Fabrication & Tools
Showing 385–396 of 504 resultsSorted by popularity
-
Axle Truss
G2 Dana 30 Front Axle Top Truss – 68-2050-1
- Top truss for the Dana 30 front axle on 2007-2018 Jeep Wrangler JK
- Heavy-duty steel: 1/4 inch main components, 1/8 inch reinforcement plates
- Unpainted; welding required, including to the cast center section
- Fits 2-door and 4-door models; includes top truss only
SKU: G/268-2050-1 -
Axle Truss
G2 Rear Dana 44 Truss – 68-2052-1
- G2 rear Dana 44 axle truss, part 68-2052-1, for the Jeep JK
- Heavy-duty steel, 1/4 inch components and 1/8 inch plates
- Intended for JKs with at least some lift; check clearance on lower-lift vehicles
- Welding required; upper link mount sold separately
SKU: G/268-2052-1 -
-
-
-
-
Heim Joints
Rock Krawler Small Krawler Joint Raceway – RK00221
- Rock Krawler RK00221 replacement joint raceways for small Krawler joints
- Fits 3/4 inch and 7/8 inch joints and a 2 inch outside diameter housing
- Black poly construction, sold as a pair, made in the USA
- Newer style joints need the Small joint tool, Part# RK04034
SKU: RKSRK00221 -
-
Shock Mounts
Flat Shock Tabs
- Artec Industries Flat Shock Tabs, Short length, comes as a pair
- CNC laser cut from 1/4-inch steel with a 1/2-inch hole for standard shocks
- Dimension from hole center to flat bottom: 1.125 inch
- Tapered bottom half adds surface area for welding
- Part number not listed; no vehicle fitment listed
SKU: A/ITB1019 -
Gussets & Tabs
Artec Inner Frame Bracket – BR1018
- Universal inner frame bracket for the front driver or rear passenger position
- 1/4 inch thick boxed steel with a 25 degree angle
- 2.625 inch mounting width and 9/16 inch bolt hole
- Tapered sides and top grease fitting access
- Single bracket with a skid plate for the joint, bare steel
SKU: A/IBR1018
What you will find here
Fabrication and tools covers the small parts that custom suspension and chassis work depends on. Rod ends and flex joints let links articulate, tube adapters join tubing to those joints, gussets and tabs reinforce brackets, and perches and shock mounts attach springs and shocks to axles and frames. Specialty tools such as joint presses, torsion key unloaders, spindle nut sockets and installation tools round out the category.
Rod ends and flex joints
Johnny Joint style flex joints use a bushing in a threaded housing, usually with urethane, and allow articulation while absorbing vibration. Heim joints, often called rod ends, use a spherical ball and are more rigid and precise, but they transmit more noise and need regular inspection. Left-hand and right-hand threaded ends, paired with jam nuts, let you adjust link length without removing the link. Misalignment spacers let a joint swing through its full range without binding.
Specs to match
- Thread size and direction: for example 3/4 inch versus 1-1/4 inch, left or right hand.
- Housing outside diameter and mounting width: this must match the tube or bracket.
- Bolt hole size: sets the bolt diameter through the joint.
- Weld-on or threaded: some adapters and joints must be welded.
- Serviceability: some joints grease through a fitting, and some can be rebuilt.
Safety and workmanship
Suspension links, cage components and steering parts are safety-critical. Welding should be done by someone qualified, using correct tube wall thickness, proper penetration and heat control. Use proper-grade hardware, tighten to specification, and fit jam nuts correctly with full thread engagement. Inspect joints regularly for play and cracks. For steering and suspension work you are unsure about, have a professional fabricator build and inspect it.
Think about the complete link before buying individual parts. A control arm or link is built from two ends, a tube and the hardware, and every piece must match: the thread of the ends has to match the tube adapter, and the bolt diameter must match the mounts on the axle and frame. Measure the center-to-center length you need with the suspension at ride height and again at full droop and full compression, so the ends never bind or run out of thread engagement.
The tools in this category make jobs safer and tidier. Joint presses and installation tools prevent damaged bushings, and a spindle nut socket or torsion key tool does a job that is awkward and risky with improvised tools. Brackets, gussets and tabs should be welded with clean, fully fused beads and placed to spread loads into the surrounding structure rather than concentrating stress on a single spot. Never grind or drill structural components without understanding how that changes their strength. Keep a record of the torque used on every fastener and recheck after the first trail outing.
Keep spare hardware on hand for trail repairs, including a few jam nuts, grade-rated bolts, nylon-insert locknuts and extra misalignment spacers, since these small parts are easy to lose and hard to improvise. Mark the final position of each adjustable end with paint so you can see at a glance if anything has turned. Store rod ends clean and lightly oiled, because rust inside a spherical bearing causes binding and premature wear.
Compatibility
Many items here are universal, so fitment depends on your design. Confirm dimensions and thread specifications from the manufacturer before choosing a product below.
Popular Fabrication & Tools brands
- Artec Industries (94)
- Rubicon Express (72)
- RockJock 4x4 (56)
- Currie (52)
- Trail Gear (44)
- TeraFlex (31)
- Fabtech (26)
- Blue Torch Fabworks (23)
- Rock Krawler (18)
- Mountain Off Road Enterprises (15)
- Poison Spyder Customs (13)
- Pro Comp Suspension (13)
Shop Fabrication & Tools by type
- Shock Mounts (72)
- Gussets & Tabs (59)
- Flex Joints, Rod Ends & Jam Nuts (116)
- Flex Joints (62)
- Tube Adapters (26)
- Brackets, Gussets & Tabs (80)
- Jam Nuts (17)
- Leaf Spring Perch (17)
- Tubing & Tube Adapters (12)
- Misalignment Spacers & Washers (9)
- Shock Absorber Wrench (8)
- Joint Tools (6)
- Roll Cage Gusset (7)
- Leaf Spring Accessories (3)
- Link Arm End (6)
- Nut-Sert Installation Tool (1)
- Sockets (3)
- Tool Bits (2)
- Specialty Tools (4)
- Drill Bits (0)
- Siphons (2)
- Hand Tools (2)
- Torsion Key Unloading Tool (2)
- Spindle Nut Socket (2)
- Oil Screen Installation Tool (0)
- Hose Cutter (1)
- Roll Cage Accessories (1)
- Knuckle Pull Scale (1)
- Garage Tools (1)
Fabrication & Tools FAQ
What is a Johnny Joint?
A Johnny Joint is a trademarked style of flex joint that places a bushing inside a threaded housing so a link or arm can pivot and twist. It is quieter than a heim joint and widely used in control arms and track bars.
What is the difference between a heim joint and a flex joint?
A heim joint uses a metal spherical bearing for precise, rigid movement, but it can be noisy and needs inspection. A flex joint uses a bushing, often urethane, which dampens noise and vibration while still letting the link articulate.
Why do rod ends come in left-hand and right-hand threads?
Pairing one left-hand and one right-hand end lets you turn a single link tube to lengthen or shorten it without removing either end. Jam nuts then lock the adjustment so the threads cannot back out.
Do I need to weld tube adapters?
Many tube adapters and weld-in joints must be welded to the tubing, while others thread in. Check the product description. Welding structural suspension parts should be done by a qualified fabricator using suitable tube material and technique.










