Leveling kit vs lift kit explained: factory rake, spacers and torsion keys, tire sizes at 2 to 3 inches, CV angles, towing, load leveling…
Leveling Kits
Leveling kits remove the factory rake that leaves the front of many trucks and SUVs sitting lower than the rear. This category includes coil spring spacers, strut spacers, torsion bar keys and complete suspension leveling kits from ReadyLift, Rough Country, Tuff Country and Bilstein.Compare lift height and method for your vehicle, then open a product page and compare the listings on this page.

Leveling kits lift the nose of a truck or SUV so it sits flat, usually with an inch or two of front lift. You get a cleaner stance and room for a slightly larger tire, without the cost and geometry changes of a full suspension lift.
How a kit lifts depends on what holds up your front end. Coil-sprung solid axles take coil spacers. Independent front ends with struts take strut or coilover spacers. Older GM and Ford trucks with torsion bars use indexed keys. Complete kits swap in adjustable coilovers or matched shocks. Track bars, bump stop spacers and shock extensions handle the side effects on solid-axle Jeeps and Rams.
Shop leveling kits by type
Popular leveling kits
-
Leveling Kits
4 Wheel Parts Factory Bronco Level Lift Kit – 62210K
- Level lift for the 2021 to 2026 Ford Bronco with 2 inches of front lift
- Aluminum coil spring spacers at the front and rear
- Clearance for tires up to 35 inches
- No track bar drop and no bump stops included
- Part number 62210K, black finish
SKU: 4WP62210K -
-
-
-
Coil Spring Spacer
ICON Vehicle Dynamics Ram TRX Coilover Spacer Kit – IVD2122
- Modular coilover spacer for 2021–2026 Ram 1500 TRX and TRX Launch Edition
- Increases ride height by an adjustable amount up to 2.125 inch
- No shock disassembly needed for installation
- CNC machined aluminum with an anodized black finish
- Keeps the active damping system working.
SKU: ICOIVD2122
Leveling kit reference
Lift heights, tire limits and support parts taken from listed kits. Each figure belongs to one part number, so treat it as an example and confirm the numbers for your truck on the product page.
Lift by kit
| Rubicon Express RE1320 / RE1333 | 0.75" coil spacer pair |
|---|---|
| 4 Wheel Parts 62207K | 1" front |
| Rough Country 31300 | 1.5" front, strut spacers |
| Rubicon Express RE1325 / RE1326 | 1.75" coil spacer pair |
| Trail Master TM690 | 2" front strut spacers, 4WD |
| Pro Comp Nitro 61183K | 2.25" front, strut spacers |
| Pro Comp 63156 | 2.5" torsion keys, 2020 GM 2500 HD |
| Bilstein B8 6112 47-234413 | 2.75" front, front lift only |
Support parts
- Adjustable track bars (ARB, JL) re-center a solid axle after lift
- Bump stop spacers (OME FK92, JL) keep shocks from bottoming out
- Shock extensions (Rubicon Express JT7134E) restore shock travel
- Rear lift blocks and U-bolts (Pro Comp 62206K) raise the rear to keep a slight rake
- Upper control arms (Tuff Country 32109) correct ball joint angle
- Torsion key unloading tool (ReadyLift 66-7816A) for safe key swaps
Install method by front end
| Where it goes | Tools and notes | |
|---|---|---|
| Coil spring spacer | Top or bottom of the coil | Unload the coil; spacers come in pairs |
| Strut spacer | Between strut and upper mount | Some upper spacers skip strut teardown |
| Torsion bar key | Replaces the factory key | Unloading tool; set height evenly |
| Coilover or shock kit | Replaces the strut assembly | Adjustable ride height on some |
Tire limits listed
| Belltech 34920 strut spacer | 35" max tire |
|---|---|
| Pro Comp 63156 torsion keys | 33x12.50 max tire |
| Rubicon Express JT7134E | 35" tire size listed |
After installing
- Measure fender height on both sides; even out torsion keys if needed
- Re-aim headlights, since the beams now point higher
- Cycle the steering lock to lock and check tire clearance
- Check CV boot angle and noise on independent front ends
- Re-torque spacer and strut nuts after the first few hundred miles
Lift heights are what the maker lists. Your result depends on spring wear, weight on the front and factory options, so measure before and after.
