Suspension Accessories
Suspension accessories are the supporting parts that make a lift or a repair work properly: control arms, track bars, bump stops, spring blocks, U-bolts, sway bar links, shackles and alignment hardware. This category suits Jeep, truck and SUV owners fine-tuning geometry or replacing worn pieces. Brands include Skyjacker, Pro Comp Suspension, TeraFlex and ICON Vehicle Dynamics. Open a product page to read the details, then compare the products below.

Lifting a truck or Jeep moves more than ride height. Axles shift sideways, pinions tip up and links end up too short. These are the arms, bars, springs, stops and hardware that put the suspension back in order, or replace worn pieces on a stock rig.
Coil-sprung rigs such as the Wrangler lean on control arms, track bars, coil springs and bump stop extensions. Leaf-sprung trucks use add-a-leafs, blocks, U-bolts, shackles and center pins. Sway bar links, disconnects and bushings sit in between. Every listing names a lift range or a fitment, so match that to your build first, then compare bushing type, adjustability and finish.
Shop suspension accessories by part type
More part types (10)
Popular suspension accessories
-
-
Control Arms
Pro Comp Pro Series Front Upper Control Arms – 52003B
- Pro Series front upper control arms for the 2019-2021 Ford Ranger
- High angle ball joint on tube arms
- PTMEG bushings and helix grooved pivot points
- Sealed dust cap for long-term quiet pivot performance
- Part number 52003B
SKU: EXP52003B -
-
-
Control Arm Drop Bracket
Rubicon Express Control Arm Drop Brackets – RE9900
- Fits the Jeep Cherokee (XJ), 1984 to 2001
- Relocates the upper and lower control arms about 3 inches lower and 1/2 inch forward
- Recommended for 5.5 inch lifts
- Black powder coat finish
- Part number RE9900, UPC 614901442243
SKU: R/ERE9900 -
Control Arms
Pro Comp Pro Series Front Upper Control Arms – 51040B
- Front upper control arm with a high angle ball joint
- PTMEG bushings and helix grooved pivot points with a sealed dust cap
- Fits 2007 to 2016 Chevrolet and GMC 1500 trucks and SUVs
- Corrected geometry and alignment after a lift
- Part number 51040B
SKU: EXP51040B -
-
Suspension accessory reference
Quick comparisons for the parts you meet most often after a lift. Figures in the last card come from individual listings in this category; check the product page for your exact part number.
Coil-sprung vs leaf-sprung axles
| Coil-sprung | Leaf-sprung | |
|---|---|---|
| Ride height set by | Coil springs and spacers | Add-a-leafs, blocks, new packs |
| Axle located by | Control arms or radius arms | The leaf spring itself |
| Side-to-side centering | Track bar or Panhard rod | Built into the spring mounts |
| Pinion angle correction | Adjustable arms, drop brackets | Degree shims or tapered blocks |
| Typical extra hardware | Bump stop extensions, end links | U-bolts, shackles, center pins |
What to measure before ordering
- Actual lift height, measured at the fender or frame before and after
- Front and rear, and driver or passenger side, for arms and brackets
- Axle tube diameter and spring width before choosing U-bolts
- U-bolt thread size, inside width and length past the block and spring
- Leaf spring center pin diameter and length
- Sway bar diameter for bushings (listed in mm, such as 27 mm)
- Axle make and type, since spindles and brackets are axle specific
Bushing and joint types
| Rubber | Polyurethane | Heim / rod end | |
|---|---|---|---|
| Ride comfort | Softest | Firmer | Firmest |
| Noise and vibration | Best isolation | Some transfer | Most transfer |
| Deflection under load | Most | Less | Almost none |
| Upkeep | Replace when cracked | Grease if greasable | Inspect, adjust, replace |
| Common use | Factory arms | Shackles, sway bars, arms | Adjustable arms, track bars |
Lift ranges stated on listings
| Rubicon Express RE1689 track bar | 0–8" of lift |
|---|---|
| Rubicon Express RE9900 drop brackets | For 5.5" of lift |
| Rubicon Express RE1152 end links | JL with 3.5–4.5" of lift |
| Rough Country 1186 sway bar disconnects | 4–6" of lift |
| Cognito 110-90901 traction bars | 0–4" of lift |
| TeraFlex 1900000 T-case lowering kit | 1/2" drop |
| ReadyLift 47-5005 Tundra diff drop | About 1" drop for CV angles |
Lift ranges and fitment vary by part number. Confirm your year, model and actual lift height on the product page before ordering, and plan for an alignment after changing arms or track bars.
