Suspension Accessories
Showing 37–48 of 1625 resultsSorted by popularity
-
-
Suspension Control Arm Link
Trail Gear 1.25 Inch Creeper Joint – 110766-KIT
- Weld-on 1.25 inch creeper joint kit for building suspension links
- Forged outer shell with 8620 tool steel flex ball
- Polyurethane bushings and hardened steel washers
- Up to 40 degrees of movement when used with spacers
- Part number TGI110766-KIT
SKU: TGI110766-KIT -
Suspension Control Arm Link
Trail Gear 1 Inch Creeper Joint – 110771-KIT
- Forged 1 inch creeper joint for suspension links and rod ends
- Forged outer shell with an 8620 tool steel flex ball
- Polyurethane bushings and hardened steel washers
- Up to 40 degrees of movement when used with spacers
- Threaded grease fitting and jam nut included
- Part number TGI110771-KIT
SKU: TGI110771-KIT -
Bump Stops
Timbren Active Off-Road Rear Bumpstops – ABSTRFK
- Rear Active Off-Road bump stop for Toyota Tacoma
- Also fits 2015–2016 Chevrolet Colorado and GMC Canyon
- Includes a U-bolt flip kit for more ground clearance
- Progressive-rate action with a natural rubber compound
- Lifetime warranty and satisfaction guarantee
SKU: T/IABSTRFK -
Bump Stops
Timbren Active Off-Road Rear Bumpstops – ABSTORLC2
- Rear Active Off-Road bump stop for Toyota Land Cruiser 200 series
- Fits 2008–2011 and 2013–2021 Lexus LX570 and Toyota Land Cruiser Base trims
- Progressive-rate action at the end of axle travel
- Natural rubber compound
- Lifetime warranty and satisfaction guarantee
SKU: T/IABSTORLC2 -
Bump Stops
Timbren Active Off-Road Rear Bumpstops – ABSOSR
- Rear Active Off-Road bump stop for 2015–2016 Colorado, Canyon, Nissan Frontier and Toyota Tundra
- Progressive-rate action at the end of axle travel
- Natural rubber compound built for continued use after long off-road sessions
- Lifetime warranty and satisfaction guarantee
- Natural rubber compound with progressive-rate action
SKU: T/IABSOSR -
Bump Stops
Timbren Active Off-Road Front Bumpstops – ABSGMFCC
- Front Active Off-Road rubber bump stop for 2015–2016 Chevrolet Colorado and GMC Canyon
- Progressive-rate springs for smooth, quiet engagement
- Natural rubber compound designed to outlast factory stops
- Lifetime warranty and satisfaction guarantee
- Listed trims include LT, WT and Z71 for the Colorado
SKU: T/IABSGMFCC -
Bump Stops
Timbren Active Off-Road Bumpstops – ABSJFTJ
- Rubber active off-road bump stop for the Jeep Wrangler TJ front or rear
- Also fits JK, JL and Gladiator front positions
- Progressive-rate action with smooth, quiet engagement
- Natural rubber compound
- Lifetime warranty and satisfaction guarantee
SKU: T/IABSJFTJ -
Transfer Case Lowering Kit
TeraFlex Transfer Case Lowering Kit – 1900000
- Transfer case lowering kit that drops the case 1/2 inch
- Includes six lowering spacers and all necessary hardware
- Designed to reuse the factory transfer case bolts
- Helps reduce driveshaft vibration on a lifted TJ
- Shift linkage adjustment may be necessary
- Part number TER1900000
SKU: TER1900000 -
Control Arms
TeraFlex Sport Flexarm Front Lower Control Arms – 1253000
- Sport Flexarm front lower control arms, TeraFlex 1253000
- For JL and JLU Wrangler models with 1.5 to 3.5 inch lifts
- Bolts to the factory control arm mounting locations
- Maintenance-free, dependable bushings installed
- Sold in pairs
SKU: TER1253000 -
Bump Stops
TeraFlex SpeedBump Bumpstop Kit – 1958250
- SpeedBump composite bump stop kit for 2007–2018 Jeep Wrangler JK
- Progressive closed-cell microcellular polyurethane stops
- Self-lubricating Delrin acetal resin shaft
- Includes front and rear SpeedBump stops and front strike pads
- Fits JK models with 2.5 inch of lift.
SKU: TER1958250 -
What belongs in this category
A lift kit rarely arrives complete. Raising a vehicle changes axle position, driveshaft angles and link lengths, and the parts here correct those side effects or replace pieces that wear out. The range runs from small hardware such as U-bolts and leaf spring center pins to larger components such as adjustable control arms, radius arms, spindles and frame stiffeners.
- Geometry correction: track bars, track bar brackets, control arm drop brackets and caster or camber kits bring axle position and alignment back toward factory targets after a lift.
