Drivetrain & Differential
Showing 793–804 of 1036 resultsSorted by popularity
-
-
Axle Upgrade Kits
Alloy USA Ford Differential Cable Lock Kit By Alloy USA – 450750
- Ford differential cable lock kit with positive manual engagement
- Not vacuum dependent; for vehicles with a front locker
- Fits 1997–2003 Ford F-150 and 2004 F-150 Heritage
- Allows 2WD low range control from inside the vehicle
SKU: ALY450750 -
-
Ring and Pinion Installation Kits
Alloy USA Dana 44 JK Non Rubicon Rear Master Ring and Pinion Installation Kit – 352053
Ring and Pinion Installation KitsAlloy USA Dana 44 JK Non Rubicon Rear Master Ring and Pinion Installation Kit – 352053
- Alloy USA 352053 Dana 44 JK non-Rubicon rear master ring and pinion kit
- Built for 2007-2018 Jeep Wrangler JK non-Rubicon rear axles
- Bearings and seals included
- Part number 352053, UPC 801773044860
SKU: ALY352053 -
Ring and Pinion Installation Kits
Alloy USA Dana 44 JK Rubicon Rear Master Ring and Pinion Installation Kit – 352052
Ring and Pinion Installation KitsAlloy USA Dana 44 JK Rubicon Rear Master Ring and Pinion Installation Kit – 352052
- Alloy USA 352052 Dana 44 JK Rubicon rear master ring and pinion installation kit
- Built for 2007-2018 Jeep Wrangler JK Rubicon rear axles
- Bearings and seals included
- Part number 352052, UPC 70000531045
SKU: ALY352052 -
Ring and Pinion Installation Kits
Alloy USA Dana 30 JK Master Ring and Pinion Installation Kit – 352050
Ring and Pinion Installation KitsAlloy USA Dana 30 JK Master Ring and Pinion Installation Kit – 352050
- Alloy USA 352050 master ring and pinion installation kit for the Dana 30 JK axle, tied to the Jeep Wrangler JK (2007-2018)
- Includes bearings, pinion seals, pinion shims, crush sleeve, pinion nut, ring gear bolts and marking compound
- Part number 352050, UPC 801773044839
SKU: ALY352050 -
Ring and Pinion Installation Kits
Alloy USA Dana 35 Rear Master Ring and Pinion Installation Kit – 352049
Ring and Pinion Installation KitsAlloy USA Dana 35 Rear Master Ring and Pinion Installation Kit – 352049
- Ring and pinion installation kit for Dana 35 rear differentials
- Part number 352049
- Includes bearings, pinion seals, pinion shims, crush sleeve and marking compound
- No vehicle is named, so check fitment before ordering
SKU: ALY352049 -
Ring and Pinion Installation Kits
Alloy USA Dana 44 TJ Master Ring and Pinion Installation Kit – 352045
Ring and Pinion Installation KitsAlloy USA Dana 44 TJ Master Ring and Pinion Installation Kit – 352045
- Alloy USA 352045, Dana 44 TJ master ring and pinion installation kit
- Built for 1997-2006 Jeep Wrangler TJ
- Includes bearings, seals, shims and crush sleeve
- Part number 352045, UPC 70000379281
SKU: ALY352045 -
Ring and Pinion Installation Kits
Alloy USA Dana 44 Master Ring and Pinion Installation Kit – 352033
Ring and Pinion Installation KitsAlloy USA Dana 44 Master Ring and Pinion Installation Kit – 352033
- Alloy USA Dana 44 master ring and pinion installation kit, part number 352033
- Includes bearings, pinion seals, pinion shims and crush sleeve
- Ring gear bolts, pinion nut and marking compound included
- Direct fit classification; gear set not included
SKU: ALY352033 -
Ring and Pinion Installation Kits
Alloy USA Dana 30 TJ Master Ring and Pinion Installation Kit – 352031
Ring and Pinion Installation KitsAlloy USA Dana 30 TJ Master Ring and Pinion Installation Kit – 352031
- Ring and pinion installation kit for Dana 30 TJ Master differentials
- Fits 1997-2006 Jeep Wrangler TJ
- Part number 352031 with bearings, pinion seals, shims and crush sleeve
- Includes pinion nut, ring gear bolts and marking compound
SKU: ALY352031
What belongs in the drivetrain
The drivetrain moves power from the crankshaft to the ground. On a typical 4x4 that means the clutch or torque converter, the transmission, the transfer case, front and rear driveshafts, and the axle assemblies with their differentials, gears, bearings and seals. The subcategories here separate those systems so you can narrow down to complete axles and third members, performance axle components, OEM-style replacement axle parts, drive shafts, shifters or transfer case upgrades.
