Fog/Driving Light Wiring Kit
Showing 13–24 of 35 resultsSorted by popularity
-
Fog/Driving Light Wiring Kit
Rugged Ridge 2-Light Installation Wiring Harness with Rocker Switches – 15210.72
Fog/Driving Light Wiring KitRugged Ridge 2-Light Installation Wiring Harness with Rocker Switches – 15210.72
- Two-light installation wiring harness with rocker switches, part number 15210.72
- Includes wiring harness, relay and illuminated dash switch
- Universal fit, not tied to a model year
SKU: RUG15210.72 -
Fog/Driving Light Wiring Kit
Rugged Ridge 3-Light Installation Wiring Harness – 15210.71
- Universal fit three-light installation wiring harness, Rugged Ridge part number 15210.71
- Includes wiring harness and relay
- Pre-terminated ends and 14 gauge wire
- Allows wiring of multiple light locations
SKU: RUG15210.71 -
-
Fog/Driving Light Wiring Kit
PIAA Wiring Harness Up To 100W For Dual Light Systems (LR18) X 2 – 34210
Fog/Driving Light Wiring KitPIAA Wiring Harness Up To 100W For Dual Light Systems (LR18) X 2 – 34210
- PIAA 34210 wiring harness, complete with switch, relay, fuse and light connectors
- Supports loads up to 100W
- Built for dual light systems (LR18 x 2)
- Universal fit, not written for a specific vehicle
SKU: PIA34210 -
-
-
Fog/Driving Light Wiring Kit
Hella Wiring Harness for Rallye 4000 Lights – 148541001
- Hella wiring harness for Rallye 4000 lights, part number 148541001
- Lights are not included; the harness is a separate purchase
- Rallye 4000 lights use high-output 100 watt H1 bulbs, metal housings and glass lenses
- Universal fit; not vehicle-specific
SKU: HLA148541001 -
-
Why a wiring kit matters
Auxiliary lights draw more current than a switch or factory wire is meant to carry. A harness uses a relay, so the switch only triggers a low current and the relay passes the high current directly from the battery, protected by a fuse near the power source. This helps prevent melted wires, blown fuses and voltage drop that makes lights look dim.
What a kit contains
- A relay, usually a 12 volt automotive type
- An inline fuse or fuse holder
- Power and ground leads sized for the load
- Connectors that plug into the lights, or bare leads for splicing
- A switch or switch leads
Some harnesses are made for a specific pair of lights, such as Rigid D2 pods or large light bars, while others are generic two-light kits.
Matching the kit to the lights
Count the lights and add up their rated current. The harness should be rated above that total. Wire gauge matters, since thinner wire carries less current and longer runs lose more voltage. Look for the connector type on your lights, such as Deutsch or a proprietary plug, so you do not have to cut or splice. For longer light bars, use a harness made for that size, since it will have heavier wire.
Installation notes
Disconnect the battery before starting. Mount the relay in a dry location, route wiring away from heat and moving parts, and use grommets where wires pass through the firewall. Fuse the power lead close to the battery. Seal outdoor connections with heat-shrink or dielectric grease to resist moisture and corrosion. Use a clean, bare-metal ground. If you are not comfortable with automotive wiring, a qualified installer can do it safely. Lighting laws differ by state, so check local rules about auxiliary lights on public roads and whether they must be covered when driving on pavement.
Compatibility
Fitment depends on the lights you own and, for vehicle-specific kits, on year, make and model. Check product details and manufacturer instructions before choosing. When splicing is needed, use quality crimp connectors or solder with heat shrink, not twist-and-tape joints, and secure the harness with ties every foot or so to keep it from vibrating loose.
Common mistakes to avoid
Do not tap power from a low-current circuit such as a parking light wire without a relay, and do not use a harness whose fuse is rated higher than the wire can carry. Keep wire runs as short as practical, and avoid running power wires along sharp edges. Check that every connection is tight, because a loose terminal creates heat. Protect wires with split loom or braided sleeve, especially near the engine bay. Always label the switch wiring, so future troubleshooting is easy. If lights flicker or dim, check the ground connection first. Test the full circuit with the engine running to confirm the voltage at the lights is steady.
Weatherproofing deserves attention in off-road use. Water crossings, mud and pressure washing all test connectors, so use sealed connectors and drip loops where wires drop below the connection point.
Popular Fog/Driving Light Wiring Kit brands
- Rigid Industries (15)
- Rugged Ridge (7)
- Pro Comp Suspension (4)
- Baja Designs (3)
- KC HiLites (3)
- Hella (2)
- Piaa Lighting (2)
- Omix-Ada (1)
- T-Rex Grilles (1)
- Truck-Lite (1)
- ARB 4x4 Accessories (1)
Fog/Driving Light Wiring Kit FAQ
Do I need a relay for off-road lights?
Yes, in most cases. A relay lets the battery feed the lights directly through a fuse, while the switch only carries a small control current. This protects switches and factory wiring from overload.
What fuse size should I use?
Pick a fuse rated slightly above the lights' combined current draw and below the wire's rating. Follow the light and harness manufacturer's instructions, and place the fuse near the battery.
Can I use one harness for several lights?
Only if the harness is rated for the total current of all lights. Check the relay and wire gauge rating, and use a kit designed for the number of lights, or a heavier setup.