- Springs and spacing: coil springs, add-a-leaf packs, lift blocks and coil spring isolators set ride height and load behavior.
- Travel and protection: bump stops limit compression travel so the axle does not hit the frame or the shock bottoms out.
- Linkage and bushings: sway bar links (fixed or disconnect), control arm bushings and shackle kits handle articulation and noise.
How to choose
Start with the problem you are solving. A front track bar that no longer centers the axle after a 3-inch lift needs an adjustable bar or a relocation bracket, not a different spring. A driveline vibration on a leaf-spring truck points to pinion angle, which is handled with degree shims, a carrier bearing drop or a transfer case lowering kit depending on the setup.
Match the part to your lift height. Many listings state a range, such as a track bar for 0 to 3.5 inches of lift, and staying inside that range keeps the geometry sensible. Also note the position (front or rear), the side if it matters, and whether the part is a direct fit or a universal piece that needs fabrication.
Specs worth comparing
- Block height, taper and pin size for lift blocks, and U-bolt thread size and length to match the block and axle tube.
- Material and construction: forged or fabricated steel versus cast, and the bushing type (rubber, polyurethane or heim joint) with its trade-off between comfort and precision.
- Adjustability: length-adjustable arms and bars simplify centering the axle and setting caster.
- Finish: powder coat or e-coat helps resist corrosion on parts that live under the vehicle.
Installation and fitment notes
These are safety-related parts, so torque every fastener to the manufacturer's specification, replace stretched or damaged hardware, and recheck torque after the first few hundred miles. A professional alignment is recommended after changing control arms, track bars or caster hardware, and a driveline check is wise after changing pinion angle. Confirm fitment for your exact year, make and model, and read the manufacturer's specifications before choosing, since axle brands, cab styles and lift heights change what fits. Lift and ride-height rules vary by state.
Common mistakes to avoid
The most frequent error is treating each part in isolation. A longer track bar solves lateral axle position, but it does nothing for a pinion angle that now points too high. Make a short list of symptoms first: wandering, vibration, clunks over bumps, tire rub or uneven wear. Then match each symptom to the part that addresses it.
Another mistake is mixing hardware grades. U-bolts, shackle bolts and control arm bolts carry real loads, so reuse is risky when threads are stretched or the plating has worn away. Keep a record of what you installed and the torque values used, because it makes later troubleshooting much faster. If a noise appears after installation, recheck the fasteners before assuming a part is faulty, since loose hardware is the most common cause.
Popular Suspension Accessories brands
- ARB 4x4 Accessories (209)
- Rubicon Express (192)
- Pro Comp Suspension (160)
- Skyjacker (146)
- Crown Automotive (110)
- TeraFlex (110)
- Fabtech (95)
- Energy Suspension (78)
- Omix-Ada (50)
- Icon Suspension (42)
- Tuff Country (42)
- Rock Krawler (42)
Shop Suspension Accessories by type
- Coil Springs (338)
- Control Arms (264)
- Bump Stops (169)
- Control Arm Bushing (124)
- Axle U-Bolt (107)
- Sway Bar Link - Non Disconnect (89)
- Track Bar (85)
- Add A Leaf (62)
- Axle U-Bolt Kit (54)
- Sway Bar Link - Disconnect (39)
- Coil Spring Isolator (39)
- Alignment Caster/Camber Kit (31)
- Sway Bar Bushing (22)
- Transfer Case Lowering Kit (17)
- Leaf Spring Center Pin (14)
- Control Arm Drop Bracket (14)
- Carrier Bearing Drop (6)
- Radius Arm (6)
- Sway Bar Bracket (5)
- Bump Stop Spacer (3)
- Leaf Spring Bump Stop (3)
- Suspension Control Arm Link (3)
- Differential Drop Bracket (2)
- Leaf Spring Shackle (2)
- Lift Hardware Kits (2)
- Shock Mounting Brackets (1)
Suspension Accessories FAQ
Do I need new control arms with a lift?
It depends on lift height and vehicle. Small lifts often work with factory arms, while taller lifts can leave the axle out of position or the pinion angle off. Adjustable aftermarket arms let you correct this. Check the lift kit maker's recommendations for your height.
What does a bump stop do?
A bump stop limits how far the suspension can compress, keeping the axle, tire or shock from hitting the frame or body. Taller lifts and bigger tires usually need extended stops, since the factory travel limits no longer match the new geometry.
When should I use a lift block instead of a spring?
Lift blocks are a simple way to raise a leaf-spring rear axle, but they can add axle wrap and change pinion angle. Many owners pair them with tapered blocks or shims. A new spring or add-a-leaf changes ride quality more directly.
Do I need an alignment after installing these parts?
Yes, in most cases. Control arms, track bars and caster or camber kits all change axle position and steering geometry. Have the alignment checked by a qualified shop after installation and again after the parts settle.