All Suspension Accessories 1,625 parts
-
Coil Springs
Rock Krawler 3.5 Inch Lift Heavy-Duty Coil Springs
- Rock Krawler 3.5 inch heavy-duty rear coil spring, part number RK02002
- Fits 2007–2016 Jeep Wrangler JK, two- and four-door models
- Preset to minimize settling, shot peened and powder coated black
- Actual lift varies with vehicle accessories and axle positioning
SKU: RKSRK02002 -
Coil Springs
Rock Krawler 3.5 Inch Lift Heavy-Duty Coil Springs
- Rock Krawler 3.5 inch heavy-duty front coil spring, part number RK02001
- Fits 2007–2016 Jeep Wrangler JK, two- and four-door models
- Preset to minimize settling, shot peened and powder coated black
- Actual lift varies with vehicle accessories and axle positioning
SKU: RKSRK02001 -
Coil Springs
ARB Old Man Emu Coil Spring – 2936
- Heavy load Old Man Emu coil spring for the 1999–2001 Jeep Cherokee XJ and 1999–2004 Jeep Grand Cherokee WJ
- Part number 2936, UPC 9319092023516
- Cherokee covers Classic, Limited, SE and Sport; Grand Cherokee covers Laredo, Limited, Overland, Special Edition and Sport
- Designed for control under a heavier load
SKU: ARB2936 -
-
-
Coil Springs
ARB Old Man Emu Coil Spring – 2922
- Medium duty Old Man Emu coil spring for R50 generation Nissan Pathfinder and 2004 Pathfinder Armada
- Part number 2922, UPC 9319092023370
- Fits Pathfinder LE, SE and XE trims, plus Armada LE and SE trims.
- Designed for control and ride comfort under a load
SKU: ARB2922
What belongs in this category
A lift kit rarely arrives complete. Raising a vehicle changes axle position, driveshaft angles and link lengths, and the parts here correct those side effects or replace pieces that wear out. The range runs from small hardware such as U-bolts and leaf spring center pins to larger components such as adjustable control arms, radius arms, spindles and frame stiffeners.
- Geometry correction: track bars, track bar brackets, control arm drop brackets and caster or camber kits bring axle position and alignment back toward factory targets after a lift.
- Springs and spacing: coil springs, add-a-leaf packs, lift blocks and coil spring isolators set ride height and load behavior.
- Travel and protection: bump stops limit compression travel so the axle does not hit the frame or the shock bottoms out.
- Linkage and bushings: sway bar links (fixed or disconnect), control arm bushings and shackle kits handle articulation and noise.
How to choose
Start with the problem you are solving. A front track bar that no longer centers the axle after a 3-inch lift needs an adjustable bar or a relocation bracket, not a different spring. A driveline vibration on a leaf-spring truck points to pinion angle, which is handled with degree shims, a carrier bearing drop or a transfer case lowering kit depending on the setup.
Match the part to your lift height. Many listings state a range, such as a track bar for 0 to 3.5 inches of lift, and staying inside that range keeps the geometry sensible. Also note the position (front or rear), the side if it matters, and whether the part is a direct fit or a universal piece that needs fabrication.
Specs worth comparing
- Block height, taper and pin size for lift blocks, and U-bolt thread size and length to match the block and axle tube.
- Material and construction: forged or fabricated steel versus cast, and the bushing type (rubber, polyurethane or heim joint) with its trade-off between comfort and precision.
- Adjustability: length-adjustable arms and bars simplify centering the axle and setting caster.
- Finish: powder coat or e-coat helps resist corrosion on parts that live under the vehicle.
Installation and fitment notes
These are safety-related parts, so torque every fastener to the manufacturer's specification, replace stretched or damaged hardware, and recheck torque after the first few hundred miles. A professional alignment is recommended after changing control arms, track bars or caster hardware, and a driveline check is wise after changing pinion angle. Confirm fitment for your exact year, make and model, and read the manufacturer's specifications before choosing, since axle brands, cab styles and lift heights change what fits. Lift and ride-height rules vary by state.
Common mistakes to avoid
The most frequent error is treating each part in isolation. A longer track bar solves lateral axle position, but it does nothing for a pinion angle that now points too high. Make a short list of symptoms first: wandering, vibration, clunks over bumps, tire rub or uneven wear. Then match each symptom to the part that addresses it.
Another mistake is mixing hardware grades. U-bolts, shackle bolts and control arm bolts carry real loads, so reuse is risky when threads are stretched or the plating has worn away. Keep a record of what you installed and the torque values used, because it makes later troubleshooting much faster. If a noise appears after installation, recheck the fasteners before assuming a part is faulty, since loose hardware is the most common cause.
Popular Suspension Accessories brands
- ARB 4x4 Accessories (209)
- Rubicon Express (192)
- Pro Comp Suspension (160)
- Skyjacker (146)
- Crown Automotive (110)
- TeraFlex (110)
- Fabtech (95)
- Energy Suspension (78)
- Omix-Ada (50)
- Icon Suspension (42)
- Tuff Country (42)
- Rock Krawler (42)
Suspension Accessories FAQ
Do I need new control arms with a lift?
It depends on lift height and vehicle. Small lifts often work with factory arms, while taller lifts can leave the axle out of position or the pinion angle off. Adjustable aftermarket arms let you correct this. Check the lift kit maker's recommendations for your height.
What does a bump stop do?
A bump stop limits how far the suspension can compress, keeping the axle, tire or shock from hitting the frame or body. Taller lifts and bigger tires usually need extended stops, since the factory travel limits no longer match the new geometry.
When should I use a lift block instead of a spring?
Lift blocks are a simple way to raise a leaf-spring rear axle, but they can add axle wrap and change pinion angle. Many owners pair them with tapered blocks or shims. A new spring or add-a-leaf changes ride quality more directly.
Do I need an alignment after installing these parts?
Yes, in most cases. Control arms, track bars and caster or camber kits all change axle position and steering geometry. Have the alignment checked by a qualified shop after installation and again after the parts settle.

























