Select your vehicle

Mountain Off Road Enterprises Rear Cross member Reinforcing Plate – RFP7686

Mountain Off Road Enterprises

Shop Jeep CJ7 Frame Stiffener on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 3/16 inch laser cut rear crossmember reinforcing plate
  • Fits 1976-1986 Jeep CJ5 and CJ7 and 1981-1985 Scrambler
  • Bare steel, welding required
  • Repairs or reinforces the rear frame
  • Part number RFP7686 from Mountain Off Road Enterprises

Description

Overview

The Mountain Off Road Enterprises Rear Crossmember Reinforcing Plate, part RFP7686, is a 3/16 inch laser cut steel plate for the rear frame crossmember of the 1976-1983 Jeep CJ5, the 1976-1986 Jeep CJ7 and the 1981-1985 Jeep Scrambler.

The plate adds strength to the rear of the frame. It can repair a broken crossmember or be fitted to a sound frame to help keep it from breaking.

It is intended for rear frames that carry bumpers with tire carriers for large tires, since those loads put stress on the rear frame.

Key features

  • 3/16 inch laser cut steel
  • Line up the holes and weld the plate in place
  • Can repair a broken crossmember
  • Can be fitted to a good frame as reinforcement
  • Intended for rear frames that carry bumpers with tire carriers for large tires
  • Bare steel finish

Frame reinforcement basics

Frame reinforcement plates spread load across the rear crossmember so the stress from a heavy rear bumper is not concentrated at one weak point. Plates like this are usually added when a rear bumper carries a heavy tire carrier, since the leverage on the frame increases with the weight at the back.

Good preparation matters more than the plate itself. Grind the frame to clean metal, fit the plate dry before tacking it, and weld both edges to avoid a new crack line. After welding, check the frame for cracks around the weld and recheck the bumper bolts after a few trail runs.

  • Check the frame for cracks before welding
  • Fit the plate dry and mark the holes first
  • Weld in short passes to limit heat distortion
  • Recheck bumper and carrier bolts after trail use

Specifications

Brand Mountain Off Road Enterprises
Part number RFP7686
Position Rear crossmember
Thickness 3/16 inch
Material Steel, bare finish
Installation Welded in place

Vehicle fitment

It fits the 1976-1983 Jeep CJ5 in Base, Golden Eagle, Laredo, Limited and Renegade trims, the 1976-1986 Jeep CJ7 in Base, Golden Eagle, Golden Hawk, Laredo, Limited and Renegade trims, and the 1981-1985 Jeep Scrambler.

It does not fit the Wrangler or CJ model years outside these ranges. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

The plate is bare steel and must be welded in place, so welding skills are needed. Line up the holes with the frame and check the fit before welding.

What’s included

This is one rear crossmember reinforcing plate.

Not included: welding supplies and any replacement crossmember hardware.

Fitment

VehicleYearsTrims
Jeep CJ51976–1983Base, Golden Eagle, Laredo, Limited, Renegade
Jeep CJ71976–1986Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade
Jeep Scrambler1981–1985Base, Laredo, Renegade, SL, SR

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will RFP7686 fit a 1980 Jeep CJ5?

Yes. The plate fits the 1976-1983 CJ5, and 1980 falls within that range. A 1980 Scrambler is not covered, because the Scrambler years are 1981-1985.

Does the plate need welding?

Yes. The plate is bare steel and must be welded in place. Welding skills are needed, so plan for a welder before fitting the plate.

Can it repair a broken crossmember?

Yes, it can be used to repair a broken crossmember. It can also be fitted to a sound frame to help keep the crossmember from breaking, and it is sized for rear bumpers that carry large tires.

What should be done to the plate after welding?

Bare steel should be cleaned and primed or painted after welding to slow rust. Remove any scale around the welds first, then coat the plate and the frame near the joint so the reinforcement does not corrode from the weld side.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep CJ7 Frame Stiffener on Amazon