from a reverse-rotation unit found in some Jeep front axles. Carrier bearings and shims must be selected to suit the carrier you use.
Gear oil, additives, and limited slip friction modifiers all matter. Limited slip units often need a friction modifier, and lockers may need a particular type of oil. Check the oil level at each service, look for metal in the drain plug, and replace seals at the first sign of leaks to protect the brakes.
Related guides
- Dana 30 vs Dana 44 vs Dana 60: Which Axle Is Under Your Jeep or Truck, and When to Upgrade
- First SUV: The International Harvester Scout 80 Story
The first SUV wasn't a Jeep. See how the International Harvester Scout 80 came to be, how the Scout 800 and Scout II followed,…
- Is Your Dana 44 Vent Destroying Your Axle?
Learn how a Dana 44 axle vent works, which vent locations let water into the gear oil, and how to add a top-mounted breather…
Popular Dana 44 Axle Parts, Axles, Gears, and Modifications brands
- G2 Axle and Gear (178)
- Dana Spicer (93)
- Crown Automotive (58)
- Omix-Ada (35)
- Alloy USA (33)
- ARB 4x4 Accessories (13)
- TeraFlex (9)
- Auburn Gear (7)
- Detroit Locker (6)
- Rubicon Express (6)
- Warn (4)
- RCV Axles (4)
Shop Dana 44 Axle Parts, Axles, Gears, and Modifications by type
- Dana 44 Axle Shafts (84)
- Dana 44 Ring and Pinion (68)
- Dana 44 Bearings and Install Kits (63)
- Dana 44 Oil Seals (56)
- Dana 44 Complete Assemblies (38)
- Dana 44 Differential Covers (31)
- Dana 44 Miscellaneous Parts (31)
- Dana 44 Hubs and Spindles (26)
- Dana 44 Lockers and Spools (26)
- Dana 44 Ball Joints (18)
- Dana 44 Drive Yokes and Flanges (13)
- Dana 44 U-Joints (9)
- Dana 44 Limited Slip Differentials and Parts (9)
- Dana 44 Open Differential Parts (7)
Dana 44 Axle Parts, Axles, Gears, and Modifications FAQ
How do I identify a Dana 44?
Look for a tag on the axle housing, a cover shape and bolt count, and the vehicle application. Spline count and ring gear diameter can be measured. Dana 44 variants differ, so verify before ordering parts.
What gear ratio should I choose?
Pick a ratio that restores performance with your tire size. Larger tires often call for numerically higher ratios, like 4.56 or 5.13, and front and rear ratios must match. Engine, transmission, and use all matter.
Do I need a master install kit?
It is strongly recommended with new gears. The kit includes bearings, seals, and shims needed to set pinion depth and backlash correctly. Reusing worn bearings can hurt gear life.
Can I install gears myself?
Only if you have the tools and experience. Setting pinion depth and backlash is precise work, and mistakes damage new gears. Many owners use a professional shop for ring and pinion installations.