All Leveling Kits 170 parts
-
Leveling Kits
Tuff Country 2.5 Inch Leveling Kit with Upper Control Arms – 32108
- Tuff Country 2.5 in. front leveling kit with upper control arms, part number T/C32108
- Steel strut spacers for a front-only 2.5 in. lift
- Black finish; bump stops and track bar drop not included
- Fits 2019 to 2020 Ram 1500 models
SKU: T/C32108 -
Leveling Kits
Tuff Country 2.5 Inch Leveling Kit with Uni-Ball Upper Control Arms – 32109
- Tuff Country 2.5 in. front leveling kit with Uni-Ball upper control arms, part number T/C32109
- Steel strut spacers for a front-only 2.5 in. lift
- Black finish; no bump stops and no track bar drop included
- Fits 2019 to 2020 Ram 1500 models
SKU: T/C32109 -
-
-
Leveling Kits
Tuff Country 2″ Leveling Kit with Shock Extensions – 42200
- 2 inch polyurethane coil spring leveling kit with shock extension brackets for 2020–2026 Jeep Gladiator
- Shock extension brackets included
- Tire size up to 37×12.50
- Install takes about 2 to 4 hours
- Lifetime warranty, made in the USA
SKU: T/C42200 -
-
-
What a leveling kit does
Many pickups and SUVs leave the factory with the front slightly lower than the rear to accommodate a load in the bed. A leveling kit raises the front end, typically by roughly one to three inches, so the vehicle sits level and has room for slightly larger tires. It is a lighter, simpler option than a full lift kit and usually keeps the factory suspension geometry.
Types of leveling kits
The method depends on your front suspension design.
- Coil spring spacers sit on top of or under the coil spring on solid-axle or coil-sprung trucks and add ride height at a low cost.
- Strut spacers lift the strut assembly on independent front suspension vehicles that use coil-over struts.
- Torsion bar keys replace the factory key so the torsion bar can be rotated higher, common on many GM and Ford trucks.
- Complete suspension leveling kits pair new shocks or coil-overs, such as Bilstein 6112 units, with the lift hardware for a matched setup.
- Rear spacers and load-level kits restore height at the back where a vehicle sags.
Key points to compare
Check the lift height listed for the front and whether the kit is front only. Look at whether the kit includes extended-length shocks or recommends them, since the factory shock may run out of travel as it is stretched. Spacer material, finish and included hardware matter for durability and corrosion resistance.
Consider tire size. Some kits list a maximum tire size and wheel backspacing, and one torsion bar key set in the sample listings states a 33 inch maximum tire, so read each description for limits.
Note that a leveling kit changes ride and handling slightly. Raised front ends can affect headlight aim, driveshaft angles and CV axle angles on some vehicles.
Installation and alignment
Suspension work involves compressed springs and load-bearing parts. A professional installation is recommended unless you have the proper spring compressors, jack stands and experience. Torque all fasteners to the manufacturer's specifications.
A front alignment is needed after any change in ride height, and you should re-check headlight aim. Lift height, tire size and equipment rules vary by state, so check your local regulations before modifying ride height.
Pairing a leveling kit with tires and shocks
A leveling kit is often the first step in a larger plan, so think about what comes next. Added front height gives room for a modest increase in tire diameter, but check clearance at full steering lock and full compression, where tires can rub on the fender liner, control arms or sway bar. Measure the available space before buying tires instead of assuming a kit alone will clear them.
- Longer front shocks restore full travel if the kit stretches the factory shock close to its limit
- Check that brake lines and ABS wires have enough slack at full droop
- Torsion bar adjustments can be reset later, but never exceed the maximum the vehicle manufacturer allows
- Larger tires change gearing, speedometer reading and braking distance
- Heavier wheels and tires add steering and suspension wear
One common mistake is leveling a truck that regularly carries a heavy bed load or a camper. Because the rear sags under that weight, the front may end up looking high when the vehicle is empty, and handling can feel light. If you tow or haul, test the vehicle loaded and consider rear helper springs or load-level spacers to keep the stance balanced.
Related guides
- Leveling Kit vs Lift Kit: What 3 Inches Really Gets You
- 325/60R20 in Inches: Tire Size Math Made Simple
325/60R20 is 35.4 inches tall and 12.8 wide. The tire size formula, a chart of 24 off-road sizes in inches, speedometer error and regearing…
Popular Leveling Kits brands
- ReadyLift (29)
- Rough Country (28)
- Rubicon Express (12)
- Tuff Country (12)
- Bilstein (9)
- Pro Comp Suspension (9)
- Fabtech (9)
- Trail Master (7)
- Rancho (7)
- TeraFlex (7)
- Daystar (6)
- ICON Vehicle Dynamics (6)
Leveling Kits FAQ
How much can I level my truck?
Typical kits raise the front about one to three inches, but the right amount depends on your suspension design and tires. Staying within the manufacturer's stated lift height helps preserve CV axle and steering angles. Check the manufacturer's stated lift height and your suspension type, since the amount depends on whether you use spacers, keys or a full kit.
Will a leveling kit hurt ride quality?
Spacers generally keep the factory springs and shocks, so the ride feels similar, though the shocks sit closer to full extension. Pairing the lift with correctly sized shocks usually gives the best result.
Do I need an alignment after leveling?
Yes. Changing ride height alters camber, caster and toe, so schedule an alignment right after installation to protect tires and steering feel. The exact figure depends on your suspension type and tires.
Is a leveling kit the same as a lift kit?
No. A leveling kit mainly raises the front to match the rear, while a lift kit raises the whole vehicle and often includes new springs, shocks and control arms for added ground clearance.






