Identify the axle before you shop
Most axle parts are specific to the axle model, spline count and sometimes the production year. Product titles in this category refer to Dana 30, Dana 35, Dana 44, Dana 80 and AMC Model 20 housings, among others. Read the data tag on the differential housing or pull the cover and count ring gear bolts and measure the ring gear diameter. A part labeled for a Dana 44 front axle will not necessarily fit a Dana 44 rear axle, so note the axle location as well as the model.
Gear ratio and differential type
- Ring and pinion ratio: a numerically higher ratio such as 4.56 or 5.38 multiplies torque more and helps larger tires turn freely, at the cost of higher engine speed on the highway.
- Matched sets: ring and pinion gears are lapped and used as a pair, and front and rear ratios must match on a four-wheel-drive vehicle.
- Open, limited-slip and locking differentials: each handles traction differently, and clutch-type limited-slip units use clutch packs and friction additives that wear over time.
Installation and setup
Gear installation depends on correct pinion depth, backlash and bearing preload. These adjustments need dial indicators, marking compound and patience, and a mistake can destroy a new gear set within a few miles. Many owners hand this work to a driveline shop. Replace crush sleeves, seals and gaskets whenever the assembly is opened, and use the gear oil grade and capacity the axle manufacturer specifies. Torque fasteners to published values.
Confirming compatibility
Always confirm fitment for your exact year, make and model, and compare the part number against the manufacturer's specifications. Spline count, axle shaft diameter, bolt pattern and housing casting numbers all matter, and cross-referencing them avoids returning the wrong part after a weekend teardown.
Maintenance habits matter as much as the parts you choose. Check axle breather tubes so they are not clogged or collapsed, since a blocked breather builds pressure and pushes oil past the seals. Inspect universal joints and slip yokes for play, grease them if they have fittings, and look at the driveshaft angles after any lift or suspension change. Vibration at a particular speed often points to a driveshaft that is out of balance or running at too steep an angle. Gear oil that looks milky has taken on water, and metallic glitter on a magnetic drain plug is a sign that something inside deserves a closer look before it fails on the trail. Keep a record of the ratio, axle model and spline count for each axle so future orders are straightforward.
When budgeting a drivetrain project, remember the supporting parts. Bearings, seals, shims, carrier hardware and fluids are all needed alongside gears, and skipping them to save a little money tends to cost more later. If you are unsure which items belong together, a driveline specialist can review your list.
Popular Drivetrain & Differential brands
- G2 Axle and Gear (320)
- Dana Spicer (127)
- Crown Automotive (115)
- Omix-Ada (63)
- Moog (59)
- Centerforce (44)
- Trail Gear (39)
- ARB 4x4 Accessories (33)
- Alloy USA (26)
- Jeep (21)
- Eaton (16)
- TeraFlex (15)
Shop Drivetrain & Differential by type
- Performance Axle Components (669)
- Drive Shafts & Drive Shaft Components (78)
- OEM Replacement Axle Parts (93)
- Complete Axles & Third Members (32)
- Clutch & Bellhousing Components (98)
- Automatic Transmissions (26)
- Shifters & Shifter Components (13)
- Transfer Cases and Replacement Parts (12)
- Transfer Case Upgrades & Crawl Boxes (7)
- Manual Transmissions Parts (5)
- Transmission and Transfer Case Mounts (6)
Drivetrain & Differential FAQ
How do I know which Dana axle I have?
Check the axle tag or stamped casting numbers on the housing, count the differential cover bolts, and look at the cover shape. Measuring the ring gear diameter after removing the cover gives a definitive answer. Confirm against the manufacturer's specifications for your year and model.
Do I need to change both axle gear ratios at once?
On a part-time or full-time four-wheel-drive vehicle, yes. Front and rear ratios must match, because mismatched ratios make the axles fight each other and can damage the transfer case and gears. Regear both axles together with the same ratio.
Is a ring and pinion set something I can install at home?
It is possible, but setting pinion depth, backlash and bearing preload takes special tools and experience. Errors cause noise and rapid wear. Many owners use a driveline shop, especially for the first gear swap.
What fluids should I replace when I work on the drivetrain?
Replace gear oil in any axle you open, plus transmission and transfer case fluid if they are involved. Use the viscosity and friction modifier requirements specified for your axle, and replace seals and gaskets while the parts are apart.




