Select your vehicle

Light Mounting Brackets & Cradles

Brackets, cradles, and mounts that hold auxiliary lights on a roof, windshield, hood, bumper, or roll bar. Rigid Industries, Rugged Ridge, KC HiLites, and Go Rhino all make mounting hardware here, in universal and vehicle-specific designs. A solid mount keeps a light aimed and quiet over washboard roads. Use the subcategories to narrow by mounting location, then compare the products below.

Billet aluminum A-pillar light mounts for the Ford Bronco

Good lights on a bad bracket shake, drift out of aim and eventually break off. This category is the hardware between your lights and the vehicle: A-pillar, cowl, hood, roof, bumper, grille and tube mounts, plus universal plates and clamps for custom setups on Jeeps, Broncos, trucks and UTVs.

Start with where the light goes, then what light it is. Roof and windshield mounts carry long bars up high. Fog, bumper and grille mounts sit low for close and wide light. A-pillar, hood and cowl brackets hold pods or short bars near the hinge line. Tube clamps fit roll bars and cages by outside diameter, and many brackets are sized for one light series or bar length.

290Parts listed
38Brands
10Mount locations
1.65–3"Tube clamp sizes listed
3" x 3"Common cube light size
6–52"Bar lengths in listings

Shop light mounts by location

Popular light brackets and mounts

Light mount sizing reference

Sizes and fitment taken from mounts in this category. Measure your tube and check the light's mounting style before you order.

Tube clamp sizes

Baja Designs 617608 horizontal mount1.75" tube
Baja Designs 617510 A-pillar mount2" tube
Baja Designs 617710 vertical mount2" tube
Rough Country 70171 clamps1.65–2" tube
Rough Country 70172 clamps2.5–3" tube, rotate 360 degrees
Measure your tubeCircumference / 3.14 = outside diameter

Vehicle-specific mounts listed

  • 2021–2022 Ford Bronco 2- and 4-door A-pillar mounts (4 Wheel Parts 52900B)
  • Wrangler JL cowl and A-pillar brackets: Rigid, Rock Slide, DeeZee, Artec
  • Wrangler JK grille mounts for Trail 6 lights (JW Speaker 8200573)
  • Chevy 1500/2500/3500 grille mount for a 30" bar (Baja Designs 447588)
  • Bumper-specific plates, such as ICON 95155 for ICON Impact bumpers

What each mount holds

Go Rhino 732230T center hood mountOne 3" x 3" cube
Go Rhino 732060T center hood mountTwo 6" single-row bars
Go Rhino 732020T center hood mountOne 10" single-row bar
RT Off-Road RT28082 hood brackets21.5" bar (RT28083)
Rough Country 70172 clamp pairCubes or one 30" bar across both
Rigid 46520 fog mount kitTwo D-Series plus a 30" SR-Series
Go Rhino 599501T hardtop rear mountCubes, 6" bars or a 20–40" bar
Fishbone FB21058 bracket52" bar

Mounting styles

HoldsWatch for
Single center boltPods and cubesCan rotate out of aim if under-tightened
Side-mount bracketsLight barsBar series and end bracket style
CradleOne light sizeExact housing size
Rail or PicatinnyPods on a rail systemRail spec and clamp style
Hinge or cowl bracketPods, short barsUses factory bolts; retorque

Most mounts ship without lights. Many states limit auxiliary light use on public roads, so check local rules and cover off-road lights on pavement.

All Light Mounting Brackets & Cradles 290 parts

Showing 1–12 of 290 resultsSorted by popularity

Why the mount matters

An auxiliary light is only as good as what holds it. A flimsy bracket can vibrate loose, drift out of aim, and fatigue until the light is lost on the trail. A good mount is rigid, sized for the housing, and made from a material that survives road salt and moisture, typically stainless steel or powder-coated steel or aluminum.

Mounting locations

  • Roof and windshield: mounts that clamp to roof racks or the windshield frame place lights high for long-range visibility and less glare off the hood.
  • A-pillar: bracket pairs that bolt to the hinge area for pod lights, common on Jeeps and trucks.
  • Hood and ditch light: brackets that use hood hinge bolts, aiming lights into the corners of the road.
  • Bumper: brackets and cradles that fit bumper tabs, fog openings, or tube bumpers.
  • Roll bar and tubular: clamps sized for specific tube diameters, such as 1.75 inch or 2 inch.
  • Universal: flat plates, stud bases, and bar mounts for custom installs.

Matching the bracket to the light

Check the light's mounting style before choosing a bracket. LED bars typically use T-slot or stud mounts on the housing, and pods and cubes often use a single center bolt or a cradle that wraps the body. A cradle is made for one light size, so match the nominal size, such as 4 inch round or a specific bar length. Bars also come in side-mount, surface-mount, and flush-mount versions, and the hardware is not always interchangeable. Confirm the bracket lists your light series.

Installation tips

Use all supplied hardware and thread locker where recommended, and tighten to the stated torque so the clamp does not crush or slip. Route wiring away from sharp edges and heat, and leave slack for any moving part such as a hood. Aim lights after installation, at night on a flat surface, and recheck after the first rough drive. Some brackets use existing factory bolts, while others need drilling, so plan before cutting into paint or sheet metal.

Lights are sold separately from most mounts. Auxiliary light use on public roads is regulated in many states, so check local rules and cover lights when driving on pavement. Always confirm fitment for your exact year, make, and model with the manufacturer's specifications.

Common pairings and mistakes

Pair a bracket with a light whose weight it can carry. A long LED bar on a tiny single-bolt mount will bounce, so use at least two mounting points or a bracket made for that length. Stainless steel resists corrosion, while plain steel needs its powder coat intact, so touch up chips before rust starts. Avoid drilling the roof or hood unless the instructions call for it, and seal any hole you do make. Keep lights clear of the radiator opening and airflow paths. If the mount sits near an antenna, a mirror, or a camera sensor, check that the beam does not reflect into the driver's view. Inspect bolts for looseness after rough trails.

Keep a small kit of spare stainless bolts, nylon-insert nuts, and rubber isolators on hand, since vibration works hardware loose over washboard roads and a missing fastener is easy to replace on the spot.

Popular Light Mounting Brackets & Cradles brands

Light Mounting Brackets & Cradles FAQ

Do light brackets come with the light?

Usually not. Many mounts are listed separately from the light, and some product notes say lights are sold separately. Check that the bracket matches the light's size and mounting style, and that the hardware is included.

Which mounting location is best for an LED bar?

It depends on the use. Roof locations give the longest reach with less glare, while bumper and hood spots light the area near the vehicle. Local rules and your vehicle's design also limit what is practical, so consider the legality in your state.

What size roll bar clamp do I need?

Measure the outside diameter of your roll bar or tube. Common sizes include 1.75 inch and 2 inch, and clamps are made for specific diameters. A clamp that is the wrong size will slip or damage the tube.

Can I use a hood mount on any vehicle?

No. Hood and ditch light brackets are usually designed around specific hinge bolt locations and body shapes. Confirm that the bracket lists your vehicle, or choose a universal mount if you need to fabricate your own placement.